用ttl线救活whr-g300n v2

xhoot

whr-g300n v2刷回原版的时候变成砖了-------------------------------------------------------------------------------------------------------------------------------------------
BUFFALO U-BOOT Ver 1.00
AP93 (ar7240) U-boot

sri
================================================================================
=====================================================
  TAP CALC (read_cnt=512)
----+---------------------------------------------------------------------------
-----------------------------------------------------
TAP |   0   1   2   3   4   5   6   7   8   9  10  11  12  13  14  15  16  17  1
8  19  20  21  22  23  24  25  26  27  28  29  30  31
----+---------------------------------------------------------------------------
-----------------------------------------------------
FAIL|                               0   0   0   0   0   0   0   4 512 512 512 51
   42 512 512 512 512 512 512 512 512 512 512 512 512
----+---------------------------------------------------------------------------
-----------------------------------------------------
SELECT tap0=7 / tap1=7

#### ddr registers
  B8000000 = C7BC8CD0
  B8000004 = 9DD0E6A8
  B8000008 = 00000033
  B800000C = 00000002
  B8000010 = 00000000
  B8000014 = 00004AF0
  B8000018 = 000000FF
  B800001C = 00000007
  B8000020 = 00000007
  B8000024 = 00000005
  B8000028 = 00000005


32 MB
Memory Test (address line)
Memory Test start(0xA0000000) end(0xA2000000) size(33554432)
Data line test start:0xa0000000 pattern 0x00000001 0x00000003 0x00000007 0x00000
00F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0000000 len:0x2000000 pattern 0xAAAAAAAA 0x55555555

Fill test patnum:5
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
fill Pattern 0000FFFF  Writing...   Reading...
fill Pattern FFFF0000  Writing...   Reading...
fill Pattern AAAAAAAA  Writing...   Reading...
Top of RAM usable for U-Boot at: 82000000
Reserving 291k for U-Boot at: 81fb4000
Reserving 136k for malloc() at: 81f92000
Reserving 44 Bytes for Board Info at: 81f91fd4
Reserving 36 Bytes for Global Data at: 81f91fb0
Reserving 128k for boot params() at: 81f71fb0
Stack Pointer at: 81f71f98
Now running in RAM - U-Boot at: 81fb4000
id read 0x100000ff
flash size 4194304, sector count = 1024
Flash:  4 MB
In:    serial
Out:   serial
Err:   serial
Memory Test
uboot use  81F71FB0 - 82000000
Memory Test start(80000000) end(81F00000) size(01F00000)
Pattern 00000000  Writing...  Reading...
Memory Test OK
### buf_ver=[1.00] U-Boot Ver.=[1.00]
### build_date(env)=[Jul 27 2009 - 17:39:39] build_date(bin)=[Jul 27 2009 - 17:3
9:39]
TEST----ag7240_enet_initialize...
TEST----dev[0]->name=eth0-----
TEST----dev[0]->enetaddr=-----
TEST----dev[0]->iobase=0-----
TEST----dev[0]->state=0-----
Reading MAC Address from ENV(0x81f922af)
eth_register
TEST----dev->state=0----
miiphy_register: added 'eth0', read=0x81fd0f08, write=0x81fd1060
ag7240_hw_start
TEST----mac->mac_unit=0----
TEST----AG7240_MAC_CFG2_else= 0x7337----
TEST---- mac->base=0x19000000----
TEST---- register3c=0x0----
: cfg1 0xf cfg2 0x7337
ag7240_setup_fifos
eth0: 02:aa:bb:cc:dd:1e
eth0 up
TEST----dev[1]->name=eth1-----
TEST----dev[1]->enetaddr=-----
TEST----dev[1]->iobase=0-----
TEST----dev[1]->state=0-----
No valid address in Flash. Using fixed address
eth_register
TEST----dev->state=0----
miiphy_register: added 'eth1', read=0x81fd0f08, write=0x81fd1060
ag7240_hw_start
TEST----mac->mac_unit=1----
TEST----AG7240_MAC_CFG2_else= 0x7337----
TEST---- mac->base=0x1a000000----
TEST---- register3c=0x0----
: cfg1 0xf cfg2 0x7337
ag7240_setup_fifos
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0  02:AA:BB:CCD:1E
, eth1  00:03:7F:09:0B:AD

TEST-----ag7240_check_link----
TEST----duplex=1   1:full 0:half
TEST----athrs26_phy_speed----
TEST----phyHwStatus=31772----
TEST----phyHwStatus=49152----
TEST----phyHwStatus=1----
TEST----speed=100-----
TEST----dup 1 speed 100
TEST----3C=0
TEST----04=7337

tftp server(receive) go, waiting:4[sec]
TEST-----ag7240_check_link----
TEST----duplex=1   1:full 0:half
TEST----athrs26_phy_speed----
TEST----phyHwStatus=31772----
TEST----phyHwStatus=49152----
TEST----phyHwStatus=1----
TEST----speed=100-----
Load address: 0x80f00000

TftpServer Timeout;
no file was loaded.
Bad CRC of EEPROM!!
# LED(0x2) Blink[2] (Please press 'Ctrl+c' to stop)
-------------------------------------------------------------------------------
最后用TTL线救活了
过程如下首先下载2个文件

http://115.com/file/aq7n3f3f#
firmware(whr-g300n_v2串口修复).bin
http://115.com/file/aq7n3m5l#
Cisco_TFTP_Server.rar

手动设置电脑的IP192.168.11.2
解压缩rar， 修改文件名firmware(whr-g300n_v2串口修复).bin为firmware.bin放到

Cisco_TFTP_Server目录下，运行该目录的tftpserver.exe,在查看-选项-根目录指向firmware.bin

靠近网线的数起，依次是TX RX GND 电源
速率115200，8，无，1，无
'Ctrl+c' 中断
ar7240> run ut_fw
TEST-----ag7240_check_link----
TEST----duplex=1   1:full 0:half
TEST----athrs26_phy_speed----
TEST----phyHwStatus=31774----
TEST----phyHwStatus=49152----
TEST----phyHwStatus=1----
TEST----speed=100-----
Using eth1 device
TFTP from server 192.168.11.2; our IP address is 192.168.11.1
Filename 'firmware.bin'.
Load address: 0x80f00000
Loading: TEST----STATE_RRQ
#################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ####
done
Bytes transferred = 3678208 (382000 hex)
Erase Flash from 0xbf040000 to 0xbf3effff in Bank # 1
First 0x40 last 0x3ef sector size 0x1000
992
Erased 944 sectors
Copy to Flash...
Copy 3678208 byte to Flash... write addr: bf040000
done
## Booting image at bf040000 ...
   Image Name:   MIPS Linux Kernel Image
   Created:      2011-06-14   7:10:30 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    841170 Bytes = 821.5 kB
   Load Address: 80002000
   Entry Point:  80006150
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80006150) ...
## Giving linux memsize in bytes, 33554432

xhoot

Starting kernel ...

[    0.000000] Linux version 2.6.34.9-svn17089 (root@dd-wrt) (gcc version 4.5.2
(Linaro GCC 4.5-2011.02-0) ) #6035 Tue Jun 14 09:02:10 CEST 2011
[    0.000000] flash_size passed from bootloader = 4
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Booting AR7240(Python)...
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 8128
[    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=sq
uashfs noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29756k/32768k available (1934k kernel code, 3012k reserve
d, 349k data, 144k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
[    0.240000] Mount-cache hash table entries: 512
[    0.240000] NET: Registered protocol family 16
[    0.260000] found calibration data for slot 0 on 0xBF3F1000
[    0.470000] registering PCI controller with io_map_base unset
[    0.480000] bio: create slab <bio-0> at 0
[    0.490000] pci 0000:00:00.0: fixup device configuration
[    0.490000] bootstrap returns device 168C:2A
[    0.500000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bi
t]
[    0.500000] pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff 64bit]
(PCI address [0x10000000-0x1000ffff]
[    0.510000] PCI: mapping irq 48 to pin1@0000:00:00.0
[    0.510000] fixup irq: got 48
[    0.510000] Switching to clocksource MIPS
[    0.520000] NET: Registered protocol family 2
[    0.520000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.530000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.540000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.540000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.550000] TCP reno registered
[    0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.570000] gpio_proc: module loaded and /proc/gpio/ created
[    0.580000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[    0.580000] init_vdso successfull
[    0.590000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[    0.590000] msgmni has been set to 58
[    0.600000] io scheduler noop registered
[    0.600000] io scheduler deadline registered (default)
[    0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.610000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
[    0.620000] console [ttyS0] enabled, bootconsole disabled
[    0.620000] console [ttyS0] enabled, bootconsole disabled
[    0.630000] guessed flashsize = 4M
[    0.640000] scanning for root partition
[    0.640000] uboot detected
[    0.640000] guessed bootloader size = 40000
[    0.650000]
[    0.650000] found squashfs at 10E000
[    0.660000] Creating 8 MTD partitions on "ar7240-nor0":
[    0.660000] 0x000000000000-0x000000040000 : "RedBoot"
[    0.670000] 0x000000040000-0x0000003e0000 : "linux"
[    0.670000] 0x00000010e000-0x0000003d0000 : "rootfs"
[    0.680000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[    0.690000] mtd: partition "rootfs" set to be root filesystem
[    0.700000] 0x0000003d0000-0x0000003e0000 : "ddwrt"
[    0.700000] 0x0000003e0000-0x0000003f0000 : "nvram"
[    0.710000] 0x0000003f0000-0x000000400000 : "board_config"
[    0.720000] 0x000000000000-0x000000400000 : "fullflash"
[    0.720000] 0x000000000000-0x000000040000 : "fullboot"
[    0.730000] PPP generic driver version 2.4.2
[    0.730000] PPP Deflate Compression module registered
[    0.740000] PPP BSD Compression module registered
[    0.740000] PPP MPPE Compression module registered
[    0.750000] NET: Registered protocol family 24
[    0.750000] PPPoL2TP kernel driver, V1.0
[    0.760000] IMQ driver loaded successfully.
[    0.760000]  Hooking IMQ before NAT on PREROUTING.
[    0.770000]  Hooking IMQ after NAT on POSTROUTING.
[    0.770000] tun: Universal TUN/TAP device driver, 1.6
[    0.780000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.790000] AG7240: Length per segment 1544
[    0.790000] AG7240: Max segments per packet 1
[    0.790000] AG7240: Max tx descriptor count    80
[    0.800000] AG7240: Max rx descriptor count    252
[    0.800000] AG7240: fifo cfg 3 01f00140
[    0.810000] AG7240CHH: Mac address for unit 0
[    0.810000] AG7240CHH: 00:03:7f:11:20:00
[    1.020000] AG7240CHH: Mac address for unit 1
[    1.020000] AG7240CHH: 00:03:7f:11:20:01
[    1.230000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_mar
gin=60 sec (nowayout= 0)
[    1.240000] u32 classifier
[    1.240000]     input device check on
[    1.240000]     Actions configured
[    1.250000] Netfilter messages via NETLINK v0.30.
[    1.250000] nf_conntrack version 0.5.0 (464 buckets, 1856 max)
[    1.260000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please
use
[    1.260000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module
option or
[    1.270000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    1.280000] nf_conntrack_rtsp v0.6.21 loading
[    1.280000] nf_nat_rtsp v0.6.21 loading
[    1.290000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.290000] IPP2P v0.8.2 loading
[    1.300000] TCP westwood registered
[    1.300000] TCP hybla registered
[    1.300000] TCP vegas registered
[    1.310000] NET: Registered protocol family 17
[    1.310000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    1.320000] All bugs added by David S. Miller <davem@redhat.com>
[    1.350000] Broken NVRAM found, recovering it (Magic FFFFFFFF)
[    1.360000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.370000] Freeing unused kernel memory: 144k freed
start service
starting Architecture code for whrhpgn
starting hotplug
Jan  1 00:00:02 udevtrigger[179]: parse_config_file: can't open '/etc/udev/udev.
conf' as config file: No such file or directory
done
load ATH Ethernet Driver
.........................
-----------------------------------------------------------------------------------------------------------
  run ut_fw实际命令分以下4步走

tftpboot 80f00000 firmware.bin
erase BF040000 BF3EFFFF
cp.b 80f00000  BF040000   382000
bootm BF040000
用 printenv命令看一下
----------------------------------------------------------------------------------------------------------------------
ar7240> printenv
bootargs=console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdpar
ts=ar7240-nor0:248k(u-boot),8k(u-boot-env),896k(uImage),2816k(rootfs),64k(NVRAM)
,64k(ART)
bootcmd=bootm BF040000
baudrate=115200
ethaddr=02:AA:BB:CCD:1E
tmp_ram=80F00000
tmp_bottom=81F00000
fw_eaddr=BF040000 BF3EFFFF
uboot_eaddr=BF000000 BF03DFFF
u_fw=erase $fw_eaddr; cp.b $fileaddr BF040000 $filesize; bootm BF040000;
ut_fw=tftp $tmp_ram firmware.bin; erase $fw_eaddr; cp.b $fileaddr BF040000 $file
size; bootm BF040000;
ut_uboot=tftp $tmp_ram u-boot.bin; protect off $uboot_eaddr; erase $uboot_eaddr;
cp.b $fileaddr BF000000 $filesize;
melco_id=RD_BB09087
hw_rev=0
tftp_wait=4
uboot_ethaddr=02:AA:BB:CCD:1E
DEF-p_wireless_ath0_11bg-authmode=psk
DEF-p_wireless_ath0_11bg-crypto=tkip+aes
DEF-p_wireless_ath0_11bg-authmode_ex=mixed-psk
custom_id=0
buf_ver=1.00
region=AP
accept_open_rt_fmt=1
build_date=Jul 27 2009 - 17:39:39
pincode=01742909
DEF-p_wireless_ath0_11bg-wpapsk=7egc0mvga7d31
buf_crc=92D8F716
stdin=serial
stdout=serial
stderr=serial
loadaddr=80F00000
ethact=eth1
filesize=3830f8
fileaddr=80F00000
ipaddr=192.168.11.1
serverip=192.168.11.2

Environment size: 1136/8188 bytes
--------------------------------------------------------------------------------------

crayowl

楼主很有心，将救机过程分享出来。  帮顶~

前段时间救回了自己的wr841 v7    分享些网上有用的相关帖子吧（俺比较赖，嘿嘿）

https://www.right.com.cn/forum/thread-47311-1-1.html
https://www.right.com.cn/forum/v ... &highlight=841n
http://wifi.com.cn/forum/viewthr ... 6&highlight=ttl
http://openwrt.org.cn/bbs/viewth ... p;extra=&page=1
https://www.right.com.cn/forum/viewthread.php?tid=39327
https://www.right.com.cn/forum/v ... =841%2B%BB%D6%B8%B4
http://cjzzz.blog.163.com/blog/static/1744453702011318105532561/


硬件资料：
http://www.dd-wrt.com/wiki/index.php/TP-LINK_TL-WR841ND
http://wiki.openwrt.org/zh-cn/toh/tp-link/tl-wr841nd

C496电容去掉并短接   TTL信息输出就不会乱码了~
另外需要经常刷机的，建议焊上TTL插针
找个维修店去掉C496电容 并短接 加上 焊上TTL插针 十块钱搞定。

网上这有单排4脚插针 在这有卖
http://item.taobao.com/item.htm?id=10356196201

另外给新手一点建议，不建议购买com转ttl 转接线，建议购买usb转ttl转接线。 有些笔记本没有com接口了，至少thinkpad sl系列 和 dell  d410 笔记本没有com接口 比较郁闷~   

TTL输出没信息，不妨将rx tx线对换再试试，我按照网上教程 将 com转ttl升级小板 rx 接路由的tx  com转ttl升级小板的tx接路由的rx 好像不行   对换过来  ttl才有输出信息。一阵窃喜，刷机 恢复成功。

yanglei106

哥们..我和你的问题一样
能不能把115网盘里的文件续期一下..谢谢了

litingyou

厉害厉害，难道DD不稳定，想刷回，我正想刷DD呀

jfm034

悲剧啊...按照LZ的方法没反应吔....版本跟LZ的也一样..
下边是我的TTL输出信息..

BUFFALO U-BOOT Ver 1.00
AP93 (ar7240) U-boot

sri
================================================================================
=====================================================
  TAP CALC (read_cnt=512)
----+---------------------------------------------------------------------------
-----------------------------------------------------
TAP |   0   1   2   3   4   5   6   7   8   9  10  11  12  13  14  15  16  17  1
8  19  20  21  22  23  24  25  26  27  28  29  30  31
----+---------------------------------------------------------------------------
-----------------------------------------------------
FAIL|                               0   0   0   0   0   0   0   0   0 498 512 51
5122 512 512 512 512 512 512 512 512 512 512 512 512
----+---------------------------------------------------------------------------
-----------------------------------------------------
SELECT tap0=8 / tap1=8

#### ddr registers
  B8000000 = C7BC8CD0
  B8000004 = 9DD0E6A8
  B8000008 = 00000033
  B800000C = 00000002
  B8000010 = 00000000
  B8000014 = 00004AF0
  B8000018 = 000000FF
  B800001C = 00000008
  B8000020 = 00000008
  B8000024 = 00000005
  B8000028 = 00000005


32 MB
Memory Test (address line)
Memory Test start(0xA0000000) end(0xA2000000) size(33554432)
Data line test start:0xa0000000 pattern 0x00000001 0x00000003 0x00000007 0x00000
00F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0000000 len:0x2000000 pattern 0xAAAAAAAA 0x55555555

Fill test patnum:5
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
fill Pattern 0000FFFF  Writing...   Reading...
fill Pattern FFFF0000  Writing...   Reading...
fill Pattern AAAAAAAA  Writing...   Reading...
Top of RAM usable for U-Boot at: 82000000
Reserving 291k for U-Boot at: 81fb4000
Reserving 136k for malloc() at: 81f92000
Reserving 44 Bytes for Board Info at: 81f91fd4
Reserving 36 Bytes for Global Data at: 81f91fb0
Reserving 128k for boot params() at: 81f71fb0
Stack Pointer at: 81f71f98
Now running in RAM - U-Boot at: 81fb4000
id read 0x100000ff
flash size 4194304, sector count = 1024
Flash:  4 MB
In:    serial
Out:   serial
Err:   serial
Memory Test
uboot use  81F71FB0 - 82000000
Memory Test start(80000000) end(81F00000) size(01F00000)
Pattern 00000000  Writing...  Reading...
Memory Test OK
### buf_ver=[1.00] U-Boot Ver.=[1.00]
### build_date(env)=[Jul 27 2009 - 17:39:39] build_date(bin)=[Jul 27 2009 - 17:3
9:39]
TEST----ag7240_enet_initialize...
TEST----dev[0]->name=eth0-----
TEST----dev[0]->enetaddr=-----
TEST----dev[0]->iobase=0-----
TEST----dev[0]->state=0-----
Reading MAC Address from ENV(0x81f922d9)
eth_register
TEST----dev->state=0----
miiphy_register: added 'eth0', read=0x81fd0f08, write=0x81fd1060
ag7240_hw_start
TEST----mac->mac_unit=0----
TEST----AG7240_MAC_CFG2_else= 0x7337----
TEST---- mac->base=0x19000000----
TEST---- register3c=0x0----
: cfg1 0xf cfg2 0x7337
ag7240_setup_fifos
eth0: 02:aa:bb:cc:dd:1e
eth0 up
TEST----dev[1]->name=eth1-----
TEST----dev[1]->enetaddr=-----
TEST----dev[1]->iobase=0-----
TEST----dev[1]->state=0-----
No valid address in Flash. Using fixed address
eth_register
TEST----dev->state=0----
miiphy_register: added 'eth1', read=0x81fd0f08, write=0x81fd1060
ag7240_hw_start
TEST----mac->mac_unit=1----
TEST----AG7240_MAC_CFG2_else= 0x7337----
TEST---- mac->base=0x1a000000----
TEST---- register3c=0x0----
: cfg1 0xf cfg2 0x7337
ag7240_setup_fifos
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0  02:AA:BB:CCD:1E
, eth1  00:03:7F:09:0B:AD

TEST-----ag7240_check_link----
TEST----duplex=1   1:full 0:half
TEST----athrs26_phy_speed----
TEST----phyHwStatus=31774----
TEST----phyHwStatus=49152----
TEST----phyHwStatus=1----
TEST----speed=100-----
TEST----dup 1 speed 100
TEST----3C=0
TEST----04=7337

tftp server(receive) go, waiting:4[sec]
TEST-----ag7240_check_link----
TEST----duplex=1   1:full 0:half
TEST----athrs26_phy_speed----
TEST----phyHwStatus=31774----
TEST----phyHwStatus=49152----
TEST----phyHwStatus=1----
TEST----speed=100-----
Load address: 0x80f00000

TftpServer Timeout;
no file was loaded.
## Booting image at bf040000 ...
   Image Name:   Linux Kernel Image
   Created:      2009-10-08   2:15:03 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    895439 Bytes = 874.5 kB
   Load Address: 80000000
   Entry Point:  8029b000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8029b000) ...
## Giving linux memsize in bytes, 33554432

Starting kernel ...

jfm034

我的是买回来刷了DD的..后来不太稳定.想回原厂就在Web下升级了原厂的包就启不了了...

TTL是在终端机输出的...按Crtl+C一直都没任何响应啊...

请教高人方法...有没得可救活这路由...在这先感谢了.. 感觉网上搜的很多种方法都不太适合我这款的..关键是Ctrl+C没响应...

邮箱:jfm034@163.com

谢谢..

然后七年

jfm034 发表于 2012-2-26 14:11
我的是买回来刷了DD的..后来不太稳定.想回原厂就在Web下升级了原厂的包就启不了了...

TTL是在终端机输出 ...

这款路由可以用linux下tftp轻松刷回、不需要这么麻烦、

錯`、覺

我想问问ttl怎么接线。。。
email:303198069@qq.com

秦力

我的也在摸索中 ，，，，，

yeezi

接法看这里http://scarygliders.net/2010/02/ ... ffalo-wzr-hp-g300n/

yflwz

谢谢，刚刚把自己的路由活了