今天刚到的华美三合一3G路由拆了。求鉴定。

aini5354

多少钱啊？？？？、、

学习中

这个我也买了，真的不错，功能全，比TP703n好多了

luo_12yan

可惜，不能刷第三方固件！

heishou

电池后的3个点是ttl的U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)

Board: Ralink APSoC DRAM:  16 MB
relocate_code Pointer at: 80fb4000
spi_wait_nsec: 42
spi device id: c8 40 16 c8 40 (4016c840)
find flash: G 1407
raspi_read: from:30000 len:1000
.*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.6.0.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 128 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 16 MBytes
Flash component: SPI Flash
Dateec 13 2011  Time:13:49:42
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 360 MHZ ####
estimate memory size =16 Mbytes
raspi_read: from:40028 len:6
.
raspi_read: from:0 len:30004
....*************Is_update = 0 plat = 1**************

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     1
You choosed 3
                                                                              0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
.   Image Name:   Linux Kernel Image
   Created:      2012-01-04  14:24:46 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3803191 Bytes =  3.6 MB
   Load Address: 80000000
   Entry Point:  8027a000
raspi_read: from:50040 len:3a0837
...........................................................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8027a000) ...
## Giving linux memsize in MB, 16

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.21 (root@localhost.localdomain) (gcc version 3.4.2) #94 Sat Dec 31 21:10:20 CST 2011

The CPU frequency set to 360 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 40808048, status = 11000000
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 0015f900(1440000)
CPU frequency 360.00 MHz
Using 180.000 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13496k/16384k available (2221k kernel code, 2888k reserved, 310k data, 116k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
deice id : c8 40 16 c8 40 (4016c840)
Warning: un-recognized chip ID, please update SPI driver!
AT25DF321(1f 47000000) (4096 Kbytes)
mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 7 MTD partitions on "raspi":
0x00000000-0x00400000 : "ALL"
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x00121877 : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x00121877-0x01000000 : "RootFS"
mtd: partition "RootFS" extends beyond the end of device "raspi" -- size truncated to 0x2de789
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x00050000-0x01000000 : "Kernel_RootFS"
mtd: partition "Kernel_RootFS" extends beyond the end of device "raspi" -- size truncated to 0x3b0000
RT3xxx EHCI/OHCI init.
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
Hame plat 1
Ralink gpio driver initialized [003c4001]
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.8 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 253
Ralink APSoC Ethernet Driver Initilization. v2.1  256 rx/tx descriptors allocated, mtu = 1500!
MAC_ADRH -- : 0x00009c41
MAC_ADRL -- : 0x7c241a35
PROC INIT OK!
IMQ starting with 2 devices...
IMQ driver loaded successfully.
        Hooking IMQ after NAT on PREROUTING.
        Hooking IMQ before NAT on POSTROUTING.
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.1
block2mtd: version $Revision: 1.1.1.1 $
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (128 buckets, 1024 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
init started: BusyBox v1.12.1 (2011-10-22 23:04:50 CST)
starting pid 14, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
devpts: called with bogus options
-------------------------------------------
Welcome to
        __  __     __     __    __  ______
        | | | |   /  \   |  \  /  | | ____|
        | |_| |  / /\ \  | |\\//| | | |___
        |  _  | |_/__\ \ | | \/ | | | |___|
        | | | | | |  | | | |    | | | |___
        |_| |_| |_|  |_| |_|    |_| |_____|
        HameData Technology Co., Ltd
-------------------------------------------
killall: goahead: no process killed

heishou

编程器备份的固件可以找我要 qq 76596752 注明一下就可以了

luo_12yan

哦！还真有高手哇！
电池后面是四个点吧。。一个3.3V 一个地。还有两条串口数据线。

好了

我也买了个，中继功能不是很理想，手机可以收到的信号，A1收不到，不过各种宽带转WIFI功能，很好用，也比较稳定，配上华为1260,可以用4小时以上，然后还显示剩1格电，应该有近5小时把。如果是做移动电源给手机充电，估计电池寿命难熬，这个电池要是可以搞成可以换的方案就好了，没地方配，不知道华美他们有这个电池卖没。

如果这个A1下个版的再加2功能，就完美了，1：可以在WEB后台读短信。2、可以在WEB后台设置WIFI运行功率

wack

暂时不支持吧
内存可以换32M sdram

然后跟dir-600 B5应该差不多了
等dd-wrt吧，最先支持的应该是这个

唯一999

“LZ” A1的天线在哪个部位？如何接外接天线？    力顶此贴

dsldsl

这个电池容量也太小了点，给手机根本冲不了什么电啊，等我做一个更大容量的移动电源路由器出来。

rzd4evr

luo_12yan 发表于 2012-3-1 16:50
这个主控的一些资料：
Features
    1T1R 2.4/5 GHz with 150 Mbps PHY data rate

那4个点估计是TTL

gdsgds

heishou 发表于 2012-3-22 07:55
电池后的3个点是ttl的U-Boot 1.1.7 (Dec 13 2011 - 13:49:42)

Board: Ralink APSoC DRAM:  16 MB

哪三个点，能具体说一下么。我的和楼主的一样，有四个点，没标。

313176904

好像是可以刷op的吧

betalin

luo_12yan 发表于 2012-3-1 16:50
这个主控的一些资料：
Features
    1T1R 2.4/5 GHz with 150 Mbps PHY data rate

那个应该不是jtag
串行flash 用jtag来干嘛 在线就能烧 也是几条线