|
过期的可乐 发表于 2012-4-29 08:09
谢谢你的反馈。我只用了完美的CFE,改了MAC地址后,电源灯不闪烁了, 运行时常绿。LAN4灯也由橙色变为绿色 ...
按那贴,现在路由彻底成砖了。。。
CFE by dindindang@msn.com
Build Date:2010-07-15
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.138.1.0
CFE by dindindang@msn.com
Build Date:2010-07-15
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.138.1.0
Device eth0: hwaddr 00-1F-33-2D-C4-3C, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
gpio=0xD0
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: Failed.
Could not load :: Interrupted
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> flash -noheader : flash1.boot
Reading :: Done. 262144 bytes read
Programming...done. 262144 bytes written
*** command status = 0
CFE> tftp -i 192.168.1.1 put cfe1.bin
Invalid command: "tftp"
Available commands: et, go, nvram, reboot, tftpd, flash, autoboot, batch, boot, load, save, ifconfig, unsetenv, printenv, setenv, help
*** command status = -1
CFE> tftp -i 192.168.1.1 put cfe1.bin
Invalid command: "tftp"
Available commands: et, go, nvram, reboot, tftpd, flash, autoboot, batch, boot, load, save, ifconfig, unsetenv, printenv, setenv, help
*** command status = -1
CFE>
CFE> flash -noheader : flash1.boot
Reading :: Done. 262144 bytes read
Programming...done. 262144 bytes written
*** command status = 0
CFE> tftp -i 192.168.1.1 put cfe.bin
Invalid command: "tftp"
Available commands: et, go, nvram, reboot, tftpd, flash, autoboot, batch, boot, load, save, ifconfig, unsetenv, printenv, setenv, help
*** command status = -1
CFE> rteboopt
Invalid command: "rteboopt"
Available commands: et, go, nvram, reboot, tftpd, flash, autoboot, batch, boot, load, save, ifconfig, unsetenv, printenv, setenv, help
*** command status = -1
CFE> reboot
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Oct 9 13:28:26 EDT 2007 (tornado@dd-wrt.com)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing Devices.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
CPU type 0x29029: 240MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80700000 - 0x807977D0 (620496)
Initialized Data: 0x8072E860 - 0x80730FB0 (10064)
BSS Area: 0x80730FB0 - 0x807317D0 (2080)
Local Heap: 0x807317D0 - 0x807957D0 (409600)
Stack Area: 0x807957D0 - 0x807977D0 (8192)
Text (code) segment: 0x80700000 - 0x8072E860 (190560)
Boot area (physical): 0x00798000 - 0x007D8000
Relocation Factor: I:00000000 - D:00000000
Committing NVRAM...done
DHCP registration failed on device eth0
Invalid boot block on disk
Reading :: Failed.: Error
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: . 0 bytes read
Failed.
Could not load flash0.os:: Error
CFE> flash -noheader : flash1.boot
Reading :: Failed.: Error
*** command status = -1
CFE> flash -noheader : flash1.boot
Reading :: Failed.: Error
*** command status = -1
CFE> flash -noheader : flash0.boot
Reading :: Failed.: Error
*** command status = -1
CFE> flash -noheader : flash0.boot
Reading :: Failed.: Error
*** command status = -1
CFE> tftp -i 192.168.1.1 put cfe2.bin
Invalid command: "tftp"
Available commands: et, nvram, reboot, flash, autoboot, batch, go, boot, load, save, ping, arp, ifconfig, unsetenv, printenv, setenv, help
*** command status = -1
|
|