设为首页收藏本站

简体中文 繁體中文 English 日本語 Deutsch 한국 사람 بالعربية TÜRKÇE português คนไทย

切换到窄版

 找回密码
 立即注册

QQ登录

只需一步，快速开始

搜索
恩山无线论坛»论坛 › 无线设备硬件相关板块 › 无线路由器硬件改造以及故障维修 › BUFFALO WZR-HP-G300NH2救砖成功,庆贺一下!
广告投放联系QQ68610888
返回列表 发新帖
查看: 1740|回复: 3

BUFFALO WZR-HP-G300NH2救砖成功,庆贺一下!

[复制链接]
xcb***
| 显示全部楼层 |阅读模式
BUFFALO WZR-HP-G300NH2在线升级固件成砖，网上搜索很多的救治方案都没有成功，电脑系统从WIN10退回到winxp，一直到win7x32，成功刷进数据，成功救机。采用SecureCRT软件，连接TTL数据线监测路由器读写数据，从网上搜索到的办法中，采用自动TFTP上传工具，失败，用TFTP32工具上传数据，失败，最后，采用CMD命令，成功上传数据。附cmd命令。route print，查看网卡端口信息，绑定电脑网卡：netsh interface ipv4 add neighbors 14 192.168.11.1 02-aa-bb-cc-dd-1a，然后输入tftp -i 192.168.11.1 put d:\wzr-hp-g300nh2命令，路由器插电，数12秒左右再敲回车键，成功输入数据，数据输入只用了9秒，cmd命令窗有显示写入数据时间及写入数据速度，然后就是漫长的固件升级过程，我用ttl线监测，数据升级大约12分钟，路由器正常工作。
附ttl线监测数据：
BUFFALO U-BOOT Ver 1.11
  == CPU:400MHz, DDR:400MHz, AHB:200MHz ==
PB93 (ar7241 - Virian) U-boot
DRAM:  64 MB
WAN port disabling: done
Top of RAM usable for U-Boot at: 84000000
Reserving 267k for U-Boot at: 83fbc000
Reserving 192k for malloc() at: 83f8c000
Reserving 44 Bytes for Board Info at: 83f8bfd4
Reserving 36 Bytes for Global Data at: 83f8bfb0
Reserving 128k for boot params() at: 83f6bfb0
Stack Pointer at: 83f6bf98
Now running in RAM - U-Boot at: 83fbc000
flash bank #0 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
flash bank #1 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Memory Test
uboot use  83F6BFB0 - 84000000
Memory Test start(80000000) end(83F00000) size(03F00000)
Pattern 00000000  Writing...  Reading...
Memory Test OK
### buf_ver=[1.11] U-Boot Ver.=[1.11]
### build_date(env)=[Feb  9 2012 - 19:38:20] build_date(bin)=[Feb  9 2012 - 19:38:20]
ag7240_enet_initialize...
Reading MAC Address from ENV(0x83f8c2f8)
No valid address in Flash. Using fixed address
Virian MDC CFG Value ==> 4
: cfg1 0x7 cfg2 0x7014
eth0: 02:aa:bb:cc:dd:1a
eth0 up
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0  02:AA:BB:CCD:1A
, eth1  00:03:7F:09:0B:AD

dup 1 speed 1000

tftp server(receive) go, waiting:4[sec]
Load address: 0x81f00000
$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$
tftp server done
Bytes transferred = 3473616 (3500d0 hex)
change bootargs
console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties) mem=64M product_rev=1 UART=1
## Booting image at bf060000 ...
   Image Name:   Linux Rootfs Combined Image
   Created:      2013-02-07  13:41:04 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    24100800 Bytes = 23 MB
   Load Address: 80002000
   Entry Point:  8020d000
   Verifying Checksum ... crc32_fw: bf060040 - c075bfff (len:016fbfc0) calc...
crc32_fw: range1 bf060040 - bfffffff, range2 be000000 - be75bfff
Bad Data CRC
# LED(0x10000) Blink[2] (Please press 'Ctrl+c' to stop)


路由器升级过程读取数据：

insmod: cannot insert `/lib/modules/2.6.15/net/wlan_acl.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_me.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_me.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_pktlog.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_pktlog.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_scan_ap.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_scan_ap.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_scan_sta.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_scan_sta.ko': Invalid parameters (17): Invalid argument
wlctl-country_code_select.c(110) WLCTL_CountryCode_From_Region_rev001 EBUG:region=CH iCountryCode=276
Interface doesn't accept private ioctl...
setCountryID (8BE0): Operation not supported
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
Using /lib/modules/kernel/drivers/buffalo/mcsnoop.ko
mcsnoop: flush all snoop entry
debug : Enter [BRCTL_ADD_RULE_IF]
add_if 00000200 ***************************
rc_lanif.c(475) StartOfrc_lanif :xPPoE Path throw?


mcsnoop_br_ioctl_device:239: mcast_maxage 300000 / 1000
wanctl-lib.c(1369) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth1] a_iCmd:[35093(-219)]:a_iCommand errorcode:126
Cannot assign requested address
MidLayerModDep.c(819) startModules :INFO:Started  module rc_lanif 1061[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_udhcpd
udhcpd (v0.9.9-pre) started
max_leases value (256) not sane, setting to 64 instead
MidLayerModDep.c(819) startModules :INFO:Started  module rc_udhcpd 41[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_usb_device_server
Using /lib/modules/kernel/drivers/usb/netusb/sxuptp.ko
Using /lib/modules/kernel/drivers/usb/netusb/sxuptp_driver.ko
Using /lib/modules/kernel/drivers/usb/netusb/jcp.ko
rc_usb_device_server.c(107) InsmodDeviceServer :debug-usbnet:insmod jcp_cmd product=WZR-HP-G300NH2
Using /lib/modules/kernel/drivers/usb/netusb/jcp_cmd.ko
MidLayerModDep.c(819) startModules :INFO:Started  module rc_usb_device_server 397[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_httpd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_httpd 26[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless_pre
wlctl-ath.c(6201) Wireless_Insmod :ERR:####### Wireless_Insmod #########
Using /lib/modules/2.6.15/net/ath_hal.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_hal.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_rate_atheros.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_rate_atheros.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_dev.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_dev.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_pci.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_pci.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_xauth.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_xauth.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_ccmp.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_ccmp.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_tkip.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_tkip.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_wep.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_wep.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_acl.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_acl.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_me.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_me.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_pktlog.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_pktlog.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_scan_ap.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_scan_ap.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_scan_sta.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_scan_sta.ko': Invalid parameters (17): Invalid argument
wlctl-country_code_select.c(110) WLCTL_CountryCode_From_Region_rev001 EBUG:region=CH iCountryCode=276
Interface doesn't accept private ioctl...
setCountryID (8BE0): Operation not supported
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless_pre 768[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless11bg
Waiting for Wireless Events from interfaces...
16:00:07.962755   ath0     Set ESSID:"106F3F3D5224"
16:00:07.979305   ath0     Set Channel:0
16:00:07.993813   ath0     Set Mode:Master
16:00:08.007898   ath0     Set Encryption keyff
set Buffalo Capability = 00000009
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless11bg 1049[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless11bg_mac_limit
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless11bg_mac_limit 89[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_as_repeater
rc_as_repeath0: WDS Proirity mask Enable prio:3
ater.c(237) StartOfrc_as_repeater :as_repeater:[Start Repeater]
rc_as_repeater.c(322) StartOfrc_as_repeater :ina:[Start Pairent Mode]
ath0      extcmd:
ath1: WDS Proirity mask Enable prio:3
ath1      extcmd:
ath3: WDS Proirity mask Enable prio:3
ath3      extcmd:
MidLayerModDep.c(819) startModules :INFO:Started  module rc_as_repeater 48[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless_post
debug : Enter [BRCTL_ADD_RULE_IF]
add_if 00000100 ***************************
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless_post 36[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_nas
killall: hostapd: no process killed
MidLayerModDep.c(819) startModules :INFO:Started  module rc_nas 43[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_aoss_mssid
MidLayerModDep.c(819) startModules :INFO:Started  module rc_aoss_mssid 57[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ap_serv
Configuration file: /tmp/hostapd.conf_ath0
->setpid 0x47b080
pid: /var/run/hostapd.ath0.pid
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ap_serv 184[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanif_select
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_dhcpcd)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_0)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_1)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_2)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_3)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_4)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_50)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_auto_detect)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanif_select 4[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanif
wanctl-lib.c(1369) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth1] a_iCmd:[35093(-219)]:SIOCGIFADDR errorcode:126
Cannot assign requested addrthresh62=33, thresh62_ext=33
ess
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanif 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wancthresh62=33, thresh62_ext=33
tl_pre
16:00:09.304572   ath0     Set Mode:Master
Using interface ath0 with hwaddr 10:6f:3f:3d:52:24 and ssid '106F3F3D5224'
Flushing old station entries
Deauthenticate all stations
l2_packet_receive - recvfrom: Network is down
l2_packet_receive - recvfrom: Network is down
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pre 3134[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
ch01: 6 pt
ch02: 12 pt
ch03: 6 pt
ch04: 0 pt
ch05: 2 pt
ch06: 5 pt
ch07: 2 pt
ch08: 5 pt
ch09: 2 pt
ch10: 0 pt
ch11: 0 pt
ch01: 20 pt ->Ch 1: 20
ch02: 21 pt ->Ch 2: 21
ch03: 13 pt ->Ch 3: 13
ch04: 8 pt ->Ch 4: 8
ch05: 5 pt ->Ch 5: 5
ch06: 8 pt ->Ch 6: 8
ch07: 6 pt ->Ch 7: 6
ch08: 8 pt ->Ch 8: 8
ch09: 4 pt ->Ch 9: 4
ch10: 2 pt ->Ch 10: 2
ch11: 0 pt ->Ch 11: 0
ch12: 0 pt ->ASS
ch13: 0 pt ->ASS
[20M]
ap_chansel_end: find channel 11 ch [00010080]
Country ie is DE
thresh62=33, thresh62_ext=33
ath_beacon_config.Configured SWBA :6,DMA resp time:4 for slotDur:100
16:00:13.418426   ath0     Scan request completed
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_dhcpcd)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect 3091[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_dummy
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_dummy 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_dhcpcd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_dhcpcd 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_0
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_0 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_1
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_1 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_2
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_2 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_3
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_3 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_4
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_4 4[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_check
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_check 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_manual
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_manual 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_dhcpcd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_dhcpcd 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_0
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_0 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_1
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_1 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_2
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_2 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_3
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_3 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_4
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_4 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_check
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_check 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanif_modem
rc_wanif_modem.c(44) StartOfrc_wanif_modem :x:SKIP Module module (StartOfrc_wanif_modem)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanif_modem 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_modem_detect
rc_wanctl_modem_detect.c(108) StartOfrc_wanctl_modem_detect :x:SKIP Module module (StartOfrc_wanctl_modem_detect)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_modem_detect 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_modem_detect_dummy
rc_wanctl_modem_detect_dummy.c(88) StartOfrc_wanctl_modem_detect_dummy :x:SKIP Module module (StartOfrc_wanctl_modem_detect_dummy)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_modem_detect_dummy 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_ppp_modem
rc_wanctl_ppp_modem.c(290) StartOfrc_wanctl_ppp_modem :x:SKIP Module module (StartOfrc_wanctl_ppp_modem)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_ppp_modem 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_post
route: SIOC[ADD|DEL]RT: No such process
wanctl-lib.c(1369) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth1] a_iCmd:[35093(-219)]:a_iCommand errorcode:126
Cannot assign requested address
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_post 143[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoeroute
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoeroute 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_dnrd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_dnrd 20[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_netwatchd
wanctl-wanstate_check.c(910) wanstate_check_main :wanctl:Start wanstate_check Daemon
wanctl-lib.c(5019) NtpFunctionControle :x:ntp-client disable
MidLayerModDep.c(819) startModules :INFO:Started  module rc_netwatchd 173[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter
iptables: Bad rule (does a matching rule exist in that chain?)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter 719[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_simple
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_simple 68[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_user
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_user 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_p p t p
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_p p t p 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_nat
Using /lib/modules/kernel/net/ipv4/netfilter/ip_conntrack_p p t p.ko
ip_conntrack_p p t p version 3.1 loaded
Using /lib/modules/kernel/net/ipv4/netfilter/ip_nat_p p t p.ko
ip_nat_p p t p version 3.0 loaded
MidLayerModDep.c(819) startModules :INFO:Started  module rc_nat 199[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_routectl
MidLayerModDep.c(819) startModules :INFO:Started  module rc_routectl 49[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_lltd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_lltd 71[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wsc
Execute wscconfig init
SAMPLE!!
Execute wscconfig stop
Execute wscconfig start
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wsc 245[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_upnp
iptables v1.3.5: Couldn't find target `UPNP-PREROUTING-CHAIN'

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 0.3.1d, April 24 2006
*********************************************
iptables v1.3.5: Couldn't find target `UPNP-POSTROUTING-CHAIN'

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
MidLayerModDep.c(819) startModules :INFO:Started  module rc_upnp 471[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_movie_engine
wlctl-ath.c(3567) wlconf_chg_movie_engine_profile :x:MOVIE_ENGINE_MODE_OFF
mcsnoop_br_ioctl_device:239: mcast_maxage 300000 / 1000
ath0      extcmd:
ath0      extcmd:
set Buffalo Capability = 00000009
ath0      extcmd:
ath1      extcmd:
ath1      extcmd:
set Buffalo Capability = 00000009
ath1      extcmd:
ath2      extcmd:
ath2      extcmd:
set Buffalo Capability = 00000009
ath2      extcmd:
ath3      extcmd:
ath3      extcmd:
set Buffalo Capability = 00000009
ath3      extcmd:
wlctl-ath.c(3407) wlconf_modified_reset_paththrow :xIPv6) AS_BEHAVIOR_MODE_ROUTER
debug : Enter [BRCTL_ADD_IF]
MidLayerModDep.c(819) startModules :INFO:Started  module rc_movie_engine 527[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ntpclient
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ntpclient 37[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_eco
/dev/set_clock: cannot create
MidLayerModDep.c(819) startModules :INFO:Started  module rc_eco 182[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wan_qos
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wan_qos 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_p p t p_server
MidLayerModDep.c(819) startModules :INFO:Started  module rc_p p t p_server 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_p p t p_server_route
MidLayerModDep.c(819) startModules :INFO:Started  module rc_p p t p_server_route 105[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_nastorage
MidLayerModDep.c(819) startModules :INFO:Started  module rc_nastorage 4[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_auto_fwup
MidLayerModDep.c(819) startModules :INFO:Started  module rc_auto_fwup 70[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_end_signal
MidLayerModDep.c(819) startModules :INFO:Started  module rc_end_signal 12[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_timer_reboot
MidLayerModDep.c(819) startModules :INFO:Started  module rc_timer_reboot 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_dst_timer
MidLayerModDep.c(819) startModules :INFO:Started  module rc_dst_timer 0[msec]
led_mask_11g_chip:f0
reg:000000B0 [CC35CC35 --> CC35CC35]
reg:000000B4 [CA35CA35 --> CA35CA35]
reg:000000B8 [C935C935 --> C935C935]
cannot open connection to btpd in //.btpd (No such file or directory).
wanctl_fwupdate.c(191) GetFirmwareListFromInternet EBUG:pUrl:http://buffalo.jp/download/drive ... r_hp_g300nh2_ch.txt
wanctl-lib.c(3742) GetDataFromInternet EBUG:parse_url start
wanctl-lib.c(3744) GetDataFromInternet EBUG:parse_url end
wanctl-lib.c(3747) GetDataFromInternet EBUG:server.host : buffalo.jp
wanctl-lib.c(3748) GetDataFromInternet EBUG:target.path : download/driver/lan/autoup/wzr_hp_g300nh2_ch.txt
wanctl-lib.c(3754) GetDataFromInternet EBUG:lookup_host start
wanctl-lib.c(3518) GetHostByNameWithTimeOut EBUG:Waiting for GetHostByName's End... 0
killall: twonkymedia: no process killed
killall: twonkymediaserver: no process killed
rc_nastorage.c(2571) NastorageStop_BitTorrent2 :x:btpd STOP-SUCCESS (0 sec)
rcUtil_usb.c(2643) UsbStorageInfo_Update :x:UsbStorageInfo_Update
MidLayerLEDSW.c(2278) MLLE_WaitSwitch :x:Modified Movie Engine Switch
wlctl-ath.c(3567) wlconf_chg_movie_engine_profile :x:MOVIE_ENGINE_MODE_OFF
mcsnoop_br_ioctl_device:239: mcast_maxage 300000 / 1000
Initializing stack... OK
Now starting stack
wanctl-lib.c(3518) GetHostByNameWithTimeOut EBUG:Waiting for GetHostByName's End... 1
main.c(280) main :xMLIST RESTORE START
main.c(283) main :xMLIST RESTORE END
DEVICE PIN: 38489662

******* MODE: AP with built-in Registrar and UPnP Proxy *******

checking for PUSH BUTTON
devpwd is not setted, but start InitiateRegistrarion.
Waiting for Client to connect(using IEs)...
ath0      extcmd:
ath0      extcmd:
set Buffalo Capability = 00000009
ath0      extcmd:
ath1      extcmd:
ath1      extcmd:
set Buffalo Capability = 00000009
ath1      extcmd:
wanctl-lib.c(3518) GetHostByNameWithTimeOut EBUG:Waiting for GetHostByName's End... 2
ath2      extcmd:
ath2      extcmd:
set Buffalo Capability = 00000009
ath2      extcmd:
ath3      extcmd:
ath3      extcmd:
set Buffalo Capability = 00000009
ath3      extcmd:
wlctl-ath.c(3407) wlconf_modified_reset_paththrow :xIPv6) AS_BEHAVIOR_MODE_ROUTER
debug : Enter [BRCTL_ADD_IF]
wanctl-lib.c(3518) GetHostByNameWithTimeOut EBUG:Waiting for GetHostByName's End... 3
wanctl-lib.c(3518) GetHostByNameWithTimeOut EBUG:Waiting for GetHostByName's End... 4
wanctl-lib.c(3756) GetDataFromInternet :ERROR:cannot lookup_host buffalo.jp
ARPING to 192.168.11.1 from 192.168.11.1 via br0
Sent 1 probes (1 broadcast(s))
Received 0 reply
MidLayerLEDSW.c(2278) MLLE_WaitSwitch :x:Modified Movie Engine Switch
wlctl-ath.c(3482) wlconf_chg_movie_engine_profile :x:[ MOVIE_ENGINE_MODE_ON]
mcsnoop_br_ioctl_device:239: mcast_maxage 300000 / 1000
ath0      extcmd:
ath0      extcmd:
ath0      extcmd:
set Buffalo Capability = 00000009
ath0      extcmd:
ath1      extcmd:
ath1      extcmd:
ath1      extcmd:
set Buffalo Capability = 00000009
ath1      extcmd:
ath2      extcmd:
ath2      extcmd:
ath2      extcmd:
set Buffalo Capability = 00000009
ath2      extcmd:
ath3      extcmd:
ath3      extcmd:
ath3      extcmd:
set Buffalo Capability = 00000009
ath3      extcmd:
wlctl-ath.c(3407) wlconf_modified_reset_paththrow :xIPv6) AS_BEHAVIOR_MODE_ROUTER
wlctl-ath.c(3432) wlconf_modified_reset_paththrow :x:Cmd = brctl addrif br0debug : Enter [BRCTL_ADD_RULE_IF]
eth1 1026  

add_if 00000402 ***************************

MidLayerLEDSW.c(2278) MLLE_WaitSwitch :x:Modified Movie Engine Switch
wlctl-ath.c(3567) wlconf_chg_movie_engine_profile :x:MOVIE_ENGINE_MODE_OFF
mcsnoop_br_ioctl_device:239: mcast_maxage 300000 / 1000
ath0      extcmd:
ath0      extcmd:
set Buffalo Capability = 00000009
ath0      extcmd:
ath1      extcmd:
ath1      extcmd:
set Buffalo Capability = 00000009
ath1      extcmd:
ath2      extcmd:
ath2      extcmd:
set Buffalo Capability = 00000009
ath2      extcmd:
ath3      extcmd:
ath3      extcmd:
set Buffalo Capability = 00000009
ath3      extcmd:
wlctl-ath.c(3407) wlconf_modified_reset_paththrow :xIPv6) AS_BEHAVIOR_MODE_ROUTER
debug : Enter [BRCTL_ADD_IF]


升级完成后路由器启动监测数据
Using /lib/modules/kernel/fs/nls/nls_cp437.ko
Using /lib/modules/kernel/fs/nls/nls_utf8.ko
change fat_tz_minuteswest = -480
MidLayerModDep.cOK1(819) startModulOK2es :INFO:Started  module rc_usbmod 1133[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wiredlan
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wiredlan 17[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module id
MidLayerModDep.c(819) startModules :INFO:Started  module id 2[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module lang
MidLayerModDep.c(819) startModules :INFO:Started  module lang 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_lanif
wlctl-ath.c(6201) Wireless_Insmod :ERR:####### Wireless_Insmod #########
Using /lib/modules/2.6.15/net/ath_hal.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_hal.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_rate_atheros.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_rate_atheros.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_dev.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_dev.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_pci.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_pci.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_xauth.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_xauth.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_ccmp.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_ccmp.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_tkip.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_tkip.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_wep.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_wep.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_acl.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_acl.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_me.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_me.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_pktlog.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_pktlog.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_scan_ap.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_scan_ap.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_scan_sta.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_scan_sta.ko': Invalid parameters (17): Invalid argument
wlctl-country_code_select.c(110) WLCTL_CountryCode_From_Region_rev001 EBUG:region=CH iCountryCode=276
Interface doesn't accept private ioctl...
setCountryID (8BE0): Operation not supported
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
Using /lib/modules/kernel/drivers/buffalo/mcsnoop.ko
mcsnoop: flush all snoop entry
debug : Enter [BRCTL_ADD_RULE_IF]
add_if 00000200 ***************************
rc_lanif.c(475) StartOfrc_lanif :xPPoE Path throw?


mcsnoop_br_ioctl_device:239: mcast_maxage 300000 / 1000
wanctl-lib.c(1369) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth1] a_iCmd:[35093(-219)]:a_iCommand errorcode:126
Cannot assign requested address
MidLayerModDep.c(819) startModules :INFO:Started  module rc_lanif 1060[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_udhcpd
udhcpd (v0.9.9-pre) started
max_leases value (256) not sane, setting to 64 instead
MidLayerModDep.c(819) startModules :INFO:Started  module rc_udhcpd 42[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_usb_device_server
Using /lib/modules/kernel/drivers/usb/netusb/sxuptp.ko
Using /lib/modules/kernel/drivers/usb/netusb/sxuptp_driver.ko
Using /lib/modules/kernel/drivers/usb/netusb/jcp.ko
rc_usb_device_server.c(107) InsmodDeviceServer :debug-usbnet:insmod jcp_cmd product=WZR-HP-G300NH2
Using /lib/modules/kernel/drivers/usb/netusb/jcp_cmd.ko
MidLayerModDep.c(819) startModules :INFO:Started  module rc_usb_device_server 397[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_httpd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_httpd 25[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless_pre
wlctl-ath.c(6201) Wireless_Insmod :ERR:####### Wireless_Insmod #########
Using /lib/modules/2.6.15/net/ath_hal.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_hal.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_rate_atheros.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_rate_atheros.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_dev.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_dev.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_pci.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_pci.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_xauth.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_xauth.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_ccmp.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_ccmp.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_tkip.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_tkip.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_wep.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_wep.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_acl.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_acl.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_me.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_me.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/ath_pktlog.ko
insmod: cannot insert `/lib/modules/2.6.15/net/ath_pktlog.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_scan_ap.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_scan_ap.ko': Invalid parameters (17): Invalid argument
Using /lib/modules/2.6.15/net/wlan_scan_sta.ko
insmod: cannot insert `/lib/modules/2.6.15/net/wlan_scan_sta.ko': Invalid parameters (17): Invalid argument
wlctl-country_code_select.c(110) WLCTL_CountryCode_From_Region_rev001 EBUG:region=CH iCountryCode=276
Interface doesn't accept private ioctl...
setCountryID (8BE0): Operation not supported
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
wlanconfig: ioctl: Invalid argument
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless_pre 768[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless11bg
Waiting for Wireless Events from interfaces...
16:00:07.970182   ath0     Set ESSID:"106F3F3D5224"
16:00:07.986767   ath0     Set Channel:0
16:00:08.001286   ath0     Set Mode:Master
16:00:08.015424   ath0     Set Encryption keyff
set Buffalo Capability = 00000009
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless11bg 1049[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless11bg_mac_limit
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless11bg_mac_limit 89[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_as_repeater
rc_as_repeath0: WDS Proirity mask Enable prio:3
ater.c(237) StartOfrc_as_repeater :as_repeater:[Start Repeater]
rc_as_repeater.c(322) StartOfrc_as_repeater :ina:[Start Pairent Mode]
ath0      extcmd:
ath1: WDS Proirity mask Enable prio:3
ath1      extcmd:
ath3: WDS Proirity mask Enable prio:3
ath3      extcmd:
MidLayerModDep.c(819) startModules :INFO:Started  module rc_as_repeater 48[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wireless_post
debug : Enter [BRCTL_ADD_RULE_IF]
add_if 00000100 ***************************
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wireless_post 35[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_nas
killall: hostapd: no process killed
MidLayerModDep.c(819) startModules :INFO:Started  module rc_nas 79[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_aoss_mssid
MidLayerModDep.c(819) startModules :INFO:Started  module rc_aoss_mssid 66[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ap_serv
Configuration file: /tmp/hostapd.conf_ath0
->setpid 0x47b080
pid: /var/run/hostapd.ath0.pid
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ap_serv 144[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanif_select
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_dhcpcd)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_0)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_1)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_2)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_3)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_4)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_pppoecd_50)
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_auto_detect)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanif_select 4[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanif
wanctl-lib.c(1369) CallIoctlOnEtherdeviceEx :ERR:!! Failed ioctl() !! ifr_name:[eth1] a_iCmd:[3509thresh62=33, thresh62_ext=33
3(-219)]:SIOCGIFADDR errorcode:126
Cannot assign requested address
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanif 1[msec]
thresh62=33, thresh62_ext=33
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pre
16:00:09.314676   ath0     Set Mode:Master
Using interface ath0 with hwaddr 10:6f:3f:3d:52:24 and ssid '106F3F3D5224'
Flushing old station entries
Deauthenticate all stations
l2_packet_receive - recvfrom: Network is down
l2_packet_receive - recvfrom: Network is down
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
et1: unit 1: phy 1 not up carrier
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
thresh62=33, thresh62_ext=33
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pre 3130[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect
thresh62=33, thresh62_ext=33
route: SIOC[ADD|DEL]RT: No such process
thresh62=33, thresh62_ext=33

s16 enet1 port1 up
et1: unit 1: phy 1 is up...
AG7240: enet WAN unit:0 is up. AG7240: done cfg2 0x7215 ifctl 0x0 miictrl  
thresh62=33, thresh62_ext=33
ch01: 5 pt
ch02: 11 pt
ch03: 5 pt
ch04: 0 pt
ch05: 0 pt
ch06: 0 pt
ch07: 0 pt
ch08: 1 pt
ch09: 3 pt
ch10: 1 pt
ch11: 3 pt
ch01: 17 pt ->Ch 1: 17
ch02: 17 pt ->Ch 2: 17
ch03: 11 pt ->Ch 3: 11
ch04: 4 pt ->Ch 4: 4
ch05: 1 pt ->Ch 5: 1
ch06: 0 pt ->Ch 6: 0
ch07: 0 pt ->Ch 7: 0
ch08: 2 pt ->Ch 8: 2
ch09: 3 pt ->Ch 9: 3
ch10: 3 pt ->Ch 10: 3
ch11: 3 pt ->Ch 11: 3
ch12: 2 pt ->ASS
ch13: 0 pt ->ASS
[20M]
ap_chansel_end: find channel 6 ch [00010080]
Country ie is DE
thresh62=33, thresh62_ext=33
ath_beacon_config.Configured SWBA :6,DMA resp time:4 for slotDur:100
16:00:13.424467   ath0     Scan request completed
wanctl-lib.c(1882) CheckDhcpClient :x:## START : Wait DHCP Client... 0 ##
wanctl-lib.c(1865) CheckDhcpClient :x:## don't get DHCP Client status ##
client.c(3126) SetAutoIP :eth1 set by AutoIP. ipaddr(169.254.34.90) netmask(255.255.0.0)
wanctl-lib.c(1882) CheckDhcpClient :x:## START : Wait DHCP Client... 1 ##
wanctl-lib.c(1847) CheckDhcpClient :x:## DHCP Client status = DHCP_BOUND##
wanctl-lib.c(1858) CheckDhcpClient :x:## Success : Found DHCP_BOUND Status ##
wanctl_dhcpcd.c(215) StoptDhcpcd :dhcpc-lock-debug:wanctl :Through StoptDhcpcd()
MidLayer.c(1591) ML_Signal_QueueRemove :x:SIGNAL-QUEUE NOT-FOUND (tree=NORM mod=rc_wanctl_dhcpcd)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect 7383[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_dummy
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_dummy 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_dhcpcd
wanctl-lib.c(1847) CheckDhcpClient :x:## DHCP Client status = DHCP_BOUND##
wanctl-lib.c(1858) CheckDhcpClient :x:## Success : Found DHCP_BOUND Status ##
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_dhcpcd 18[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_0
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_0 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_1
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_1 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_2
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_2 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_3
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_3 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_4
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_4 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_check
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_auto_detect_pppoecd_check 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_manual
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_manual 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_dhcpcd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_dhcpcd 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_0
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_0 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_1
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_1 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_2
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_2 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_3
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_3 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_4
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_4 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoecd_check
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoecd_check 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanif_modem
rc_wanif_modem.c(44) StartOfrc_wanif_modem :x:SKIP Module module (StartOfrc_wanif_modem)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanif_modem 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_modem_detect
rc_wanctl_modem_detect.c(108) StartOfrc_wanctl_modem_detect :x:SKIP Module module (StartOfrc_wanctl_modem_detect)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_modem_detect 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_modem_detect_dummy
rc_wanctl_modem_detect_dummy.c(88) StartOfrc_wanctl_modem_detect_dummy :x:SKIP Module module (StartOfrc_wanctl_modem_detect_dummy)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_modem_detect_dummy 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_ppp_modem
rc_wanctl_ppp_modem.c(290) StartOfrc_wanctl_ppp_modem :x:SKIP Module module (StartOfrc_wanctl_ppp_modem)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_ppp_modem 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_post
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_post 157[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wanctl_pppoeroute
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wanctl_pppoeroute 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_dnrd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_dnrd 19[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_netwatchd
wanctl_dhcpcd.c(52) StartDhcpcd :dhcpc-lock-debug:wanctl : Through StartDhcpcd()
wanctl-wanstate_check.c(910) wanstate_check_main :wanctl:Start wanstate_check Daemon
MidLayerModDep.c(819) startModules :INFO:Started  module rc_netwatchd 220[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter
iptables: Bad rule (does a matching rule exist in that chain?)
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter 693[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_simple
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_simple 69[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_user
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_user 1[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ipfilter_p p t p
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ipfilter_p p t p 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_nat
Using /lib/modules/kernel/net/ipv4/netfilter/ip_conntrack_p p t p.ko
ip_conntrack_p p t p version 3.1 loaded
Using /lib/modules/kernel/net/ipv4/netfilter/ip_nat_p p t p.ko
ip_nat_p p t p version 3.0 loaded
MidLayerModDep.c(819) startModules :INFO:Started  module rc_nat 198[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_routectl
MidLayerModDep.c(819) startModules :INFO:Started  module rc_routectl 49[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_lltd
MidLayerModDep.c(819) startModules :INFO:Started  module rc_lltd 72[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wsc
Execute wscconfig init
SAMPLE!!
Execute wscconfig stop
Execute wscconfig start
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wsc 246[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_upnp
iptables v1.3.5: Couldn't find target `UPNP-PREROUTING-CHAIN'

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables v1.3.5: Couldn't find target `UPNP-POSTROUTING-CHAIN'

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
MidLayerModDep.c(819) startModules :INFO:Started  module rc_upnp 468[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_movie_engine
wlctl-ath.c(3567) wlconf_chg_movie_engine_profile :x:MOVIE_ENGINE_MODE_OFF
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 0.3.1d, April 24 2006
*********************************************
mcsnoop_br_ioctl_device:239: mcast_maxage 300000 / 1000
ath0      extcmd:
ath0      extcmd:
set Buffalo Capability = 00000009
ath0      extcmd:
ath1      extcmd:
ath1      extcmd:
set Buffalo Capability = 00000009
ath1      extcmd:
ath2      extcmd:
ath2      extcmd:
set Buffalo Capability = 00000009
ath2      extcmd:
ath3      extcmd:
ath3      extcmd:
set Buffalo Capability = 00000009
ath3      extcmd:
wlctl-ath.c(3407) wlconf_modified_reset_paththrow :xIPv6) AS_BEHAVIOR_MODE_ROUTER
debug : Enter [BRCTL_ADD_IF]
MidLayerModDep.c(819) startModules :INFO:Started  module rc_movie_engine 531[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_ntpclient
MidLayerModDep.c(819) startModules :INFO:Started  module rc_ntpclient 36[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_eco
MidLayerModDep.c(819) startModules :INFO:Started  module rc_eco 142[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_wan_qos
MidLayerModDep.c(819) startModules :INFO:Started  module rc_wan_qos 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_p p t p_server
MidLayerModDep.c(819) startModules :INFO:Started  module rc_p p t p_server 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_p p t p_server_route
/dev/set_clock: cannot create
MidLayerModDep.c(819) startModules :INFO:Started  module rc_p p t p_server_route 172[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_nastorage
MidLayerModDep.c(819) startModules :INFO:Started  module rc_nastorage 4[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_auto_fwup
MidLayerModDep.c(819) startModules :INFO:Started  module rc_auto_fwup 48[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_end_signal
MidLayerModDep.c(819) startModules :INFO:Started  module rc_end_signal 12[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_timer_reboot
MidLayerModDep.c(819) startModules :INFO:Started  module rc_timer_reboot 0[msec]
MidLayerModDep.c(807) startModules :INFO:Starting module rc_dst_timer
MidLayerModDep.c(819) startModules :INFO:Started  module rc_dst_timer 0[msec]
led_mask_11g_chip:f0
reg:000000B0 [CC35CC35 --> CC35CC35]
reg:000000B4 [CA35CA35 --> CA35CA35]
reg:000000B8 [C935C935 --> C935C935]
wanctl_fwupdate.c(191) GetFirmwareListFromInternet EBUG:pUrl:http://buffalo.jp/download/drive ... r_hp_g300nh2_ch.txt
wanctl-lib.c(3742) GetDataFromInternet EBUG:parse_url start
wanctl-lib.c(3744) GetDataFromInternet EBUG:parse_url end
wanctl-lib.c(3747) GetDataFromInternet EBUG:server.host : buffalo.jp
wanctl-lib.c(3748) GetDataFromInternet EBUG:target.path : download/driver/lan/autoup/wzr_hp_g300nh2_ch.txt
wanctl-lib.c(3754) GetDataFromInternet EBUG:lookup_host start
wanctl-lib.c(3518) GetHostByNameWithTimeOut EBUG:Waiting for GetHostByName's End... 0
cannot open connection to btpd in //.btpd (No such file or directory).
killall: twonkymedia: no process killed
killall: twonkymediaserver: no process killed
rc_nastorage.c(2571) NastorageStop_BitTorrent2 :x:btpd STOP-SUCCESS (0 sec)
rcUtil_usb.c(2643) UsbStorageInfo_Update :x:UsbStorageInfo_Update
MidLayerLEDSW.c(2278) MLLE_WaitSwitch :x:Modified Movie Engine Switch
wlctl-ath.c(3567) wlconf_chg_movie_engine_profile :x:MOVIE_ENGINE_MODE_OFF
mcsnoop_br_ioctl_device:239: mcast_maxage 300000 / 1000
Initializing stack... OK
Now starting stack
wanctl-lib.c(3518) GetHostByNameWithTimeOut EBUG:Waiting for GetHostByName's End... 1
main.c(280) main :xMLIST RESTORE START
main.c(283) main :xMLIST RESTORE END
wanctl-lib.c(3759) GetDataFromInternet EBUG:lookup_host end
wanctl-lib.c(3760) GetDataFromInternet EBUG:server.host : buffalo.jp
wanctl-lib.c(3761) GetDataFromInternet EBUG:target.path : download/driver/lan/autoup/wzr_hp_g300nh2_ch.txt
DEVICE PIN: 38489662

******* MODE: AP with built-in Registrar and UPnP Proxy *******

checking for PUSH BUTTON
devpwd is not setted, but start InitiateRegistrarion.
Waiting for Client to connect(using IEs)...
ath0      extcmd:
ath0      extcmd:
set Buffalo Capability = 00000009
ath0      extcmd:
ath1      extcmd:
ath1      extcmd:
set Buffalo Capability = 00000009
ath1      extcmd:
ath2      extcmd:
wanctl_fwupdate.c(193) GetFirmwareListFromInternet EBUG:GetDataFromInternet Success.
wanctl_fwupdate.c(532) CheckFirmupThreshold :x:version down limit over ver=1.80
wanctl_fwupdate.c(532) CheckFirmupThreshold :x:version down limit over ver=1.79
ath2      extcmd:
set Buffalo Capability = 00000009
ath2      extcmd:
ath3      extcmd:
ath3      extcmd:
set Buffalo Capability = 00000009
ath3      extcmd:
wlctl-ath.c(3407) wlconf_modified_reset_paththrow :xIPv6) AS_BEHAVIOR_MODE_ROUTER
debug : Enter [BRCTL_ADD_IF]
ARPING to 192.168.11.1 from 192.168.11.1 via br0
Sent 1 probes (1 broadcast(s))
Received 0 reply


本帖子中包含更多资源

您需要 登录 才可以下载或查看，没有账号？立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

xcb***
 楼主| | 显示全部楼层
希望这次升级过程对大家有所帮助
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

shen***
| 显示全部楼层
发个openwrt编程器固件吧
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

gong***
来自手机 | 显示全部楼层
楼主，帮我一下
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

返回列表 发新帖
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-28 08:09

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱：js12377 | @jischina.com.cn 举报电话：025-88802724 本站不良内容举报信箱：68610888@qq.com 举报电话：0519-86695797

快速回复 返回顶部 返回列表