求各位神仙帮我看看这个华为K662c怎么搞？

zk***

Chip Type is SD5117P
safetycode boot type: spi nand flash
start auth startcode
InitMemoryManager.
InitMemoryManager.
Select startcodeA
PdtCerSize:0x512, PdtCerOffset:0x1134620c
InitMemoryManager.
vertify_data_by_cert der in .
ParseAsnToX509Cert in
ParseAsnToX509Cert_TBSC in
ParseAsnToX509Cert_TBSC out
ParseAsnToX509Cert out
CertSignVerify ok
InitMemoryManager.
vertify_data_by_cert_ex in .
get_rsa_by_pdt_cert_struct in .
get_rsa_by_pdt_cert_struct out .
CertSignVerify ok
Start in Statcode
startcode uboot boot count:-1431655766
Start in Safe Mode
Use the AllsytemA to load success
End out startcode

DRAM:  256 MiB
Real DDR Size: 268435456
Boot From SPI NAND flash
Chip Type is SD5117P
NAND:  SPI_NAND_FLASH_TYPE
flash_type = [0x6]
Special Nand id table Version 1.23
Nand ID: 0xC8 0xD9 0xC8 0xD9 0xC8 0x00 0x00 0x00
now using default nand flash type, Block:128KB Page:2KB!
Default flash solution!
ECC Match pagesize:2K, oobzie:64, ecctype:8bit,mtd->size:0x0
Nand(Hardware): Block:128KB Page:2KB Chip:536870912B OOB:64B ECC:8bit
512 MiB
512 MiB
[UBI-DEBUG]: all in ubi mode
In:    serial
Out:   serial
Err:   serial
Net:   PHY power down !!!
Read test request info fail: blockid:0x9, magic:0x23494255
Request info size 0x80000 is out of 0x1000
Read test request info fail: blockid:0x9, magic:0x23494255
Request info size 0x80000 is out of 0x1000
ret=1, Mbist test_request=0x0
Read test request info fail: blockid:0x9, magic:0x23494255
Request info size 0x80000 is out of 0x1000
UBI: attaching mtd2
ubi0 error: ubi_compare_lebs: unsupported on-flash UBI format
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd2, error -22
UBI: attaching mtd2
ubi0 error: ubi_compare_lebs: unsupported on-flash UBI format
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd2, error -22
UBI: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "ubifs", size 127 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 1015, bad PEBs: 1, corrupted PEBs: 0
ubi0: user volume: 10, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 11/5, WL threshold: 4096, image sequence number: 251994937
ubi0: available PEBs: 0, total reserved PEBs: 1015, PEBs reserved for bad PEB handling: 24
Start from main system(0x0)!
CRC:0x9789603f, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x2
close uboot pcie
5117P or 5117v  pcie power is closed
5117P or 5117v or 5117L pcie&wifi power is closed
Main area: Cert partition Found
Slave area: Cert partition Found
Main area (A) is OK!
CRC:0x39e1f1ae, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x2
real_ddr_size: 268435456/256M

Match the dtb file index : 7!
   XIP Kernel Image ... OK

Starting kernel ...

[    0.000000] smp_twd: clock not found -2
[    0.159783] of_amba_device_create(): amba_device_add() failed (-2) for /sysctl@10100000
[    0.160114] of_amba_device_create(): amba_device_add() failed (-2) for /timer01@10104000
[    0.161624] L2C: device tree omits to specify unified cache
[    0.161677] L2C-310: enabling full line of zeros but not enabled in Cortex-A9
[    0.272003] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.797526] ubi0 error: ubi_compare_lebs: unsupported on-flash UBI format
[    1.804708] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd1, error -22
[    1.811782] UBI error: cannot attach mtd1
[    1.816835] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.825071] CPU1: stopping
[    1.827780] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G        W       4.4.197 #1
[    1.834969] Hardware name: Hisilicon A9
[    1.838827] [<c0012d5c>] (rtos_unwind_backtrace) from [<c000e52c>] (show_stack+0x10/0x14)
[    1.846989] [<c000e52c>] (show_stack) from [<c023ccc0>] (dump_stack+0x88/0xa8)
[    1.854190] [<c023ccc0>] (dump_stack) from [<c00119a4>] (handle_IPI+0x330/0x514)
[    1.861559] [<c00119a4>] (handle_IPI) from [<c00094b8>] (gic_handle_irq+0x70/0x78)
[    1.869103] [<c00094b8>] (gic_handle_irq) from [<c000efc0>] (__irq_svc+0x40/0x54)
[    1.876552] Exception stack(0xcefcdf98 to 0xcefcdfe0)
[    1.881585] df80:                                                       00000000 00003c9a
[    1.889732] dfa0: cf49e544 c0019a60 ffffe000 55555555 c040e798 cefcdff8 c05d6564 414fc091
[    1.897876] dfc0: 00000000 00000000 00000000 cefcdfe8 c000b604 c000b5f4 60000013 ffffffff
[    1.906027] [<c000efc0>] (__irq_svc) from [<c000b5f4>] (arch_cpu_idle+0x1c/0x38)
[    1.913404] [<c000b5f4>] (arch_cpu_idle) from [<c0062e74>] (cpu_startup_entry+0x268/0x2bc)
[    1.921638] [<c0062e74>] (cpu_startup_entry) from [<80909558>] (0x80909558)
[    1.928577] Rebooting in 1 seconds..
[    2.928616] l2cache_base NULL
[    4.924622] reboot fail!Waiting for watchdog reset ...

TTL中断不了，现在只亮一个电源灯了，有线无线都不能启动。只能上编程器了吗？哪位大神有这个编程器固件有偿买个？

ak***

到海鲜市场找人修