中兴 F657GV9 求一个备份固件 分享653GV9 -MDT0固件

iotdoc

中兴 F657GV9 求一个备份固件  想用F653GV9刷一下 看看 能不能刷成联通的 ，谢谢了！


插上U盘 按照下面备份哈，我想测试刷联通
分区备份操作地址
cat /proc/mtd
cat /dev/mtd0 > /mnt/usb1_1/0-whole_flash.bin
cat /dev/mtd1 > /mnt/usb1_1/1-u-boot.bin
cat /dev/mtd2 > /mnt/usb1_1/2-others.bin
cat /dev/mtd3 > /mnt/usb1_1/3-parameter_tags.bin
cat /dev/mtd4 > /mnt/usb1_1/4-wlan.bin
cat /dev/mtd5 > /mnt/usb1_1/5-usercfg.bin
cat /dev/mtd6 > /mnt/usb1_1/6-middle.bin
cat /dev/mtd7 > /mnt/usb1_1/7-kernel1.bin
cat /dev/mtd8 > /mnt/usb1_1/8-kernel2.bin
cat /dev/mtd9 > /mnt/usb1_1/9-osgi1.bin
cat /dev/mtd10 > /mnt/usb1_1/10-osgi2.bin
cat /dev/mtd11 > /mnt/usb1_1/11-plugin_data.bin
cat /dev/mtd12 > /mnt/usb1_1/12-rootfs.bin

分享F653GV9固件 MDT0编程器固件 以及  MDT7-10固件

/ # upgradetest getver
Main  version num: V2.2.0P1N43
Spare version num: V2.2.0P1N43




Boot SPI NAND
start read bootheader
start read secondboot
non secure boot
Jump
rate is 1066M
value = 0x12
7smux:3f7ffffa:3ffffeff:19ff0555:6be1b
7s vid 112
vid is 112
ddr size 20000000


U-Boot 2013.04 (Sep 14 2021 - 09:05:33)

CPU  : ZX279127S@A9,1000MHZ
Board: ZXIC zx279127sevb
127s product_vid = 112
DRAM:  512 MiB
127s product_vid = 112
,20000000,60000000
cpuid=27912710
127s pinmux: 3f7ffffa  3ffffeff  19ff0555  6be1b
127s product_vid = 112
mtk reset,66,53
bootsel=3
NAND:
Manu ID: 0x2c, Chip ID: 0x24 (Micron SPI NAND MT29F2G01ABAGDWB  256MiB 3,3V)
256 MiB
<nand_read_skip_bad_,422>!mtdpart=0x1,offset=0x0,mtdpartoffset=0x180000,mtdPartsize=0x80000,length=0x20000
In:    serial
Out:   serial
Err:   serial
clk_pll env is not setted, core clk won't change
Net:   enter ref_clk_set.. mode = 0 .
enter pll_cfg_fractional
ref_clk_set success!
gpon serdes init
addr 0x9400002c before value is 11000013
addr 0x9400004c after value is 11003ff3
eth0

Hit 1 to upgrade software version
Hit any key to stop autoboot:  0
addr=1a00000
addr=3a00000
select=0x0
search=0x2
<nand_read_skip_bad_,422>!mtdpart=0x6,offset=0x0,mtdpartoffset=0x200000,mtdPartsize=0x400000,length=0x1000
tmp=0x00000000, value=0
select=0x0
search=0x2
search->result[0].entry=1a00140
<nand_read_skip_bad_,422>!mtdpart=0x2,offset=0x0,mtdpartoffset=0x1a00000,mtdPartsize=0x2000000,length=0x1a20000
classstr: ZXHN, hwstr: CMCC, prostr: UNI, verstr: V2.2.0P1N43

---mtdparts_init--current_mtd_partnum=0-
dev id: type = 2, num = 0, size = 0xffffffff, mtd_id = single part
part  : name = rootfs0, size = 0x01a00000, offset = 0x01a20000
part  : name = rootfs1, size = 0x01a00000, offset = 0x03a20000

--- jffs2_part_info: partition number 0 for device nand0 (single part)
jffs2_part_info:rootfs0,1a20000
### JFFS2 loading '0uImage' to 0x44000000
Scanning JFFS2 FS: ................ done.
### JFFS2 load complete: 4308543 bytes loaded to 0x44000000
127s product_vid = 112
<nand_read_skip_bad_,422>!mtdpart=0x0,offset=0x0,mtdpartoffset=0x0,mtdPartsize=0x180000,length=0x80000
lseek=0x4207a000
cmdline=U-Boot V1.1.3 20210606211658
output gpio:58, value=1, 0
output gpio:59, value=1, 0
## Booting kernel from Legacy Image at 44000000 ...
   Image Name:   Linux Kernel Image
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4308479 Bytes = 4.1 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
----------------------
|-->setup versioninfo tag...

Starting kernel ...

tm5880891

刷联通我早就成了，不是像你这么搞，你这样不启动

iotdoc

就是想刷个联通固件当联通用，你这肯定要钱。不是商家就是自己玩玩划不来。?

iotdoc

tm5880891 发表于 2023-5-8 22:43
刷联通我早就成了，不是像你这么搞，你这样不启动

我想着全部替换，不行就是玩玩，你这指导要钱?我不是商家，就是玩玩。这猫想搞个桥接用放弱电箱刚好

tm5880891

shape 发表于 2023-5-8 22:54
我想着全部替换，不行就是玩玩，你这指导要钱?我不是商家，就是玩玩。这猫想搞个桥接用放弱电箱刚好 ...

你全替换也没作用，甚至有的替换后你猫会坏，不信你试试