|
|
楼主 |
发表于 2023-5-29 12:43
|
显示全部楼层
3: Boot system code via Flash (default).
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
6: System Enter UBoot to Update Img or Bin.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
[SERIAL-TRACE] : COMM-EVENT [tx]
You choosed 3
0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4822305 Bytes = 4.6 MB
Load Address: 80000000
Entry Point: 8000c310
raspi_read: from:50040 len:499521
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (zhangzhimei@wireless) (gcc version 3.4.2) #141 Thu Sep 20 12:00:39 CST 2018
The CPU feqenuce set to 580 MHz
MIPS CPU sleep mode enabled.
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0003c00e
Readback ErrCtl register=0003c00e
Memory: 59620k/65536k available (4175k kernel code, 5916k reserved, 779k data, 160k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:804bfcf8, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 1a311c
RALINK_GPIOMODE = 18311c
PPLL_CFG1=0xe94000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0
*************** MT7620 PCIe RC mode *************
bio: create slab <bio-0> at 0
SCSI subsystem initialized
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [io disabled]
pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
pci 0000:00:00.0: bridge window [mem pref disabled]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20100000
res[0]->end = 201fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 116
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
RALINK_REG_PIODATA=00fc7f87
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
loop: module loaded
deice id : c2 20 17 c2 20 (2017c220)
[2015c220 :2017c220][weight:00020000][2016c220 :2017c220][weight:00010000]MX25L6405D(c2 2017c220) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x0000001d2561 : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
i=26, one click[2800]
0x0000001d2561-0x000001000000 : "RootFS"
mtd: partition "RootFS" extends beyond the end of device "raspi" -- size truncated to 0x62da9f
i=25, one click[2800]
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x000000050000-0x000001000000 : "Kernel_RootFS"
mtd: partition "Kernel_RootFS" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
SMACCR1 -- : 0x00003c1e
SMACCR0 -- : 0x04646945
Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x00003c1e
SMACCR0 -- : 0x04646945
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
p p t p driver version 0.8.5
=== pAd = c0045000, size = 947960 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.2.0_edcca
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (931 buckets, 3724 max)
ctnetlink v0.93: registering with nfnetlink.
nf_conntrack_rtsp v0.6.21 loading
nf_conntrack_ipsec loaded
PortalManage Module: Load ...
PortalManage Module: Load Success
matchsize=264
xt_time: kernel timezone is -0000
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
---->luotao ipport netspy test Driver.....-->
NETSPY IPPORT proc module 1.0 initialized
GRE over IPv4 demultiplexor driver
gre: can't add protocol
nf_nat_rtsp v0.6.21 loading
nf_nat_ipsec loaded
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 160k freed
init started: BusyBox v1.12.1 (2018-09-20 08:40:05 CST)
starting pid 32, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Tue Jan 1 00:00:00 UTC 2013
devpts: called with bogus options
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
=System Architecture Department=
starting pid 48, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2018-09-20 08:40:05 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
# [goahead]:trace[0]:internet.sh
internet.sh
Internet cli_mode=
chpasswd: warning: cannot lock '/etc/passwd': Permission denied
Password for 'Admin' changed
rmmod: ralink_wdt: No such file or directory
rmmod: cls: No such file or directory
rmmod: hw_nat: No such file or directory
rmmod: raeth: No such file or directory
insmod: can't read '-q': No such file or directory
insmod: can't read '-q': No such file or directory
insmod: can't read '-q': No such file or directory
##### disable 1st wireless interface #####
##### disable 2nd wireless interface #####
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
insmod: can't read '-q': No such file or directory
xxxxxxxxxxxxxx insmod -q MT7610_ap xxxxxxxxxxxxxxx
register rtpci
=== pAd = c0682000, size = 1304088 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0580000, csr_addr=0xc0580000!
device_id =0x7650
==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
MACVersion = 0x76502000
RX DESC a3eda000 size = 4096
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff20
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 1, D2 = 10, CalCode = 21 !!!
RT6352_Temperature_Init : BBPR49 = 0x1
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff7
Current Temperature from BBP_R49=0xfffffff6
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= e, phase= 0)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 0, phase= 2)
TX IQ Calibration Done!
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
Main bssid = 3c:1e:04:64:69:46
<==== rt28xx_init, Status=0
0x1300 = 00064380
load fw spent 16ms
RX DESC a3659000 size = 2048
RX1 DESC a365a000 size = 2048
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
1. Phy Mode = 49
2. Phy Mode = 49
drivers/net/wireless/MT7610_ap/chips/mt76x0.c:2206 assert (pAd->TxPower[choffset].Channel == 36)failed
ext_pa_current_setting = 1
TXALC> bInternalTxALC = 0
3. Phy Mode = 49
AntCfgInit: primary/secondary ant 0/1
ChipStructAssign(): RALINK6590 hook !
MCS Set = ff 00 00 00 01
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
Main bssid = 3c:1e:04:64:69:47
<==== rt28xx_init, Status=0
SYNC - BBP R4 to 20MHz.l
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=149, HT-CentCh=151, VHT-CentCh=155
APStartUp(): AP Set CentralFreq at 155(Prim=149, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2)
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
0x1300 = 00064380
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
<<<<<<<<<<<<<<<< WEB URL FILTER >>>>>>>>>>>>>>>>>>>>>
rule null!!!!
<<<<<<<<<<<<<<<< VIRTUAL SERVER ADN DMZ SET >>>>>>>>>>>>>>>>>>>>
virtual server init!!!
ifconfig: eth2.2: error fetching interface information: Device not found
<<<<<<<<<<<<<<<<<<< ALG virtual** >>>>>>>>>>>>>>>>>>>>>
------Enable sip ALG function!------ [net/netfilter/nf_conntrack_sip.c proc_debug_write_sip 154]
------Enable p p t p ALG function!------ [net/netfilter/nf_conntrack_p p t p.c proc_debug_write_p p t p 659]
------Enable p p t p ALG function!------ [net/netfilter/nf_conntrack_p p t p.c proc_debug_write_p p t p 659]
------Enable l2tp ALG function!------ [net/netfilter/nf_conntrack_l2tp.c proc_debug_write_l2tp 86]
------Enable l2tp ALG function!------ [net/netfilter/nf_conntrack_l2tp.c proc_debug_write_l2tp 86]
------Enable ipsec ALG function!------ [net/netfilter/nf_conntrack_ipsec.c proc_debug_write_ipsec 212]
------Enable ipsec ALG function!------ [net/netfilter/nf_conntrack_ipsec.c proc_debug_write_ipsec 212]
<<<<<<<<<<<<<<<< ACL SET >>>>>>>>>>>>>>>>>>>>
acl init!!!
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
Raeth v3.0 (Tasklet,SkbRecycle)
phy_tx_ring = 0x0290e000, tx_ring = 0xa290e000
phy_rx_ring0 = 0x0290f000, rx_ring0 = 0xa290f000
SMACCR1 -- : 0x00003c1e
SMACCR0 -- : 0x04646945
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20010000
vconfig: ioctl error for rem: No such device
vconfig: ioctl error for rem: No such device
rmmod: 8021q: No such file or directory
insmod: can't read '-q': No such file or directory
device eth2 entered promiscuous mode
##### config Ralink ESW vlan partition (WLLLL) #####
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10002
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write ofdevice ra0 entered promiscuous mode
fset=2414, value=10001
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
##### enable 1st wireless interface #####
device eth2.1 entered promiscuous mode
device rai0 entered promiscuous mode
##### enable 2nd wireless interface #####
[wan.sh]: info
[nat.sh]: info
[hw_nat.sh]: info
rmmod: hw_nat: No such file or directory
hw_nat: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Ralink HW NAT Module Enabled
[wan.sh]:
[wan.sh]wait for pppd 0 second.
[udhcpc]: info, udhcp client (v0.9.9-pre) started
[udhcpc]: info, adapter index 10
[udhcpc]: info, adapter hardware address 3c:1e:04:64:69:48
[udhcpc]: info, execle'ing /sbin/udhcpc.sh
[udhcpc]: deconfig
br0: port 3(rai0) entering learning state
br0: port 3(rai0) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
(none)
rm: cannot remove '/var/portmapinfo.conf': No such file or directory
[udhcpc]: info, entering raw listen mode
[udhcpc]: info, Opening raw socket on ifindex 10
[udhcpd]: wait for /dev/urandom times=1
br0: port 3(rai0) entering forwarding state
br0: port 2(eth2.1) entering forwarding state
br0: port 1(ra0) entering forwarding state
killall: udhcpd: no process killed
[udhcpd]: info, udhcp server (v0.9.9-pre) started
[udhcpd]: info, Attaching option subnet to list
[udhcpd]: info, Attaching option dns to list
[udhcpd]: info, Attaching option dns to existing member of list
[udhcpd]: info, Attaching option router to list
[udhcpd]: info, Attaching option lease to list
[udhcpd]: error, max_leases value (254) not sane, setting to 253 instead
[udhcpd]: info, Read 0 leases
[udhcpd]: info, br0 (our ip) = 192.168.0.1
[udhcpd]: info, adapter index 11
[udhcpd]: info, adapter hardware address 3c:1e:04:64:69:45
[udhcpd]: info, Opening listen socket on 0x00000000:67 br0
Set: phy[4].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[4].reg[0] = 3300
Set: phy[1].reg[0] = 3300
Set: phy[2].reg[0] = 3300
Set: phy[3].reg[0] = 3300
igmpproxy, Version 0.1 beta2, Build 180920
Copyright 2005 by Johnny Egeland <johnny@rlo.org>
Distributed under the GNU GENERAL PUBLIC LICENSE, Version 2 - check GPL.txt
Warn: Warning, No upstream interface assigned.
<<<<<<<<<<<<<<<< PORTAL MANAGER >>>>>>>>>>>>>>>>>>>>
not enable portal manage!!!
<<<<<<<<<<<<<<<< PORTAL MANAGER >>>>>>>>>>>>>>>>>>>>
not enable portal manage!!!
echo 1 > /proc/sys/net/ipv4/ip_forward
iwpriv ra0 set IgmpSnEnable=1
iwpriv rai0 set IgmpSnEnable=1
mdev: mknod loop0: Read-only file system
[goahead]:trace[0]:killall rt2860apd 1>/dev/null 2>&1
killall rt2860apd 1>/dev/null 2>&1
[goahead]:trace[0]:killall rtinicapd 1>/dev/null 2>&1
killall rtinicapd 1>/dev/null 2>&1
[goahead]:trace[0]:ntp.sh
ntp.sh
[goahead]:trace[0]:ddns.sh
ddns.sh
[goahead]:trace[0]:iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
[goahead]:trace[0]:iwpriv ra0 set WscConfMode=7
iwpriv ra0 set WscConfMode=7
[goahead]:trace[0]:route add -host 239.255.255.250 dev br0 1>/dev/null 2>&1
route add -host 239.255.255.250 dev br0 1>/dev/null 2>&1
[goahead]:trace[0]:wscd -m 1 -a 192.168.0.1 -i ra0 &
wscd -m 1 -a 192.168.0.1 -i ra0 &
[goahead]:trace[0]:iwpriv rai0 set WscConfMode=0 1>/dev/null 2>&1
iwpriv rai0 set WscConfMode=0 1>/dev/null 2>&1
sh: wscd: not found
[goahead]:trace[0]:iwpriv rai0 set WscConfMode=7
iwpriv rai0 set WscConfMode=7
[goahead]:trace[0]:route add -host 239.255.255.250 dev br0 1>/dev/null 2>&1
route add -host 239.255.255.250 dev br0 1>/dev/null 2>&1
[goahead]:trace[0]:wscd -m 1 -a 192.168.0.1 -i rai0 &
wscd -m 1 -a 192.168.0.1 -i rai0 &
[goahead]:trace[0]:killall -q klogd
killall -q klogd
sh: wscd: not found
[goahead]:trace[0]:killall -q syslogd
killall -q syslogd
[goahead]:trace[0]:syslogd -C4 1>/dev/null 2>&1
syslogd -C4 1>/dev/null 2>&1
[goahead]:trace[0]:klogd 1>/dev/null 2>&1
klogd 1>/dev/null 2>&1
[154:ip_control_init()]=>enter.
[goahead]:trace[0]:ip_qos
ip_qos
tc qdisc del dev eth2.2 root 1>/dev/null 2>&1
tc qdisc del dev br0 root 1>/dev/null 2>&1
iptables -t mangle -D PREROUTING -j qos_mangle_upload 1>/dev/null 2>&1
iptables -t mangle -F qos_mangle_upload 1>/dev/null 2>&1
iptables -t mangle -X qos_mangle_upload 1>/dev/null 2>&1
iptables -t mangle -D POSTROUTING -j qos_mangle_download 1>/dev/null 2>&1
iptables -t mangle -F qos_mangle_download 1>/dev/null 2>&1
iptables -t mangle -X qos_mangle_download 1>/dev/null 2>&1
hw_nat.sh
[hw_nat.sh]: info
Ralink HW NAT Module Disabled
Ralink HW NAT Module Enabled
[goahead]:trace[4] B: Registering database table <users>
[goahead]:trace[4]B: Registering database table <groups>
[goahead]:trace[4]B: Registering database table <access>
[goahead]:trace[3]:UM: Adding group <adm>
[goahead]:trace[5]B: Adding a row to table <groups>
[goahead]:E_LOG :gohead.c: Warning: empty administrator account or password
gohead.c: Warning: empty administrator account or password
[goahead]:trace[0]:webs: Listening for HTTP requests at address 192.168.0.1
webs: Listening for HTTP requests at address 192.168.0.1
[goahead]:trace[0]:sh /var/iptables_filter_rules.sh
sh /var/iptables_filter_rules.sh
iptables: No chain/target/match by that name.
[SERIAL-TRACE] : COMM-EVENT [tx]
|
|
/1 
IP卡
狗仔卡
发表于 2023-5-29 12:21
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
