小米路由器HD 刷了openwrt恢复官固变砖重启怎么办

wantknow

U-Boot 2012.07 [ ,unknown] (Mar 22 2017 - 15:09:03)

smem ram ptable found: ver: 0 len: 5
DRAM:  494 MiB
NAND:  SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
PCI0 Link Intialized
PCI1 Link Intialized
In:    serial
Out:   serial
Err:   serial
cdp: get part failed for 0:HLOS
cdp: get part failed for rootfs
Net:   MAC1 addr:28:6c:7:69:6d:b6
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init  done
MAC2 addr:28:6c:7:69:6d:b7
eth0, eth1
Hit any key to stop autoboot:  0
Boot failure detected on both systems
Verifying kernel1 uImage CRC, offset: 0x800000

NAND read: device 0 offset 0x800000, size 0x400000
4194304 bytes read: OK

## Checking Image at 44000000 ...
   Legacy image found
   Image Name:   MIPS OpenWrt Linux-3.10.14
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3419055 Bytes = 3.3 MiB
   Load Address: 82001000
   Entry Point:  8246c190
   Verifying Checksum ... OK

NAND read: device 0 offset 0x800000, size 0x400000
4194304 bytes read: OK
   Image Name:   MIPS OpenWrt Linux-3.10.14
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3419055 Bytes = 3.3 MiB
   Load Address: 82001000
   Entry Point:  8246c190
   Verifying Checksum ... OK
Unimplemented compression type 3
Erasing Nand...
Erasing at 0x520000 -- 100% complete.
Writing to Nand... done
resetting ...

Resetting with watch dog!

小溦

你刷的是r3p固件吧。串口刷内核吧

wantknow

小溦 发表于 2023-6-2 22:10
你刷的是r3p固件吧。串口刷内核吧

有什么教程呢？ 出来的uboot 没有选择，全靠命令

wantknow

uboot的help提升有这些命令，该怎么办呢
ar8xxx_dump- Dump ar8xxx registers
base    - print or set address offset
bootm   - boot application image from memory
bootmiwifi- boot MiWiFi boards from flash device
bootp   - boot image via network using BOOTP/TFTP protocol
bootz   - boot Linux zImage image from memory
chpart  - change active partition
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
dhcp    - boot image via network using DHCP/TFTP protocol
echo    - echo args to console
env     - environment handling commands
ethspeed- Force ethernet speed to 10/100/autoneg
exit    - exit script
false   - do nothing, unsuccessfully
fdt     - flattened device tree utility commands
fuseipq - fuse QFPROM registers from memory

go      - start application at address 'addr'
help    - print command description/usage
i2c     - I2C sub-system
iminfo  - print header information for application image
imxtract- extract a part of a multi-image
ipq_nand- Switch between SBL and Linux kernel page layout.
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
smeminfo- print SMEM FLASH information
source  - run script from memory
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
true    - do nothing, successfully
uartrd  - uartrd from flash device
uartwr  - uartwr from flash device
ubi     - ubi commands
version - print monitor, compiler and linker version

w94ini

我关心刷完openwrt可以正常使用不？怎么刷的，我去试一试