[已解决]沛喆 PZ-L5 接上 TTL 刷入 集客AX1800H 固件后无限重启

fej***

前一阵子看到论坛贴子：沛喆PZ-L5可以刷集客AX1800H

尝试了刷机，翻了车

大佬们看看是什么地方操作错了，指导指导

mtkautoboot 启动菜单里边选择了

2. Upgrade firmware


最后从 tftp 传输 集客AX1800H 固件刷入

1. => mtkautoboot   
   
2. 
   
3.   *** U-Boot Boot Menu ***
   
4. 
   
5.      1. Startup system (Default)
   
6.      2. Upgrade firmware
   
7.      3. Upgrade bootloader
   
8.      4. Upgrade bootloader (advanced mode)
   
9.      5. Load image
   
10.      0. U-Boot console
    
11. 
    
12. 
    
13.   Press UP/DOWN to move, ENTER to select
    
14. 
    
15. *** Upgrading Firmware ***
    
16. 
    
17. Available load methods:
    
18.     0 - TFTP client (Default)
    
19.     1 - Xmodem
    
20.     2 - Ymodem
    
21.     3 - Kermit
    
22.     4 - S-Record
    
23. 
    
24. Select (enter for default):
    
25. 
    
26. Input U-Boot's IP address: 192.168.168.14
    
27. Input TFTP server's IP address: 192.168.168.4
    
28. Input IP netmask: 255.255.255.0
    
29. Input file name: AX1800.bin
    
30. 
    
31. Using eth@1e100000 device
    
32. TFTP from server 192.168.168.4; our IP address is 192.168.168.14
    
33. Filename 'AX1800.bin'.
    
34. Load address: 0x80010000
    
35. Loading: T #################################################################
    
36.          #################################################################
    
37.          #################################################################
    
38.          #################################################################
    
39.          #################################################################
    
40.          #################################################################
    
41.          #################################################################
    
42.          #
    
43.          1.1 MiB/s
    
44. done
    
45. Bytes transferred = 6684911 (6600ef hex)
    
46. 
    
47. *** Loaded 6684911 (0x6600ef) bytes at 0x80010000 ***
    
48. 
    
49. 
    
50. Verifying image from 0x80010000 to 0x806700ee, size 0x6600ef ... ## Checking hash(es) for FIT Image at 80010000 ...
    
51.    Hash(es) for Image 0 (kernel@1): crc32+ sha1+
    
52.    Hash(es) for Image 1 (fdt@1): crc32+ sha1+
    
53. OK
    
54. Erasing from 0x200000 to 0x87ffff, size 0x680000 ... OK
    
55. Writting from 0x80010000 to 0x200000, size 0x6600ef ... OK
    
56. Saving Environment to NAND... Erasing NAND...
    
57. Erasing at 0xa0000 -- 100% complete.
    
58. Writing to NAND... OK
    
59. OK
    
60. Verifying flash from 0x200000 to 0x8600ee, size 0x6600ef ... OK
    
61. Updating backup image ...
    
62. Erasing from 0x2000000 to 0x267ffff, size 0x680000 ... OK
    
63. Writting from 0x80010000 to 0x2000000, size 0x6600ef ... OK
    
64. Verifying flash from 0x2000000 to 0x26600ee, size 0x6600ef ... OK
    
65. 
    
66. *** reset rootfs_data partition data! ***
    
67. 
    
68. *** Firmware upgrade completed! ***
    
69. 
    
70. Hit any key to stop firmware bootup:  2
    
71. =>   

复制代码

开机无限重启，输出如下

1. U-Boot SPL 2018.09.04-g5c61a11 (Dec 16 2022 - 13:20:39 +0800)
   
2. Trying to boot from NAND
   
3. 
   
4. 
   
5. U-Boot 2018.09.04-g5c61a11 (Dec 16 2022 - 13:20:39 +0800)
   
6. 
   
7. CPU:   MediaTek MT7621AT ver 1, eco 3
   
8. Clocks: CPU: 880MHz, DDR: 1200MHz, Bus: 220MHz, XTAL: 40MHz
   
9. Model: MediaTek MT7621 reference board (NAND)
   
10. DRAM:  256 MiB
    
11. NAND:  128 MiB
    
12. Loading Environment from NAND... OK
    
13. In:    uartlite0@1e000c00
    
14. Out:   uartlite0@1e000c00
    
15. Err:   uartlite0@1e000c00
    
16. Net:   
    
17. Warning: eth@1e100000 (eth0) using random MAC address - 8e:4f:1f:60:f9:06
    
18. eth0: eth@1e100000
    
19. ### bootdelay_process use default bootcmd="mtkboardboot"
    
20. GPIO: get pin 4 value:1
    
21. Hit any key to stop autoboot:  0
    
22. 
    
23. Starting dual image checking ...
    
24. 
    
25. Verifying main image at 0x200000 ...
    
26. ## Checking hash(es) for FIT Image at 80020000 ...
    
27.    Hash(es) for Image 0 (kernel@1): crc32+ sha1+
    
28.    Hash(es) for Image 1 (fdt@1): crc32+ sha1+
    
29. 
    
30. Passed
    
31. 
    
32. Loading from nand0, offset 0x200000
    
33. Fit image detected...
    
34.    FIT description: #JikeAP_AX1800H <AX1800H>
    
35.     Image 0 (kernel@1)
    
36.      Description:  MIPS GECOOS Linux-4.4.198
    
37.      Type:         Kernel Image
    
38.      Compression:  lzma compressed
    
39.      Data Start:   0x800100d8
    
40.      Data Size:    2917839 Bytes = 2.8 MiB
    
41.      Architecture: MIPS
    
42.      OS:           Linux
    
43.      Load Address: 0x81001000
    
44.      Entry Point:  0x81001000
    
45.      Hash algo:    crc32
    
46.      Hash value:   7eea3216
    
47.      Hash algo:    sha1
    
48.      Hash value:   320648f8d62168b7533bdb7a8469bbb9ea24a4a7
    
49.     Image 1 (fdt@1)
    
50.      Description:  MIPS GECOOS ax1800h device tree blob
    
51.      Type:         Flat Device Tree
    
52.      Compression:  uncompressed
    
53.      Data Start:   0x802d87e0
    
54.      Data Size:    10516 Bytes = 10.3 KiB
    
55.      Architecture: MIPS
    
56.      Hash algo:    crc32
    
57.      Hash value:   61eb9064
    
58.      Hash algo:    sha1
    
59.      Hash value:   610ce037135f60cf9ba76dd226cf58016276c7da
    
60.     Default Configuration: 'config@1'
    
61.     Configuration 0 (config@1)
    
62.      Description:  GECOOS
    
63.      Kernel:       kernel@1
    
64.      FDT:          fdt@1
    
65. Automatic boot of image at addr 0x80010000 ...
    
66. ## Loading kernel from FIT Image at 80010000 ...
    
67.    Using 'config@1' configuration
    
68.    Trying 'kernel@1' kernel subimage
    
69.      Description:  MIPS GECOOS Linux-4.4.198
    
70.      Type:         Kernel Image
    
71.      Compression:  lzma compressed
    
72.      Data Start:   0x800100d8
    
73.      Data Size:    2917839 Bytes = 2.8 MiB
    
74.      Architecture: MIPS
    
75.      OS:           Linux
    
76.      Load Address: 0x81001000
    
77.      Entry Point:  0x81001000
    
78.      Hash algo:    crc32
    
79.      Hash value:   7eea3216
    
80.      Hash algo:    sha1
    
81.      Hash value:   320648f8d62168b7533bdb7a8469bbb9ea24a4a7
    
82.    Verifying Hash Integrity ... crc32+ sha1+ OK
    
83. ## Loading fdt from FIT Image at 80010000 ...
    
84.    Using 'config@1' configuration
    
85.    Trying 'fdt@1' fdt subimage
    
86.      Description:  MIPS GECOOS ax1800h device tree blob
    
87.      Type:         Flat Device Tree
    
88.      Compression:  uncompressed
    
89.      Data Start:   0x802d87e0
    
90.      Data Size:    10516 Bytes = 10.3 KiB
    
91.      Architecture: MIPS
    
92.      Hash algo:    crc32
    
93.      Hash value:   61eb9064
    
94.      Hash algo:    sha1
    
95.      Hash value:   610ce037135f60cf9ba76dd226cf58016276c7da
    
96.    Verifying Hash Integrity ... crc32+ sha1+ OK
    
97.    Booting using the fdt blob at 0x802d87e0
    
98.    Uncompressing Kernel Image ... OK
    
99.    Loading Device Tree to 8fe47000, end 8fe4c913 ... OK
    
100. [    0.000000] Linux version 4.4.198 (axinchan@cnrouter.com) (GECOOS Wireless AP based on MEDIATEK SDK) 2023-07-24 06:07:34
     
101. [    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
     
102. [    0.000000] bootconsole [early0] enabled
     
103. [    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
     
104. [    0.000000] MIPS: machine is MediaTek MT7621 AX1800H (802.11ax,NAND)
     
105. [    0.000000] Determined physical RAM map:
     
106. [    0.000000]  memory: 10000000 [url=home.php?mod=space&uid=162986]@[/url] 00000000 (usable)
     
107. [    0.000000] Zone ranges:
     
108. [    0.000000]   DMA      [mem 0x0000000000000000-0x0000000000ffffff]
     
109. [    0.000000]   Normal   [mem 0x0000000001000000-0x000000000fffffff]
     
110. [    0.000000] Movable zone start for each node
     
111. [    0.000000] Early memory node ranges
     
112. [    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
     
113. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
     
114. [    0.000000] VPE topology {2,2} total 4
     
115. [    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
     
116. [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
     
117. [    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
     
118. [    0.000000] PERCPU: Embedded 10 pages/cpu @81d29000 s8544 r8192 d24224 u40960
     
119. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
     
120. [    0.000000] Kernel command line: console=ttyS0,115200 firmware=0 ubootver=2018.09.04-g5c61a11 rootfstype=squashfs,jffs2
     
121. [    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
     
122. [    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
     
123. [    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
     
124. [    0.000000] Writing ErrCtl register=00043a40
     
125. [    0.000000] Readback ErrCtl register=00043a40
     
126. [    0.000000] Memory: 248292K/262144K available (5909K kernel code, 4031K rwdata, 636K rodata, 228K init, 540K bss, 13852K reserved, 0K cma-reserved)
     
127. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
     
128. [    0.000000] Hierarchical RCU implementation.
     
129. [    0.000000] NR_IRQS:256
     
130. [    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
     
131. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
     
132. [    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
     
133. [    0.007775] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
     
134. [    0.070398] pid_max: default: 32768 minimum: 301
     
135. [    0.075115] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
     
136. [    0.081641] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
     
137. [    4.174808] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
     
138. [    4.174818] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
     
139. [    4.174828] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
     
140. [    4.174973] CPU1 revision is: 0001992f (MIPS 1004Kc)
     
141. [    0.177561] Synchronize counters for CPU 1: done.
     
142. [    3.948342] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
     
143. [    3.948350] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
     
144. [    3.948355] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
     
145. [    3.948425] CPU2 revision is: 0001992f (MIPS 1004Kc)
     
146. [    0.267910] Synchronize counters for CPU 2: done.
     
147. [    4.038429] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
     
148. [    4.038435] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
     
149. [    4.038441] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
     
150. [    4.038519] CPU3 revision is: 0001992f (MIPS 1004Kc)
     
151. [    0.353078] Synchronize counters for CPU 3: done.
     
152. [    0.357815] Brought up 4 CPUs
     
153. [    0.365090] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
     
154. [    0.374864] futex hash table entries: 1024 (order: 3, 32768 bytes)
     
155. [    0.381075] pinctrl core: initialized pinctrl subsystem
     
156. [    0.387475] NET: Registered protocol family 16
     
157. [    0.399528] mt7621_gpio 1e000600.gpio: registering 32 gpios
     
158. [    0.405121] mt7621_gpio 1e000600.gpio: registering 32 gpios
     
159. [    0.410745] mt7621_gpio 1e000600.gpio: registering 32 gpios
     
160. [    0.416752] mt7621-pci 1e140000.pcie: Got GPIO 19 for PCIe0
     
161. [    0.522498] mt7621-pci 1e140000.pcie: Failed to get gpio for PCIe1
     
162. [    0.528601] mt7621-pci 1e140000.pcie: Failed to get gpio for PCIe2
     
163. [    1.736057] PCIe port 2 link down
     
164. [    1.739288] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
     
165. [    1.753845] PCI host bridge to bus 0000:00
     
166. [    1.757884] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
     
167. [    1.764718] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
     
168. [    1.771522] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
     
169. [    1.778278] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
     
170. [    1.786892] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
     
171. [    1.794814] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
     
172. [    1.804077] pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref]
     
173. [    1.811225] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x603fffff pref]
     
174. [    1.818359] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
     
175. [    1.825124] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
     
176. [    1.831855] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref]
     
177. [    1.839567] pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref]
     
178. [    1.847233] pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref]
     
179. [    1.854941] pci 0000:00:00.0: PCI bridge to [bus 01]
     
180. [    1.859841] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x601fffff pref]
     
181. [    1.867039] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit pref]
     
182. [    1.874717] pci 0000:02:00.0: BAR 2: assigned [mem 0x60300000-0x60303fff 64bit pref]
     
183. [    1.882420] pci 0000:02:00.0: BAR 4: assigned [mem 0x60304000-0x60304fff 64bit pref]
     
184. [    1.890091] pci 0000:00:01.0: PCI bridge to [bus 02]
     
185. [    1.895017] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x603fffff pref]
     
186. [    1.903674] clocksource: Switched to clocksource GIC
     
187. [    1.910503] NET: Registered protocol family 2
     
188. [    1.915512] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
     
189. [    1.922395] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
     
190. [    1.928824] TCP: Hash tables configured (established 2048 bind 2048)
     
191. [    1.935172] UDP hash table entries: 256 (order: 1, 8192 bytes)
     
192. [    1.940921] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
     
193. [    1.947431] NET: Registered protocol family 1
     
194. [    1.965294] squashfs: version 4.0 (2009/01/31) Phillip Lougher
     
195. [    1.971035] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
     
196. [    1.983512] io scheduler noop registered
     
197. [    1.987399] io scheduler deadline registered (default)
     
198. [    1.994114] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
     
199. [    2.001415] console [ttyS0] disabled
     
200. [    2.004973] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 33, base_baud = 3125000) is a 16550A
     
201. [    2.013946] console [ttyS0] enabled
     
202. [    2.013946] console [ttyS0] enabled
     
203. [    2.020845] bootconsole [early0] disabled
     
204. [    2.020845] bootconsole [early0] disabled
     
205. [    2.029298] 1e000d00.uartfull: ttyS1 at MMIO 0x1e000d00 (irq = 34, base_baud = 3125000) is a 16550A
     
206. [    2.040558] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
     
207. [    2.047145] nand: AMD/Spansion S34ML01G2
     
208. [    2.051067] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
     
209. [    2.059229] Scanning device for bad blocks
     
210. [    2.967186] 4 ofpart partitions found on MTD device mtk-nand
     
211. [    2.972849] Creating 4 MTD partitions on "mtk-nand":
     
212. [    2.977832] 0x000000000000-0x000000080000 : "Bootloader"
     
213. [    2.984656] 0x000000080000-0x000000100000 : "Config"
     
214. [    2.990848] 0x000000100000-0x000000180000 : "Factory"
     
215. [    2.997229] 0x000000180000-0x000007fe0000 : "firmware"
     
216. [    3.454628] len should not be over partition end
     
217. [    3.459258] no rootfs found after FIT image in "firmware"
     
218. [    4.797921] libphy: Fixed MDIO Bus: probed
     
219. [    4.863878] libphy: mdio: probed
     
220. [    4.868070] mac MAC (Factory)(0X03FFF4) A4:39:B6:40:40:08
     
221. [    4.874034] mtk_soc_eth 1e100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
     
222. [    4.885218] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 10
     
223. [    4.931559] MT7915 DBDC Enabled, VERSION: 20221209
     
224. [    4.936401] LITTLE_ENDIAN
     
225. [    4.939019] Use the default iPAiLNA bin image!
     
226. [    4.944300] MT7915 [ra0] type:256 num:0 pre:ra0
     
227. [    4.960661] mt7621_wdt 1e000100.wdt: Initialized
     
228. [    4.966808] NET: Registered protocol family 10
     
229. [    4.972624] NET: Registered protocol family 17
     
230. [    4.977192] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
     
231. [    4.989814] 8021q: 802.1Q VLAN Support v1.8
     
232. [    5.033761] mt753x gsw: Switch is MediaTek MT7530 rev 1
     
233. [    5.060482] libphy: mt753x_mdio: probed
     
234. [    5.070379] hctosys: unable to open rtc device (rtc0)
     
235. [    5.076503] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
     
236. [    5.084010] Please append a correct "root=" boot option; here are the available partitions:
     
237. [    5.092370] 1f00             512 mtdblock0  (driver?)
     
238. [    5.097441] 1f01             512 mtdblock1  (driver?)
     
239. [    5.102493] 1f02             512 mtdblock2  (driver?)
     
240. [    5.107559] 1f03          129408 mtdblock3  (driver?)
     
241. [    5.112611] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
     
242. [    5.120890] Rebooting in 1 seconds..

复制代码

2023.12.21 更新
刷入另一个贴子的 u-boot 后，再次刷入 集客AX1800H 固件
成功启动


jcg q20 路由刷了集客246nd 固件速率 速度慢 5g只能跑150M


刷入 u-boot 记录

1. => mtkautoboot
   
2. 
   
3.   *** U-Boot Boot Menu ***
   
4. 
   
5.      1. Startup system (Default)
   
6.      2. Upgrade firmware
   
7.      3. Upgrade bootloader
   
8.      4. Upgrade bootloader (advanced mode)
   
9.      5. Load image
   
10.      0. U-Boot console
    
11. 
    
12. 
    
13.   Press UP/DOWN to move, ENTER to select
    
14. 
    
15. *** Upgrading Bootloader ***
    
16. 
    
17. Available load methods:
    
18.     0 - TFTP client (Default)
    
19.     1 - Xmodem
    
20.     2 - Ymodem
    
21.     3 - Kermit
    
22.     4 - S-Record
    
23. 
    
24. Select (enter for default):
    
25. 
    
26. Input U-Boot's IP address: 192.168.168.14
    
27. Input TFTP server's IP address: 192.168.168.4
    
28. Input IP netmask: 255.255.255.0
    
29. Input file name: mtk-uboot.bin
    
30. 
    
31. Using eth@1e100000 device
    
32. TFTP from server 192.168.168.4; our IP address is 192.168.168.14
    
33. Filename 'mtk-uboot.bin'.
    
34. Load address: 0x80010000
    
35. Loading: ####################################
    
36.          50.8 KiB/s
    
37. done
    
38. Bytes transferred = 524288 (80000 hex)
    
39. 
    
40. *** Loaded 524288 (0x80000) bytes at 0x80010000 ***
    
41. 
    
42. 
    
43. Erasing from 0x20000 to 0x7ffff, size 0x60000 ... OK
    
44. Writting from 0x80030000 to 0x20000, size 0x60000 ... OK
    
45. Verifying from 0x20000 to 0x7ffff, size 0x60000 ... OK
    
46. 
    
47. *** Bootloader upgrade completed! ***

复制代码

jzho***

参考这个 看看， 我觉得是要刷BREED，原厂的mtkboot不兼容集客

JCG Q20无法刷集客
https://www.right.com.cn/forum/thread-8275202-1-1.html
(出处: 恩山无线论坛)


不过刷breed（就是UBOOT），风险很高，没有编程器尽量不要尝试

fej***

jzhou404 发表于 2023-12-21 09:36
参考这个 看看， 我觉得是要刷BREED，原厂的mtkboot不兼容集客

JCG Q20无法刷集客

感谢大佬答疑

没有用过编程器，TTL 也是最近才知道怎么使用

后续我看看
[沛喆PZ-L5可以刷集客AX1800H] 原贴楼主后续有没什么其他说明

最后没辙情况下，再试刷 breed

fej***

jzhou404 发表于 2023-12-21 09:36
参考这个 看看， 我觉得是要刷BREED，原厂的mtkboot不兼容集客

JCG Q20无法刷集客

最后刷了 uboot 解决了