找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 505|回复: 7

jcg q20 ttf刷机 一直卡在这界面

[复制链接]
Automatic boot of image at addr 0x80010000 ...
## Booting kernel from Legacy Image at 80010000 ...
   Image Name:          JCG-Q20-pb-boot
   Image Type:   MIPS Linux Kernel Image (uncompressed)
   Data Size:    18685841 Bytes = 17.8 MiB
   Load Address: 80001000
   Entry Point:  805ec1f0
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

INUX started...
Linux version 3.4.113 (root@hiboy-VirtualBox) (gcc version 4.4.7 (GCC) ) #1 SMP                                                                                                                                                              Thu Oct 12 04:24:31 CST 2023

MediaTek SoC: MT7621A, RevID: 0103, RAM: DDR3, XTAL: 40MHz
CPU/OCP/SYS frequency: 880/293/220 MHz
CONFIG_RALINK_RAM_SIZE:256MB
prom get memory:256MB
CPU revision is: 0001992f (MIPS 1004Kc)
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00010000
Movable zone start PFN for each node
Early memory PFN ranges
    0: 0x00000000 -> 0x00010000
Detected 3 available secondary CPU(s)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
PERCPU: Embedded 7 pages/cpu @81203000 s5984 r8192 d14496 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock5 rootfstype=squas                                                                                                                                                             hfs
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Writing ErrCtl register=0007fb0c
Readback ErrCtl register=0007fb0c
Memory: 248296k/262144k available (6098k kernel code, 13848k reserved, 4980k dat                                                                                                                                                             a, 244k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:72
MIPS GIC RevID: 3.0
Setting up vectored interrupts
console [ttyS0] enabled
Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 1: done.
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 2: done.
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 3: done.
Brought up 4 CPUs
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref]
pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x603fffff pref]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref]
pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [mem 0x60000000-0x601fffff pref]
pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit pref]
pci 0000:02:00.0: BAR 2: assigned [mem 0x60300000-0x60303fff 64bit pref]
pci 0000:02:00.0: BAR 4: assigned [mem 0x60304000-0x60304fff 64bit pref]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0:   bridge window [mem 0x60200000-0x603fffff pref]
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay (lpj = 1167360)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 484
io scheduler noop registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000c00 (irq = 34) is a 16550A
Ralink GPIO driver initialized. Number of GPIO: 64, GPIO mode: 000A05AC
loop: module loaded
MediaTek NAND driver init, version v2.1
MTK NFI: NAND ID [98 F1, 80 15 F2 16]
MTK NFI: NAND chip with device ID 98f1 is not found in MTK table!
MTK NFI: try detect NAND chip from bootstrap mode (01)
NAND device: Manufacturer ID: 0x98, Chip ID: 0xf1 (Toshiba NAND 128MiB 3,3V 8-bi                                                                                                                                                             t), 128MiB, page size: 2048, OOB size: 64
Scanning device for bad blocks
Bad eraseblock 768 at 0x000006000000
Creating 11 MTD partitions on "MT7621-NAND":
0x000000000000-0x000000080000 : "Bootloader"
0x000000080000-0x000000100000 : "CFG_Bdata"
0x000000100000-0x000000180000 : "Factory"
0x000000180000-0x000000200000 : "Reserved"
0x000000200000-0x000010200326 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "MT7621-NAND" -- size t                                                                                                                                                             runcated to 0x7d80000
0x000007f80000-0xfffffffff977fcda : "RootFS"
mtd: partition "RootFS" is out of reach -- disabled
0x000000000000-0x000000080000 : "Config"
0x000000080000-0x000000480000 : "Storage"
0x000000480000-0x000006580000 : "RWFS"
0x000000200000-0x000001a00000 : "Firmware_Stub"
0x000000000000-0x000007f80000 : "ALL"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Ralink APSoC Ethernet Driver v3.2.4 (raeth)
raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536
raeth: NAPI & GRO support, weight 64
raeth: Byte Queue Limits (BQL) support
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
p p t p driver version 0.8.5
register mt_drv
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
<--mt7916_hif_init()
Rx[0] Ring: total 24576 bytes allocated
Rx[1] Ring: total 16384 bytes allocated
<-- pci_alloc_tx_rx_ring_mem, Status=0
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)


=== pAd = c0301000, size = 11497216 ===

<-- RTMPAllocAdapterBlock, Status=0
PCI CSRBaseAddress =0xc0200000, csr_addr=0xc0200000!
RTMPInitPCIeDevice():device_id=0x7915
mt7915_init()-->
Use the default iPAiLNA bin image!
<--mt7915_init()
RtmpOSFileOpen(): Error 2 opening /etc_ro/Wireless/l1profile.dat
Rx[0] Ring: total 24576 bytes allocated
Rx[1] Ring: total 24576 bytes allocated
Rx[2] Ring: total 8192 bytes allocated
Rx[3] Ring: total 16384 bytes allocated
Rx[4] Ring: total 8192 bytes allocated
<-- pci_alloc_tx_rx_ring_mem, Status=0
nf_conntrack version 0.5.0 (32768 buckets, 32768 max)
xt_time: kernel timezone is -0000
Bridge firewalling registered
gre: GRE over IPv4 demultiplexor driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
ASUS NVRAM, v0.08. Available space: 131072. Integrity: Signature FAILED!
end_request: I/O error, dev mtdblock5, sector 0
SQUASHFS error: squashfs_read_data failed to read block 0x0
SQUASHFS error: unable to read squashfs_super_block
VFS: Cannot open root device "mtdblock5" or unknown-block(31,5): error -5
Please append a correct "root=" boot option; here are the available partitions:
1f00             512 mtdblock0  (driver?)
1f01             512 mtdblock1  (driver?)
1f02             512 mtdblock2  (driver?)
1f03             512 mtdblock3  (driver?)
1f04          128512 mtdblock4  (driver?)
1f06             512 mtdblock6  (driver?)
1f07            4096 mtdblock7  (driver?)
1f08           99328 mtdblock8  (driver?)
1f09           24576 mtdblock9  (driver?)
1f0a          130560 mtdblock10  (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
我的恩山、我的无线 The best wifi forum is right here.
恭喜你这一刷原机数据全毁包括eeprom
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

来自手机 | 显示全部楼层
刷机前没有先备份吗?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
paldier 发表于 2023-12-29 15:12
恭喜你这一刷原机数据全毁包括eeprom

大不了买过一个,这个就当练手了
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
骑猪追宝马 发表于 2023-12-29 15:31
刷机前没有先备份吗?

没有备份,还能救么?

点评

看看好像有q20救砖的帖子,你找找看  详情 回复 发表于 2023-12-29 15:36
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

来自手机 | 显示全部楼层
唐尼蛮蛮 发表于 2023-12-29 15:33
没有备份,还能救么?

看看好像有q20救砖的帖子,你找找看
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
骑猪追宝马 发表于 2023-12-29 15:36
看看好像有q20救砖的帖子,你找找看

就是根据救砖步骤来的。结果一直在这一步
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
paldier 发表于 2023-12-29 15:12
恭喜你这一刷原机数据全毁包括eeprom

这种还能进u-boot 么?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-29 09:07

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表