帮忙看下刷LEAN 固件出现这个启动问题怎么解决

sqy***

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e1
B -       201 - PBL, Start
B -      2736 - bootable_media_detect_entry, Start
B -      2882 - bootable_media_detect_success, Start
B -      2886 - elf_loader_entry, Start
B -     11376 - auth_hash_seg_entry, Start
B -     11619 - auth_hash_seg_exit, Start
B -    250133 - elf_segs_hash_verify_entry, Start
B -    310651 - PBL, End
B -    471194 - SBL1, Start
B -    547017 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    556442 - pm_device_init, Start
B -    731542 - PM_SET_VAL:Skip
D -    172996 - pm_device_init, Delta
B -    733769 - pm_driver_init, Start
D -      5307 - pm_driver_init, Delta
B -    740265 - clock_init, Start
D -      2135 - clock_init, Delta
B -    744322 - boot_flash_init, Start
D -      3355 - boot_flash_init, Delta
B -    751367 - boot_config_data_table_init, Start
D -      1067 - boot_config_data_table_init, Delta - (575 Bytes)
B -    761829 - Boot Setting :  0x00000618
B -    765580 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:10
B -    772595 - sbl1_ddr_set_params, Start
B -    776347 - CPR configuration: 0x30c
B -    779824 - cpr_init, Start
B -    782599 - Rail:0 Mode: 5 Voltage: 800000
B -    787845 - CL CPR settled at 752000mV
B -    790560 - Rail:1 Mode: 5 Voltage: 880000
B -    794830 - Rail:1 Mode: 7 Voltage: 888000
D -     16561 - cpr_init, Delta
B -    801631 - Pre_DDR_clock_init, Start
B -    805749 - Pre_DDR_clock_init, End
B -    809043 - DDR Type : PCDDR4
B -    815783 - do ddr sanity test, Start
D -      1037 - do ddr sanity test, Delta
B -    819596 - DDR: Start of HAL DDR Boot Training
B -    824232 - DDR: End of HAL DDR Boot Training
B -    829996 - DDR: Checksum to be stored on flash is -1813671348
B -    840397 - Image Load, Start
D -    334829 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -   1175317 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -   1182973 - Image Load, Start
D -      9760 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -   1192824 - Image Load, Start
D -     30897 - RPM Image Loaded, Delta - (105964 Bytes)
B -   1223812 - Image Load, Start
D -    132553 - APPSBL Image Loaded, Delta - (539886 Bytes)
B -   1356518 - QSEE Execution, Start
D -        91 - QSEE Execution, Delta
B -   1362313 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -   1368718 - SBL1, End
D -    899811 - SBL1, Delta
S - Flash Throughput, 4430 KB/s  (2046365 Bytes,  461917 us)
S - DDR Frequency, 600 MHz
S - Core 0 Frequency, 800 MHz


U-Boot 2016.01 (Sep 24 2022 - 19:03:25 +0800)

DRAM:  smem ram ptable found: ver: 1 len: 4
1 GiB
NAND:  Could not find nand_gpio in dts, using defaults
ONFI device found
ID = 1580a1c2
Vendor = c2
Device = a1
SPI_ADDR_LEN=3
SF: Detected MX25U3235F with page size 256 Bytes, erase size 64 KiB, total 4 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x400000
132 MiB
MMC:   sdhci: Node Not found, skipping initialization

PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
machid: 801000a
MMC Device 0 not found
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid

Net:   MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd101
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
Hit any key to stop autoboot:  0
Booting from partition: 2
ubi0: attaching mtd2
ubi0: scanning is finished
UBI init error 22
Saving Environment to SPI Flash...
Erasing SPI flash...Writing to SPI flash...done
changed to active 1
resetting ...

无限制重起