有人了解运营商光猫的启动流程吗？

bk3677

我有一个退役的联通光猫（HG2543C1）烽火科技产的，这个光猫有wifi功能所以想刷个固件做个中继路由。本以为可以直接上电启动光猫连接无线操作，但是启动后只有电源灯在亮并且每隔大概15s或20s就闪烁一次，wps、wifi、reset键按了也没有反应。
本来都打算放弃了却无意间发现这个猫还给了ttl接口，看了滚码后的输出发现这个猫一直在重复做CFE的引导，并且看输出也没有报什么明显的error。然后就想从CFE入手看看能不能有操作的空间，结果发现这个CFE被严重阉割了，几乎没有什么可以配置的命令：

1. CFE> help
   
2. Available commands:
   
3. 
   
4. x                  Change extra partitions size
   
5. comp           Find NAND bad blocks
   
6. fb                 Find NAND bad blocks
   
7. dn                Dump NAND contents along with spare area
   
8. phy              Set memory or registers.
   
9. sm               Set memory or registers.
   
10. dm               Dump memory or registers.
    
11. db                Dump bytes.
    
12. dh                Dump half-words.
    
13. dw               Dump words.
    
14. w                 Write the whole image start from beginning of the flash
    
15. e                  Erase NAND flash
    
16. ws                Write whole image (priviously loaded by kermit or JTAG) to flash .
    
17. go                goto and execute from specefic address.
    
18. enable_timeout                 enable console timeout.
    
19. disable_timeout                disable console timeout.
    
20. r                   Run program from flash image or from host depend on [f/h] flag
    
21. p                  Print boot line and board parameter info
    
22. c                  Change booline parameters
    
23. i                   Erase persistent storage data
    
24. ddr               Change board DDR config
    
25. a                  Change board AFE ID
    
26. b                  Change board parameters
    
27. reset                  Reset the board
    
28. pmdio                Pseudo MDIO access for external switches.
    
29. spi                     Legacy SPI access of external switch.
    
30. force                 override chipid check for images.
    
31. dumpnvram            Dump NVRAM
    
32. ledtest               FH led test
    
33. flashtest            FH flash test
    
34. memtest           FH memory test
    
35. upg                   access multicast upgrade
    
36. help                  Obtain help for CFE commands
    
37. 
    
38. For more information about a command, enter 'help command-name'
    
39. *** command status = 0

复制代码

上面所有的命令我都试了个遍，虽然可以修猫的参数、导出寄存器里的内容、甚至往里传固件，但是这种操作实在有些超出我的能力范围了，全都是16进制，并且dump和write的运行效率十分低下，所有数据都只能依靠ttl那三根线进行传输。插了网线也没有办法建立起有效连接，手动设置了固定 ip地址后 pc端就一直显示正在连接。
当时我就以为光猫的固件可能没有存在猫里，有可能要靠光纤从运营商那边拉下来，所以就试着把目前办理的移动宽带的光纤插上去了。结果确实CFE的引导继续进行下去了，不过感觉也报了不少的error。所以还是想向各位请教下，这个固件是需要接入运营商的光纤下载到猫里的？还是说本来就是存在猫里的，只不过需要一些验证才能继续引导固件启动？最后有谁了解这个光猫启动的流程啊？这玩意启动时都做了哪些验证啊？

邪恶海盗

"不停重复CFE引导"说明固件挂了,跟光纤没屁关系...

bk3677

邪恶海盗 发表于 2024-3-6 17:47
"不停重复CFE引导"说明固件挂了,跟光纤没屁关系...

我最开也是这么认为的，但按道理来说固件不应该自己会挂掉呀？难道办理宽带手续的时候联通直接就把猫里的固件删除了？

邪恶海盗

bk3677 发表于 2024-3-6 17:59
我最开也是这么认为的，但按道理来说固件不应该自己会挂掉呀？难道办理宽带手续的时候联通直接就把猫里的 ...

为什么不会,这世界上有什么是那么绝对的么?

idiu

烽火禁不住折腾。我换地区就把固件折腾坏了

bk3677

邪恶海盗 发表于 2024-3-6 18:09
为什么不会,这世界上有什么是那么绝对的么?

但有一点，我接上光纤后再启动时，所有按键就都有效果了，并且Wi-Fi模块也能启动，不过没有dhcp，192也进不去。所以就很好奇固件到底是不是从光纤上拉下来的。

bk3677

idiu 发表于 2024-3-6 18:35
烽火禁不住折腾。我换地区就把固件折腾坏了

我其实就是看上他有个Wi-Fi模块了，所以想看看能不能起死回生一下…

邪恶海盗

bk3677 发表于 2024-3-6 19:50
但有一点，我接上光纤后再启动时，所有按键就都有效果了，并且Wi-Fi模块也能启动，不过没有dhcp，192也进 ...

有证据能证明你这个结论么?

bk3677

邪恶海盗 发表于 2024-3-6 20:04
有证据能证明你这个结论么?

这个不能说是结论，只是我的一个想法。因为有无光纤的接入在光猫启动后确实产生了不同的引导现象，这也是为什么我很想找一个业内的帮我解惑。这两个引导我都记录了log。
第一个是没插入光纤的log，重复cfe引导：

1. HELO
   
2. CPUI
   
3. L1CI
   
4. HELO
   
5. CPUI
   
6. L1CI
   
7. 4.1604_CT2015_Yueme-1.0.38-116.233
   
8. AVSD
   
9. DRAM
   
10. ***** DDR INITIALIZATION START ******
    
11. NVRAM memcfg 0x322
    
12. mcb configuration = 6
    
13. MemsysInit lpf0wb_r4p0 1.2.0.4 20150422
    
14. DDR3
    
15. 930A4660 B0014000 B0016000 00000000 00000000 004031D9
    
16. MCB rev=0x00030301 Ref ID=0x031D9 Sub Bld=0x004
    
17. Dram Timing 07-07-07
    
18. start of memsys_begin
    
19. mc_cfg_init(): Initialize the default values on mc_cfg
    
20. init_memc_dram_profile(): Initializing MEMC DRAM profile
    
21. Poll PHY Status register
    
22. PHY Status= 1
    
23. Disable Auto-Refresh
    
24. [0xb001420c] = 0x00017b00
    
25. [0xb0014200] = 0x00000305
    
26. End of memsys_begin
    
27. Add/Ctl Alignment
    
28. no adjustment
    
29. ZQ Cal LP PHY
    
30. p_term=0x03 n_term=0x03 p_drive=0x11 n_drive=0x10
    
31. R in Ohm
    
32. P: Finger=0x2D0 Term=0xF0 Drv=0x3C
    
33. N: Finger=0x2D0 Term=0xF0 Drv=0x3C
    
34. PLL Ref(Hz)=0x02FAF080 UI STEPS=0x056
    
35. DDR CLK(MHz)=0x215 WL CLK dly(ps)=0x0C8 bitT(ps)=0x3AA VDLsize(fs)=0x2A9A CLK_VDL=0x01A
    
36. start of memc_init
    
37. [0xb0014004] = 0x01100044
    
38. [0xb0014004] = 0x01100244
    
39. [0xb0014004] = 0x01100644
    
40. [0xb0014234] = 0x00000501
    
41. Enable Auto-Refresh
    
42. [0xb001420c] = 0x00007b00
    
43. [0xb0014110] = 0x11100f0e
    
44. [0xb0014114] = 0x15141312
    
45. [0xb0014118] = 0x19181716
    
46. [0xb001411c] = 0x00001b1a
    
47. [0xb0014150] = 0x04000000
    
48. [0xb0014154] = 0x08070605
    
49. [0xb0014158] = 0x00000a09
    
50. [0xb0014190] = 0x000d0c0b
    
51. FUNC cfg_memc_timing_ctrl
    
52. [0xb0014214] = 0x06070707
    
53. [0xb0014218] = 0x00040006
    
54. [0xb001421c] = 0x1b00041b
    
55. [0xb0014220] = 0x00040008
    
56. [0xb0014224] = 0x0a000058
    
57. END FUNC cfg_memc_timing_ctrl
    
58. End of memc_init
    
59. start of pre_shmoo
    
60. [0xb0014004] = 0xc1100744
    
61. end of pre_shmoo
    
62. SHMOO 28nm
    
63. B0016000 B0014800 00000000 00020000 00000000
    
64. Shmoo WL
    
65. One UI Steps : 0x61
    
66. disable_dram_refresh
    
67. [0xb001420c] = 0x00017b00
    
68. enable_dram_refresh
    
69. [0xb001420c] = 0x00007b00
    
70.    0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
    
71.    0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
    
72. 00 S---------------X++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    
73. 01 S--------------X+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    
74. Shmoo RD En
    
75. B0 RISE UI=0 VDL=39 PICK UI=1 VDL=39
    
76. B1 RISE UI=0 VDL=3B PICK UI=1 VDL=3B
    
77.    0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
    
78.    0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
    
79. 00 -S-------------------------------------------------------X+++++++++++++++++++++++++++++++++++++++
    
80. 01 -S---------------------------------------------------------X+++++++++++++++++++++++++++++++++++++
    
81. Shmoo RD DQ NP
    
82. DQS :
    
83. B0 VDL=56 ok
    
84. B1 VDL=56 ok
    
85.    0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
    
86.    0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
    
87. 00 -------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---------------
    
88. 01 -----------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++----------
    
89. 02 -------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++----------------
    
90. 03 --------------++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++----------
    
91. 04 --------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---------------
    
92. 05 -------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++----------
    
93. 06 --------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---------------
    
94. 07 ----------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++-------------
    
95. 08 -------------++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++-----------
    
96. 09 ---------++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++---------------
    
97. 10 ---------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++--------
    
98. 11 --------+++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++-----------------
    
99. 12 --------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++--------
    
100. 13 --------++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++----------------
     
101. 14 ---------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++-------
     
102. 15 --------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---------------
     
103. Shmoo RD DQ P
     
104.    0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
     
105.    0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
     
106. 00 -------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-------------
     
107. 01 -----------+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++-------
     
108. 02 --------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-------------
     
109. 03 --------------++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++----------
     
110. 04 --------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---------------
     
111. 05 -------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---------
     
112. 06 -------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++--------------
     
113. 07 ----------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-----------
     
114. 08 -------------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++------
     
115. 09 ---------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++----------
     
116. 10 ---------------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++----
     
117. 11 ---------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++--------------
     
118. 12 --------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++------
     
119. 13 --------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-------------
     
120. 14 ---------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-----
     
121. 15 ---------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++------------
     
122. Shmoo RD DQ N
     
123.    0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
     
124.    0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
     
125. 00 ++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++---------------
     
126. 01 ----+++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++----------
     
127. 02 ++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++----------------
     
128. 03 ------+++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++-----------
     
129. 04 -++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++---------------
     
130. 05 ------++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++----------
     
131. 06 -++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++---------------
     
132. 07 ---++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++-------------
     
133. 08 ----++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++-----------
     
134. 09 -++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++---------------
     
135. 10 -------++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++--------
     
136. 11 +++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++-----------------
     
137. 12 -----+++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++++--------
     
138. 13 +++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++-----------------
     
139. 14 -------+++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++-------
     
140. 15 -++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++---------------
     
141. RD DQS adjustments :
     
142. BL0: Start: 0x56 Final: 0x56
     
143. BL1: Start: 0x56 Final: 0x56
     
144. Shmoo WR DQ
     
145.    0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
     
146.    0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
     
147. 00 --++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++--------------
     
148. 01 -------++++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++++--------
     
149. 02 ---+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++---------------
     
150. 03 ----------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-----------
     
151. 04 -----+++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++------------
     
152. 05 ---------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++----------
     
153. 06 ---+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++---------------
     
154. 07 ------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++-------------
     
155. 08 -----++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++-----------
     
156. 09 --+++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++---------------
     
157. 10 --------++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++--------
     
158. 11 -++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++------------------
     
159. 12 ------+++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++-----------
     
160. 13 -+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++-----------------
     
161. 14 --------+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++----------
     
162. 15 --+++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++---------------
     
163. Shmoo WR DM
     
164. WR DM
     
165.    0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
     
166.    0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
     
167. 00 --------+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++----------
     
168. 01 --++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++--------------
     
169. start of memsys_end
     
170. [0xb0014004] = 0x81100744
     
171. [0xb0014004] = 0x81100748
     
172. end of memsys_end
     
173. DDR test done successfully
     
174. ***** DDR INITIALIZATION DONE ********
     
175. PDDR
     
176. ZBSS
     
177. L12F
     
178. MAIN
     
179. FPS0
     
180. BT06
     
181. 0001
     
182. BT05
     
183. 0412
     
184. NAN3
     
185. RFS1
     
186. NAN5
     
187. Base: 4.16_04_CT2015_Yueme
     
188. CFE version 1.0.38-116.233 for BCM96848 (32bit,SP,BE)
     
189. Build Date: Mon Feb 27 03:37:04 CST 2023 (jenkins_wang@jenkins)
     
190. Copyright (C) 2000-2013 Broadcom Corporation.
     
191. Boot Strap Register:  0xbfdbc2
     
192. Chip ID: BCM68488_A1_, MIPS: 600MHz, DDR: 400MHz, Bus: 300MHz
     
193. RDP: 428MHz
     
194. Main Thread: TP0
     
195. Total Memory: 268435456 bytes (256MB)
     
196. Boot Address: 0xb8000000
     
197. NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes
     
198. NAND flash device: , id 0xadda block 128KB size 262144KB
     
199. AFTER SYN nvramData.szBoardId = 96848EG2F2V1_UX
     
200. AFTER SYN nvramData.ulVersion = 6
     
201. [WANGKAI] BpSetBoardId:96848EG2F2V1_UX
     
202. [WANGKAI] wk_b:0
     
203. WK01
     
204. WK01
     
205. WK01
     
206. Board IP address                  : 192.168.1.1:ffffff00  
     
207. Host IP address                   : 192.168.1.100  
     
208. Gateway IP address                :   
     
209. Run from flash/host/tftp (f/h/c)  : f  
     
210. Default host run file name        :   
     
211. Default host flash file name      : bcm963xx_fs_kernel  
     
212. Boot delay (0-9 seconds)          : 1  
     
213. Boot image (0=latest, 1=previous) : 0  
     
214. Default host ramdisk file name    :   
     
215. Default ramdisk store address     : p  
     
216. Board Id (0-15)                   : 96848EG2F2V1_UX  
     
217. Number of MAC Addresses (1-32)    : 10  
     
218. Base MAC Address                  : c0:36:56:ff:13:ec  
     
219. PSI Size (1-128) KBytes           : 128  
     
220. Enable Backup PSI [0|1]           : 1  
     
221. System Log Size (0-256) KBytes    : 0  
     
222. Auxillary File System Size Percent: 0  
     
223. Main Thread Number [0|1]          : 0  
     
224. MC memory allocation (MB)         : 4  
     
225. TM memory allocation (MB)         : 20  
     
226. DHD 0 memory allocation (MB)      : 0  
     
227. DHD 1 memory allocation (MB)      : 0  
     
228. DHD 2 memory allocation (MB)      : 0  
     
229. WLan Feature                      : 0x02  
     
230. Voice Board Configuration (0-1)   : LE9641_ZSI_BB  
     
231. Partition 1 Size (MB)             :   
     
232. Partition 2 Size (MB)             :   
     
233. Partition 3 Size (MB)             :   
     
234. Partition 4 Size (MB) (Data)      : 4MB  
     
235. enable IH Wan-Wan forwarding...
     
236. data_path_go Done!!
     
237. Creating CPU ring for queue number 0 with 32 packets descriptor=0x8067c56c
     
238. Done initializing Ring 0 Base=0xa2214220K End=0xa2214420K calculated entries= 32 RDD Base=0x02214220K descriptor=0x8067c56c
     
239. Open PHY 1 on MAC 0 : link state = Down
     
240. Open PHY 2 on MAC 1 : link state = Down
     
241. Open PHY 3 on MAC 2 : link state = Down
     
242. Open PHY 4 on MAC 3 : link state = Down
     
243. *** Press u key to stop auto run (1 seconds) ***
     
244. Auto run second count down: 11Timeout or packet isn't legal. Do not enter multicast upgrade
     
245. fh_upg_upgrade: auto upgrade failed.
     
246. 0
     
247. WK01
     
248. Booting from latest image (address 0xb8020000, flash offset 0x00020000) ...
     
249. Decompression LZ4 Image OK!
     
250. Entry at 0x804135f0
     
251. Starting program at 0x804135f0
     
252. Linux version 3.4.11-rt19 (jenkins_wang@jenkins) (gcc version 4.6.2 (Buildroot 2011.11) ) #1 SMP PREEMPT Mon Feb 27 04:58:47 CST 2023
     
253. 96848EG2F2V1_UX prom init
     
254. CPU revision is: 0002a081 (Broadcom BMIPS4350)
     
255. Determined physical RAM map:
     
256. memory: 01400000 @ 0ec00000 (reserved)
     
257. memory: 00400000 @ 0e800000 (reserved)
     
258. memory: 0e800000 @ 00000000 (usable)
     
259. Zone PFN ranges:
     
260.   DMA      0x00000000 -> 0x00000400
     
261.   Normal   0x00000400 -> 0x00003a00
     
262.   HighMem  empty
     
263. Movable zone start PFN for each node
     
264. Early memory PFN ranges
     
265.     0: 0x00000000 -> 0x00004000
     
266. On node 0 totalpages: 14848
     
267. free_area_init_node: node 0, pgdat 80501970, node_mem_map 81000000
     
268.   DMA zone: 2 pages used for memmap
     
269.   DMA zone: 0 pages reserved
     
270.   DMA zone: 1022 pages, LIFO batch:0
     
271.   Normal zone: 27 pages used for memmap
     
272.   Normal zone: 13797 pages, LIFO batch:3
     
273. PERCPU: Embedded 2 pages/cpu @81084000 s5120 r8192 d19456 u32768
     
274. pcpu-alloc: s5120 r8192 d19456 u32768 alloc=2*16384
     
275. pcpu-alloc: [0] 0 [0] 1
     
276. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 14819
     
277. Kernel command line: ro noinitrd  irqaffinity=0
     
278. PID hash table entries: 1024 (order: -2, 4096 bytes)
     
279. Dentry cache hash table entries: 32768 (order: 3, 131072 bytes)
     
280. Inode-cache hash table entries: 16384 (order: 2, 65536 bytes)
     
281. Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
     
282. Primary data cache 32kB, 2-way, VIPT, no aliases, linesize 16 bytes
     
283. Memory: 231040k/237568k available (4170k kernel code, 6528k reserved, 895k data, 224k init, 0k highmem)
     
284. Preemptible hierarchical RCU implementation.
     
285. NR_IRQS:256
     
286. console [ttyS0] enabled
     
287. Allocating memory for DSP module core and initialization code
     
288. Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
     
289. Calibrating delay loop... 598.01 BogoMIPS (lpj=299008)
     
290. pid_max: default: 32768 minimum: 301
     
291. Mount-cache hash table entries: 2048
     
292. --Kernel Config--
     
293.   SMP=1
     
294.   PREEMPT=1
     
295.   DEBUG_SPINLOCK=0
     
296.   DEBUG_MUTEXES=0
     
297. Broadcom Logger v0.1 Feb 27 2023 03:45:41
     
298. CPU revision is: 0002a081 (Broadcom BMIPS4350)
     
299. Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
     
300. Primary data cache 32kB, 2-way, VIPT, no aliases, linesize 16 bytes
     
301. Brought up 2 CPUs
     
302. NET: Registered protocol family 16
     
303. registering PCI controller with io_map_base unset
     
304. bcm63xx_pcie: setting resistor calibration value to 0xb
     
305. bcm63xx_pcie: applying serdes parameters
     
306. registering PCI controller with io_map_base unset
     
307. bio: create slab <bio-0> at 0
     
308. SCSI subsystem initialized
     
309. usbcore: registered new interface driver usbfs
     
310. usbcore: registered new interface driver hub
     
311. usbcore: registered new device driver usb
     
312. PCI host bridge to bus 0000:00
     
313. pci_bus 0000:00: root bus resource [mem 0x10600000-0x106fffff]
     
314. pci_bus 0000:00: root bus resource [io  0x11700000-0x1170ffff]
     
315. pci 0000:00:09.0: [14e4:6300] type 00 class 0x0c0310
     
316. pci 0000:00:09.0: reg 10: [mem 0x1000c400-0x1000c4ff]
     
317. pci 0000:00:0a.0: [14e4:6300] type 00 class 0x0c0320
     
318. pci 0000:00:0a.0: reg 10: [mem 0x1000c300-0x1000c3ff]
     
319. PCI host bridge to bus 0000:01
     
320. pci_bus 0000:01: root bus resource [mem 0xa0000000-0xbfffffff]
     
321. pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
     
322. pci 0000:01:00.0: [14e4:005b] type 01 class 0x060400
     
323. pci 0000:01:00.0: PME# supported from D0 D3hot
     
324. pci 0000:02:00.0: [14e4:a8db] type 00 class 0x028000
     
325. pci 0000:02:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
     
326. pci 0000:02:00.0: supports D1 D2
     
327. pci 0000:01:00.0: BAR 8: assigned [mem 0xa0000000-0xa00fffff]
     
328. pci 0000:02:00.0: BAR 0: assigned [mem 0xa0000000-0xa0007fff 64bit]
     
329. pci 0000:01:00.0: PCI bridge to [bus 02-02]
     
330. pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xa00fffff]
     
331. PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
     
332. bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
     
333. skbFreeTask created successfully
     
334. gbpm_do_work scheduled
     
335. BLOG v3.0 Initialized
     
336. BLOG Rule v1.0 Initialized
     
337. Broadcom IQoS v0.1 Feb 27 2023 04:40:10 initialized
     
338. Broadcom GBPM v0.1 Feb 27 2023 04:40:13 initialized
     
339. Switching to clocksource MIPS
     
340. NET: Registered protocol family 2
     
341. IP route cache hash table entries: 4096 (order: 0, 16384 bytes)
     
342. TCP established hash table entries: 8192 (order: 2, 65536 bytes)
     
343. TCP bind hash table entries: 8192 (order: 2, 65536 bytes)
     
344. TCP: Hash tables configured (established 8192 bind 8192)
     
345. TCP: reno registered
     
346. UDP hash table entries: 512 (order: 0, 16384 bytes)
     
347. UDP-Lite hash table entries: 512 (order: 0, 16384 bytes)
     
348. NET: Registered protocol family 1
     
349. PCI: CLS 16 bytes, default 16
     
350. init_bcm_tstamp: unhandled mips_hpt_freq=300000000, adjust constants in bcm_tstamp.c
     
351. bcm_tstamp initialized, (hpt_freq=300000000 2us_div=300 2ns_mult=0 2ns_shift=0)
     
352. squashfs: version 4.0 (2009/01/31) Phillip Lougher
     
353. jffs2: version 2.2. (NAND) (SUMMARY)  \A9 2001-2006 Red Hat, Inc.
     
354. fuse init (API version 7.18)
     
355. msgmni has been set to 451
     
356. io scheduler noop registered (default)
     
357. Broadcom NAND controller (BrcmNand Controller)
     
358. mtd->oobsize=0, mtd->eccOobSize=0
     
359. NAND_CS_NAND_XOR=00000000
     
360. B4: NandSelect=40000001, nandConfig=06052300, chipSelect=0
     
361. brcmnand_read_id: CS0: dev_id=adda9095
     
362. After: NandSelect=40000001, nandConfig=06052300
     
363. Block size=00020000, erase shift=17
     
364. NAND Config: Reg=06052300, Config Ext: Reg=00000042, chipSize=256 MB, blockSize=128K, erase_shift=11
     
365. busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
     
366. timing1 not adjusted: 65644458
     
367. timing2 not adjusted: 80040e56
     
368. BrcmNAND mfg ad da Hynix HY27UF082G2A 256MB on CS0
     
369. Found NAND on CS0: ACC=c3040010, cfg=06052300, cfg_ext=00000042, flashId=adda9095, tim1=65644458, tim2=80040e56
     
370. BrcmNAND version = 0x0701 256MB @00000000
     
371. brcmnand_scan: B4 nand_select = 40000001
     
372. brcmnand_scan: After nand_select = 40000001
     
373. handle_acc_control: default CORR ERR threshold  3 bits
     
374. ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
     
375. page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
     
376. Brcm NAND controller version = 7.1 NAND flash size 256MB @10000000
     
377. ECC layout=brcmnand_oob_bch4_2k
     
378. brcmnand_scan:  mtd->oobsize=64
     
379. brcmnand_scan: oobavail=35, eccsize=512, writesize=2048
     
380. brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7
     
381. -->brcmnand_default_bbt
     
382. brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr
     
383. Bad block table Bbt0 found at page 0001ffc0, version 0x01 for chip on CS0
     
384. Bad block table 1tbB found at page 0001ff80, version 0x01 for chip on CS0
     
385. brcmnand_reset_corr_threshold: default CORR ERR threshold  3 bits for CS0
     
386. brcmnandCET: Status -> Deferred
     
387. ***** Found SQUASHFS Marker at 0x004dff00
     
388. ***** Found SQUASHFS Marker at 0x0383ff00
     
389. rootfs device :/dev/mtdblock13
     
390. Creating 13 MTD partitions on "brcmnand.0":
     
391. 0x0000004e0000-0x000003380000 : "rootfs"
     
392. 0x000003840000-0x0000066e0000 : "rootfs_update"
     
393. 0x000006700000-0x000006b00000 : "data"
     
394. 0x000000000000-0x000000020000 : "nvram"
     
395. 0x000006b00000-0x00000eb00000 : "ctmdw"
     
396. 0x00000eb00000-0x00000ef00000 : "fhconf"
     
397. 0x00000ef00000-0x00000f700000 : "fhrootfs"
     
398. 0x00000f700000-0x00000fb00000 : "fhlog"
     
399. 0x00000fb00000-0x00000ff00000 : "fhbak"
     
400. 0x000000020000-0x000003380000 : "image"
     
401. 0x000003380000-0x0000066e0000 : "image_update"
     
402. 0x000000020000-0x0000004e0000 : "bootfs"
     
403. 0x000003380000-0x000003840000 : "bootfs_update"
     
404. UBI: attaching mtd0 to ubi0
     
405. UBI: physical eraseblock size:   131072 bytes (128 KiB)
     
406. UBI: logical eraseblock size:    126976 bytes
     
407. UBI: smallest flash I/O unit:    2048
     
408. UBI: VID header offset:          2048 (aligned 2048)
     
409. UBI: data offset:                4096
     
410. UBI: max. sequence number:       2
     
411. UBI: attached mtd0 to ubi0
     
412. UBI: MTD device name:            "rootfs"
     
413. UBI: MTD device size:            46 MiB
     
414. UBI: number of good PEBs:        373
     
415. UBI: number of bad PEBs:         0
     
416. UBI: number of corrupted PEBs:   0
     
417. UBI: max. allowed volumes:       128
     
418. UBI: wear-leveling threshold:    4096
     
419. UBI: number of internal volumes: 1
     
420. UBI: number of user volumes:     1
     
421. UBI: available PEBs:             0
     
422. UBI: total number of reserved PEBs: 373
     
423. UBI: number of PEBs reserved for bad PEB handling: 3
     
424. UBI: max/mean erase counter: 1/0
     
425. UBI: image sequence number:  0
     
426. UBI: background thread "ubi_bgt0d" started, PID 252
     
427. PPP generic driver version 2.4.2
     
428. PPP BSD Compression module registered
     
429. PPP Deflate Compression module registered
     
430. NET: Registered protocol family 24
     
431. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
432. PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
     
433. ehci_hcd 0000:00:0a.0: setting latency timer to 64
     
434. ehci_hcd 0000:00:0a.0: EHCI Host Controller
     
435. ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
     
436. ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
     
437. ehci_hcd 0000:00:0a.0: irq 16, io mem 0x1000c300
     
438. ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
     
439. hub 1-0:1.0: USB hub found
     
440. hub 1-0:1.0: 1 port detected
     
441. ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
     
442. PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
     
443. ohci_hcd 0000:00:09.0: setting latency timer to 64
     
444. ohci_hcd 0000:00:09.0: OHCI Host Controller
     
445. ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
     
446. ohci_hcd 0000:00:09.0: irq 18, io mem 0x1000c400
     
447. hub 2-0:1.0: USB hub found
     
448. hub 2-0:1.0: 1 port detected
     
449. usbcore: registered new interface driver usblp
     
450. i2c /dev entries driver
     
451. brcmboard: brcm_board_init entry
     
452. g_ulSdramSize is 268435456
     
453. ****************(BpGetResetToDefaultExtIntr),intr = 4
     
454. ****************(BpGetWirelessSesExtIntr),intr = 6
     
455. ****************(BpGetWifiOnOffExtIntr),intr = 5
     
456. ****************(BpGetLedIndicateExtIntr),intr = 0
     
457. Wifi Button: Button Interrupt 0x5 is enabled
     
458. SES: Button Interrupt 0x6 is enabled

复制代码

第二个是接了光纤的，跳出了重复引导：

1. <b><i>字数限制问题，前面重复的我就省略了</i></b>
   
2. 
   
3. ****************(BpGetResetToDefaultExtIntr),intr = 4
   
4. ****************(BpGetWirelessSesExtIntr),intr = 6
   
5. ****************(BpGetWifiOnOffExtIntr),intr = 5
   
6. ****************(BpGetLedIndicateExtIntr),intr = 0
   
7. Wifi Button: Button Interrupt 0x5 is enabled
   
8. SES: Button Interrupt 0x6 is enabled
   
9. DYING GASP IRQ Initialized and Enabled
   
10. LED: Button Interrupt 0x0 is enabled
    
11. led: onoff is (1)
    
12. Serial: BCM63XX driver $Revision: 3.00 $
    
13. Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)
    
14. ttyS0 at MMIO 0xb0800640 (irq = 104) is a BCM63XX
    
15. ttyS1 at MMIO 0xb0800660 (irq = 105) is a BCM63XX
    
16. BPM: tot_mem_size=268435456B (256MB), buf_mem_size <10%> =26843540B (25MB), num of buffers=10420, buf size=2576
    
17. Broadcom BPM Module Char Driver v0.1 Feb 27 2023 04:12:17 Registered<244>
    
18. xt_time: kernel timezone is -0000
    
19. TCP: cubic registered
    
20. NET: Registered protocol family 10
    
21. IPv6 over IPv4 tunneling driver
    
22. NET: Registered protocol family 17
    
23. *******initialize netlink succese!*******
    
24. Initializing MCPD Module
    
25. Ebtables v2.0 registered
    
26. ebt_time registered
    
27. ebt_ftos registered
    
28. ebt_wmm_mark registered
    
29. L2TP core: blog_l2tp_rcv_check
    
30. L2TP core driver, V2.0
    
31. PPPoL2TP kernel driver, V2.0
    
32. 8021q: 802.1Q VLAN Support v1.8
    
33. Created /proc/driver/fhdrv_kdrv_flash_cnt.
    
34. VFS: Mounted root (squashfs filesystem) readonly on device 31:13.
    
35. Freeing unused kernel memory: 224k freed
    
36. init started: BusyBox v1.17.2 (2023-02-27 08:10:36 CST)
    
37. starting pid 303, tty '': '/bin/sh -l -c "bcm_boot_launcher start"'
    
38. Mounting filesystems...
    
39. Copied 3 bytes from address 0x00000000 in flash to /var/test
    
40. Copied 3 bytes from address 0x00000000 in flash to /var/test2
    
41. cp: can't stat '/fhbak/data_temp/*': No such file or directory
    
42. cp: can't stat '/fhbak/fhconf_temp/*': No such file or directory
    
43. Begin restore wlan calibration.....
    
44. Configuring system...
    
45. Loading drivers and kernel modules...
    
46. wlcsm: module license 'Proprietary' taints kernel.
    
47. Disabling lock debugging due to kernel taint
    
48. Initializing WLCSM Module
    
49. WLCSM Module loaded successfully
    
50. optical_wan_type = 2, WAN_GPON=1, WAN_EPON=2
    
51. wantype_optical = EPON
    
52. scratchpad RdpaWanType - EPON
    
53. enable IH Wan-Wan forwarding...
    
54. data_path_go Done!!
    
55. Bridge fastpath module. compiled Feb 27 2023 , 04:31:34
    
56. brcmchipinfo: brcm_chipinfo_init entry
    
57. NBUFF v1.0 Initialized
    
58. Initialized fcache state
    
59. Broadcom Packet Flow Cache  Char Driver v2.2 Feb 27 2023 04:16:50 Registered<242>
    
60. Created Proc FS /procfs/fcache
    
61. Broadcom Packet Flow Cache registered with netdev chain
    
62. Broadcom Packet Flow Cache learning via BLOG enabled.
    
63. [FHW]  pktDbgLvl[0xc0521860]=0
    
64. [FHW]  fhw_construct:
    
65. Initialized Fcache HW accelerator layer state
    
66. Constructed Broadcom Packet Flow Cache v2.2 Feb 27 2023 04:16:50
    
67. i2c i2c-0: Failed to register i2c client gpon_i2c at 0x50 (-16)
    
68. i2c i2c-0: Failed to register i2c client gpon_i2c at 0x51 (-16)
    
69. Broadcom BCM68488_A1_ Ethernet Network Device v0.1 Feb 27 2023 04:31:56
    
70. dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
    
71. eth1: <Int sw port: 0> <Logical : 00> PHY_ID <0x01800001 : 0x01> MAC : C0:36:56:FF:13:EC
    
72. eth0: <Int sw port: 1> <Logical : 01> PHY_ID <0x01800002 : 0x02> MAC : C0:36:56:FF:13:EC
    
73. eth3: <Int sw port: 2> <Logical : 02> PHY_ID <0x00800003 : 0x03> MAC : C0:36:56:FF:13:EC
    
74. eth2: <Int sw port: 3> <Logical : 03> PHY_ID <0x00800004 : 0x04> MAC : C0:36:56:FF:13:EC
    
75. Ethernet Auto Power Down and Sleep: Enabled
    
76. All Port Bit Map: 0x000f: eth1,eth0,eth3,eth2
    
77.    Chip WAN Only Ports 0000, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0000:
    
78.    Chip WAN Preffered Ports 0000, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0000:
    
79.    Chip LAN Only Ports 0000, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0000:
    
80.    WAN/LAN Both Capable Ports 0x000f:eth1,eth0,eth3,eth2
    
81. Energy Efficient Ethernet: Enabled
    
82. Creating Enet CPU ring for queue number 1 with 512 packets,Descriptor base=aa114080
    
83. Creating Enet CPU ring for queue number 0 with 512 packets,Descriptor base=abfe0080
    
84. Broadcom Packet Flow Cache HW acceleration enabled.
    
85. Broadcom Packet Flow Cache HW acceleration enabled.
    
86. Creating CPU ring for queue number 2 with 1024 packets descriptor=0xc0638704
    
87.   wfd_bind: Dev (null) wfd_idx 2 wl_radio_idx -1 Type skb configured WFD thread wfd2-thrd minQId/maxQId (10/10), status (0) qmask 0x4
    
88. Instantiating WFD 2 thread
    
89. Wifi Forwarding Driver is initialized!
    
90. jffs2: notice: (309) check_node_data: wrong data CRC in data node at 0x070ac584: read 0xb5cbcfdd, calculated 0x2462abff.
    
91. --SMP support
    
92. --WAPI support
    
93. wl: dsl_tx_pkt_flush_len=338
    
94. wl: norm_wmark_tot=6773, pktc_wmark_tot=6773
    
95. PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
    
96. wl: passivemode=1
    
97. wl0: creating kthread wl0-kthrd
    
98. wl: napimode=0
    
99. initvars_cis_pci: Not CIS format
    
100. Neither SPROM nor OTP has valid image
     
101. wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
     
102. wl: ID=pci/2/0/
     
103. fname is /etc/bcm43217_96848EG2F2V1_UX_map_min.bin
     
104. wl: ID=pci/2/0/
     
105. fname is /etc/bcm43217_map_min.bin
     
106. wl: loading /etc/bcm43217_map_min.bin
     
107. wl: updating srom from flash...
     
108. wl: updating srom from flash...
     
109. srom rev:8
     
110. wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=48
     
111. wl0: allocskbmode=1 currallocskbsz=1024
     
112. Creating CPU ring for queue number 0 with 1024 packets descriptor=0xc06386cc
     
113.   wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type skb configured WFD thread wfd0-thrd minQId/maxQId (8/8), status (0) qmask 0x1
     
114. Instantiating WFD 0 thread
     
115. wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.131.59.cpe4.16L04_CT2015_Yueme.0-wapi-kdb
     
116. dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
     
117. dhd_module_init in
     
118. dhd_queue_budget = 256
     
119. dhd_sta_threshold = 2048
     
120. dhd_if_threshold = 65536
     
121. no wifi platform data, skip
     
122. Broadcom PCI Device 0x6300 has allocated with driver ohci_hcd
     
123. Broadcom PCI Device 0x6300 has allocated with driver ehci_hcd
     
124. Broadcom PCI Device 0x005b has allocated with driver pcieport
     
125. Broadcom PCI Device 0xa8db has allocated with driver wl
     
126. dhdpcie_bus_register: dhdpcie initialize failed.
     
127. dhd_module_init: Failed to load the driver, try cnt 3
     
128. no wifi platform data, skip
     
129. Broadcom PCI Device 0x6300 has allocated with driver ohci_hcd
     
130. Broadcom PCI Device 0x6300 has allocated with driver ehci_hcd
     
131. Broadcom PCI Device 0x005b has allocated with driver pcieport
     
132. Broadcom PCI Device 0xa8db has allocated with driver wl
     
133. dhdpcie_bus_register: dhdpcie initialize failed.
     
134. dhd_module_init: Failed to load the driver, try cnt 2
     
135. no wifi platform data, skip
     
136. Broadcom PCI Device 0x6300 has allocated with driver ohci_hcd
     
137. Broadcom PCI Device 0x6300 has allocated with driver ehci_hcd
     
138. Broadcom PCI Device 0x005b has allocated with driver pcieport
     
139. Broadcom PCI Device 0xa8db has allocated with driver wl
     
140. dhdpcie_bus_register: dhdpcie initialize failed.
     
141. dhd_module_init: Failed to load the driver, try cnt 1
     
142. no wifi platform data, skip
     
143. Broadcom PCI Device 0x6300 has allocated with driver ohci_hcd
     
144. Broadcom PCI Device 0x6300 has allocated with driver ehci_hcd
     
145. Broadcom PCI Device 0x005b has allocated with driver pcieport
     
146. Broadcom PCI Device 0xa8db has allocated with driver wl
     
147. dhdpcie_bus_register: dhdpcie initialize failed.
     
148. dhd_module_init: Failed to load the driver, try cnt 0
     
149. dhd_module_init: Failed to load driver max retry reached**
     
150. dhd_module_init out
     
151. insmod: can't insert '/lib/modules/3.4.11-rt19/extra/dhd.ko': Operation not permitted
     
152. Initializing USB Mass Storage driver...
     
153. usbcore: registered new interface driver usb-storage
     
154. USB Mass Storage support registered.
     
155. usbcore: registered new interface driver usbserial
     
156. usbcore: registered new interface driver usbserial_generic
     
157. USB Serial support registered for generic
     
158. usbserial: USB Serial Driver core
     
159. usbcore: registered new interface driver pl2303
     
160. USB Serial support registered for pl2303
     
161. usbcore: registered new interface driver ftdi_sio
     
162. USB Serial support registered for FTDI USB Serial Device
     
163. ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
     
164. usbcore: registered new interface driver cp210x
     
165. USB Serial support registered for cp210x
     
166. usbcore: registered new interface driver ch341
     
167. USB Serial support registered for ch341-uart
     
168. usbcore: registered new interface driver cdc_acm
     
169. cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
     
170. Broadcom 802.1Q VLAN Interface, v0.1
     
171. brcm_otp_init entry
     
172. Board not populated with PMD
     
173. RDPA Speed Service Command Driver
     
174. rdpa filter init start!!
     
175. # Created object <filter>
     
176. rdpa filter init end
     
177. init i2c opt start
     
178. ERR: _bdmf_attr_string_split#389: can't parse attribute index for reason_cfg
     
179. ERR: bdmf_configure#1479: cpu/index=host: status:Parsing error. config:reason_cfg[{dir=ds,reason=etype_pppoe_d}={queue=4,meter=3}
     
180. Object configuration failed: Parsing error
     
181. MON: Bdmf/Configure> failed with error code Parsing error(-11)
     
182. i2c_debug initopt success
     
183. init i2c opt end
     
184. BOARDID=96848EG2F2V1_UX
     
185. insmod voice ko files......
     
186. Loading PCM shim driver
     
187. Endpoint: endpoint_init entry
     
188. Endpoint: endpoint_init COMPLETED
     
189. Configuring factorymode...
     
190. Saving kernel bootup messages for dumpsysinfo...
     
191. Starting CMS smd...
     
192. ===== Release Version 4.16L.04_CT2015_Yueme (build timestamp 230227_0544) =====
     
193. Initializing CMS MDM in Legacy98 mode
     
194. Got primary config file from flash (len=51516), validating....
     
195. config file from flash (__primaryPsi) is valid, len=51516, loading into MDM....
     
196. get uploadpre from psp is FALSE
     
197. mdm_loadConfig end
     
198. Adjust WLAN Configuration, has configuration [1], num [4], defaultnum [4]
     
199. ssk:error:45.276:mdm_restore_areacode_igd:1996:areacode_mdm is valid, areacode_mdm = G. Nothing done
     
200. ssk:error:45.343:mdm_restore_areacode_igd:2033:AreaCode config found!
     
201. ssk:error:45.343:mdm_restore_areacode_igd:2034:ptr_areatag_start = <AreaCode>G</AreaCode>
     
202. ptr_areatag_end = </AreaCode>
     
203. !
     
204. ssk:error:45.343:mdm_restore_areacode_igd:2045:areacode_precfg = G cp_len = 2!
     
205. ssk:error:45.344:mdm_restore_areacode_igd:2059:areacode_precfg is valid, areacode_precfg = G, restore now
     
206. ip_tables: (C) 2000-2006 Netfilter Core Team
     
207. nf_conntrack version 0.5.0 (3613 buckets, 14452 max)
     
208. ssk:error:47.289:rcl_fIBSambaManageObject:1038:Can not open /var/samba/smb.conf.
     
209. killall: gadi: no process killed
     
210. ssk:error:47.540:processOneDnsLine_New:468:activeIfName:
     
211. Host MIPS Clock divider pwrsaving is enabled
     
212. Energy Efficient Ethernet changed to disabled
     
213. get loid from psp error
     
214. get loidpassword from psp error
     
215. goto gadi_init ERROR
     
216. Sorry, rule does not exist.
     
217. read of forward table failed: No such device
     
218. Sorry, rule does not exist.
     
219. read of forward table failed: No such device
     
220. ssk:error:48.528:rutSntp_restart:549:ruobing----getVoipDnsServerIP failed
     
221. sntp:error:48.729:main:438:No timezone specified.
     
222. Netfilter messages via NETLINK v0.30.
     
223. br_netlink_mcpd.c: Setting registration type 0 pid to 855
     
224. Ethernet Auto Power Down and Sleep: Enabled
     
225. ADDRCONF(NETDEV_UP): eth0: link is not ready
     
226. ssk:error:50.910:rut_stopRadvd:1164:failed to remove
     
227. Ethernet Auto Power Down and Sleep: Enabled
     
228. ADDRCONF(NETDEV_UP): eth1: link is not ready
     
229. ssk:error:52.137:rut_stopRadvd:1164:failed to remove
     
230. Ethernet Auto Power Down and Sleep: Enabled
     
231. ADDRCONF(NETDEV_UP): eth2: link is not ready
     
232. ssk:error:53.298:rut_stopRadvd:1164:failed to remove
     
233. Ethernet Auto Power Down and Sleep: Enabled
     
234. ADDRCONF(NETDEV_UP): eth3: link is not ready
     
235. ssk:error:54.322:rut_stopRadvd:1164:failed to remove
     
236. ssk:error:54.840:rut_stopRadvd:1164:failed to remove
     
237. entry rcl_wanEponIntfObject
     
238. ifconfig: ioctl 0x8913 failed: No such device
     
239. entry rcl_wanPonIntfObject
     
240. entry rcl_wanEponIntfObject
     
241. ifconfig: ioctl 0x8913 failed: No such device
     
242. entry rcl_wanPonIntfObject
     
243. get ifname=ppp2.3, gateway=
     
244. Broadcom Packet Flow Cache flushing the flows
     
245. get ifname=ppp2.3, gateway=
     
246. Broadcom Packet Flow Cache flushing the flows
     
247. get ifname=, gateway=
     
248. ssk:error:55.904:rcl_l3ForwardingEntryObject:143:wan is not connected
     
249. get ifname=, gateway=
     
250. ssk:error:55.905:rcl_l3ForwardingEntryObject:143:wan is not connected
     
251. get ifname=, gateway=
     
252. ssk:error:55.905:rcl_l3ForwardingEntryObject:143:wan is not connected
     
253. get ifname=, gateway=
     
254. ssk:error:55.906:rcl_l3ForwardingEntryObject:143:wan is not connected
     
255. get ifname=, gateway=
     
256. ssk:error:55.907:rcl_l3ForwardingEntryObject:143:wan is not connected
     
257. get ifname=, gateway=
     
258. ssk:error:55.907:rcl_l3ForwardingEntryObject:143:wan is not connected
     
259. get ifname=, gateway=
     
260. ssk:error:55.908:rcl_l3ForwardingEntryObject:143:wan is not connected
     
261. get ifname=, gateway=
     
262. ssk:error:55.908:rcl_l3ForwardingEntryObject:143:wan is not connected
     
263. get ifname=, gateway=
     
264. ssk:error:55.909:rcl_l3ForwardingEntryObject:143:wan is not connected
     
265. get ifname=, gateway=
     
266. ssk:error:55.910:rcl_l3ForwardingEntryObject:143:wan is not connected
     
267. get ifname=, gateway=
     
268. ssk:error:55.910:rcl_l3ForwardingEntryObject:143:wan is not connected
     
269. get ifname=, gateway=
     
270. ssk:error:55.911:rcl_l3ForwardingEntryObject:143:wan is not connected
     
271. get ifname=, gateway=
     
272. ssk:error:55.912:rcl_l3ForwardingEntryObject:143:wan is not connected
     
273. get ifname=, gateway=
     
274. ssk:error:55.912:rcl_l3ForwardingEntryObject:143:wan is not connected
     
275. get ifname=, gateway=
     
276. ssk:error:55.913:rcl_l3ForwardingEntryObject:143:wan is not connected
     
277. get ifname=, gateway=
     
278. ssk:error:55.914:rcl_l3ForwardingEntryObject:143:wan is not connected
     
279. get ifname=, gateway=
     
280. ssk:error:55.914:rcl_l3ForwardingEntryObject:143:wan is not connected
     
281. get ifname=, gateway=
     
282. ssk:error:55.915:rcl_l3ForwardingEntryObject:143:wan is not connected
     
283. get ifname=, gateway=
     
284. ssk:error:55.915:rcl_l3ForwardingEntryObject:143:wan is not connected
     
285. get ifname=, gateway=
     
286. ssk:error:55.916:rcl_l3ForwardingEntryObject:143:wan is not connected
     
287. get ifname=, gateway=
     
288. ssk:error:55.917:rcl_l3ForwardingEntryObject:143:wan is not connected
     
289. get ifname=, gateway=
     
290. ssk:error:55.917:rcl_l3ForwardingEntryObject:143:wan is not connected
     
291. get ifname=, gateway=
     
292. ssk:error:55.918:rcl_l3ForwardingEntryObject:143:wan is not connected
     
293. get ifname=, gateway=
     
294. ssk:error:55.919:rcl_l3ForwardingEntryObject:143:wan is not connected
     
295. get ifname=, gateway=
     
296. ssk:error:55.919:rcl_l3ForwardingEntryObject:143:wan is not connected
     
297. /bin/smd:error:55.929:launchApp:1049:Could not find requested app smbd (eid=53), not launched!
     
298. ssk:error:55.930:rcl_networkServerObject:138:failed to start SAMBA server.
     
299. ssk:error:55.930:mdm_activateObjects:2282:rcl handler reports error=9002 on NetworkServer oid=804 iidStack={1}
     
300. init user limit module
     
301. user_proc_init
     
302. user_num_max=253
     
303. ssk:error:56.672:rcl_igmpAuthenticationCfgObject:149:whitelist disable 0
     
304. Broadcom Packet Flow Cache Learning of GRE flows Tunnel<DISABLED> PassThru<ENABLED>
     
305. iptables: Bad rule (does a matching rule exist in that chain?).
     
306. iptables: Bad rule (does a matching rule exist in that chain?).
     
307. iptables: Bad rule (does a matching rule exist in that chain?).
     
308. iptables: Bad rule (does a matching rule exist in that chain?).
     
309. ip6_tables: (C) 2000-2006 Netfilter Core Team
     
310. ssk:error:58.760:[ERROR enet] bcmeapi_ioctl_ethsw_port_pause_capability,575: invalid lan port id 8
     
311. bcm_enet_map_oam_idx_to_phys_port:2826:Get unit port failed, oam_idx=8
     
312. ssk:error:58.770:bcm_port_pause_capability_set:1373:ioctl SIOCETHSWCTLOPS returned error 1 (Operation not permitted)
     
313. monitor task is initialized pid= 646
     
314. tr69c:error:60.208:oal_lock:226:lock currently held by pid=646 func=initAppConfig timeHold=759
     
315. tr69c:error:60.208:oal_lock:256:timeoutMs=10000
     
316. tr69c:error:60.358:oal_lock:226:lock currently held by pid=646 func=updateLinkStatus_igd timeHold=1
     
317. tr69c:error:60.359:oal_lock:256:timeoutMs=10000
     
318. got smdId=0rut_getdevmaxbandwidth_ds:0max_rate=0 min_rate=0
     
319. max_rate=0 min_rate=0
     
320. max_rate=0 min_rate=0
     
321. max_rate=0 min_rate=0
     
322. max_rate=0 min_rate=0
     
323. max_rate=0 min_rate=0
     
324. max_rate=0 min_rate=0
     
325. create tid2 thread succes, main pid is 646
     
326. call main_loop_back end
     
327. ssk:error:60.774:oal_lock:226:lock currently held by pid=1364 func=initTr069Control timeHold=71
     
328. ssk:error:60.775:oal_lock:256:timeoutMs=15000
     
329. p_area_code values is G.
     
330. Starting wanconf...
     
331. tr69c:error:60.972:oal_lock:226:lock currently held by pid=646 func=processWatchWanConnectionMsg timeHold=192
     
332. tr69c:error:60.972:oal_lock:256:timeoutMs=10000
     
333. The ponwiz(GPON)/omcapp(EPON) process is exit1
     
334. tr69c:error:61.532:oal_lock:226:lock currently held by pid=646 func=processWatchWanConnectionMsg timeHold=0
     
335. tr69c:error:61.532:oal_lock:256:timeoutMs=10000
     
336. tr69c:error:61.816:oal_lock:226:lock currently held by pid=646 func=processWatchWanConnectionMsg timeHold=131
     
337. tr69c:error:61.817:oal_lock:256:timeoutMs=10000
     
338. tr69c:error:61.890:oal_lock:226:lock currently held by pid=646 func=processWatchWanConnectionMsg timeHold=0
     
339. tr69c:error:61.890:oal_lock:256:timeoutMs=10000
     
340. wanconf: cmsPsp_get: rdpaWanTyscratchpad RdpaWanType - EPON
     
341. pe=EPON
     
342. scratchpad EponSpeed - Normal
     
343. factory mode is disabled, exit!optarg=0 shmId=0
     
344. ==========62.329590============[main, 306]
     
345. /bin/smd:error:62.470:interest_unregister:161:could not find record of msgType 0x10000254
     
346. start to init wifi diag thread !
     
347. finish init mutex g_wifi_mutex, start create thread !
     
348. wlmngr_getintfNo intf - wl0 exist !
     
349. ==========62.827460============[wl_start_setup, 1840]
     
350. epon_chrdev_init()
     
351. Creating CPU ring for queue number 5 with 32 packets descriptor=0xc047cc68
     
352. Done initializing Ring 5 Base=0xa8f9db80 End=0xa8f9dd80 calculated entries= 32 RDD Base=0x08f9db80 descriptor=0xc047cc68
     
353. starting pid 1507, tty '': '-/bin/sh -l -c consoled'
     
354. ERR: bdmf_attreleEponOamQueueOpen
     
355. Creating CPU ring for queue number 6 with 64 packets descriptor=0xc047cc90
     
356. Done initializing Ring 6 Base=0xa8074080 End=0xa8074480 calculated entries= 64 RDD Base=0x08074080 descriptor=0xc047cc90
     
357. m_set_as_num#1103: cpu/index=host: status:Entry doesn't exist. attribute:rxq_flush  value:1
     
358. cpu Ring 6 has been flushed
     
359. EponCaptureEapolToOamQueue
     
360. cpu Ring 6 has been flushed
     
361. dgasp: kerSysRegisterDyingGaspHandler: epon registered
     
362. enable IH Wan-Wan forwarding...
     
363. BCM96848 Broadband Router
     
364. Sorry, rule does not exist.
     
365. in FH_SYSTEM,buf is START_APP:rm -rf /var/pontrafficlog0.txt
     
366. 0
     
367. in FH_SYSTEM,buf is START_APP:echo 0/0:0/0 >> /var/pontrafficlog0.txt
     
368. 0
     
369. access  in  areacode is beijing ,do nothing ...........................
     
370. iptables v1.6.2: Couldn't find target `PARENT_CTRL'
     
371. Try `iptables -h' or 'iptables --help' for more information.
     
372. iptables: No chain/target/match by that name.
     
373. iptables: No chain/target/match by that name.
     
374. smartagent:error:65.022:oal_lock:226:lock currently held by pid=1366 func=wlLockReadMdm timeHold=749
     
375. smartagent:error:65.022:oal_lock:256:timeoutMs=6000
     
376. ls: /fhlog/updateimage.txt: No such file or directory
     
377. NULL str
     
378. NULL str
     
379. fill_dev_extendedId start
     
380. omcip_COUNT2(gpon)=0
     
381. omcapp_COUNT2(epon)=1
     
382. partition =1
     
383. Port 6 is not declared
     
384. Ethernet Auto Power Down and Sleep: Enabled
     
385. Port 6 is not declared
     
386. Ethernet Auto Power Down and Sleep: Enabled
     
387. device wl0 is not a slave of br0
     
388. interface wl0.1 does not exist!
     
389. interface wl0.2 does not exist!
     
390. interface wl0.3 does not exist!
     
391. There is no Predefined DevicePin in CFE
     
392. WPS Device PIN = 90150104
     
393. psi does not change
     
394. Setting SSID: "CU_THPbbb"
     
395. Setting SSID: "GUEST_THPb"
     
396. Setting SSID: "STB_THPb"
     
397. Setting SSID: "BACKUP"
     
398. EponRogueDetInit
     
399. bbbb
     
400. CTC OAM stack registered
     
401. CtcFwUpgradeEnterIdle 189, free ctcSession.buffer!
     
402. TkExtOamTaskInit success!
     
403. psi does not change
     
404. acsd: scan in progress ...
     
405. acsd: scan in progress ...
     
406. acsd: scan in progress ...
     
407. acsd: scan in progress ...
     
408. acsd: scan in progress ...
     
409. acsd: scan in progress ...
     
410. acsd: scan in progress ...
     
411. acsd: scan in progress ...
     
412. acsd: scan in progress ...
     
413. acsd: scan in progress ...
     
414. acsd: scan in progress ...
     
415. ==========78.326541============[wl_start_setup, 1877]
     
416. WLmngr Daemon is running
     
417. ==========78.326729============[main, 388]
     
418. acsd: scan in progress ...
     
419. acsd: scan in progress ...
     
420. acsd: scan in progress ...
     
421. acsd: selected channel spec: 0x1809
     
422. acsd: Adjusted channel spec: 0x1909
     
423. acsd: selected channel spec: 0x1909
     
424. wl0 evt 8 STA ADDR: [40-ec-99-bb-28-5d] associated
     
425. wl0 evt c STA ADDR: [40-ec-99-bb-28-5d] leaving
     
426. gadi:error:167.510:processLanHostInfo_igd:1214:Send CMS_MSG_DHCPD_TO_QUICKINSTALL_DEVICE_OFFLINE ret=0
     
427. open file error!
     
428. wl: Not Found
     
429. wl: Bad Address
     
430. cat: can't open '/var/dhcp_mac': No such file or directory
     
431. gadi:error:168.783:getVendorIDByHostIid:194:failed to open the file
     
432. gadi:error:168.865:processOneDnsLine_New:468:activeIfName:
     
433. open file error!
     
434. wl0 evt 8 STA ADDR: [40-ec-99-bb-28-5d] associated
     
435. wl0 evt c STA ADDR: [40-ec-99-bb-28-5d] leaving
     
436. gadi:error:216.454:processLanHostInfo_igd:1214:Send CMS_MSG_DHCPD_TO_QUICKINSTALL_DEVICE_OFFLINE ret=0
     
437. open file error!
     
438. wl: Not Found
     
439. wl: Bad Address
     
440. cat: can't open '/var/dhcp_mac': No such file or directory
     
441. gadi:error:218.466:getVendorIDByHostIid:194:failed to open the file
     
442. gadi:error:218.556:processOneDnsLine_New:468:activeIfName:
     
443. open file error!
     
444. Login: root
     
445. Password: wlctl: wl driver adapter not found
     
446. wlctl: wl driver adapter not found
     
447. wlctl: wl driver adapter not found
     
448. wlctl: wl driver adapter not found
     
449. wlctl: wl driver adapter not found
     
450. wlctl: wl driver adapter not found
     
451. wlctl: wl driver adapter not found
     
452. wlctl: wl driver adapter not found
     
453. wlctl: wl driver adapter not found
     
454. wlctl: wl driver adapter not found
     
455. wlctl: wl driver adapter not found
     
456. wlctl: wl driver adapter not found
     
457. Login incorrect. Try again.
     
458. Login: root
     
459. Password:
     
460. Login incorrect. Try again.
     
461. Login: CMCCAdmin
     
462. Password:
     
463. Authorization failed after trying 3 times!!!.
     
464. wl0 evt 8 STA ADDR: [40-ec-99-bb-28-5d] associated
     
465. in FH_SYSTEM,buf is START_APP:echo 0/0:0/0 >> /var/pontrafficlog0.txt
     
466. 0
     
467. Login: Password: wl0 evt c STA ADDR: [40-ec-99-bb-28-5d] leaving
     
468. gadi:error:390.523:processLanHostInfo_igd:1214:Send CMS_MSG_DHCPD_TO_QUICKINSTALL_DEVICE_OFFLINE ret=0
     
469. open file error!
     
470. ssk:error:390.703:oal_lock:226:lock currently held by pid=796 func=processEthAssociateObj timeHold=178
     
471. ssk:error:390.703:oal_lock:256:timeoutMs=15000
     
472. wl: Not Found
     
473. wl: Bad Address
     
474. gadi:error:391.510:oal_lock:226:lock currently held by pid=646 func=processPeriodicTask timeHold=0
     
475. gadi:error:391.510:oal_lock:256:timeoutMs=15000
     
476. cat: can't open '/var/dhcp_mac': No such file or directory
     
477. gadi:error:391.575:getVendorIDByHostIid:194:failed to open the file
     
478. gadi:error:391.644:processOneDnsLine_New:468:activeIfName:
     
479. open file error!
     
480. wl0 evt 8 STA ADDR: [40-ec-99-bb-28-5d] associated
     
481. wl0 evt c STA ADDR: [40-ec-99-bb-28-5d] leaving
     
482. gadi:error:417.898:processLanHostInfo_igd:1214:Send CMS_MSG_DHCPD_TO_QUICKINSTALL_DEVICE_OFFLINE ret=0
     
483. open file error!
     
484. wl: Not Found
     
485. wl: Bad Address
     
486. cat: can't open '/var/dhcp_mac': No such file or directory
     
487. gadi:error:418.949:getVendorIDByHostIid:194:failed to open the file
     
488. gadi:error:419.018:processOneDnsLine_New:468:activeIfName:
     
489. open file error!
     
490. wl0 evt 8 STA ADDR: [40-ec-99-bb-28-5d] associated
     
491. cat: can't open '/var/online_report_mac': No such file or directory
     
492. gadi:error:434.196:processLanHostInfo_igd:1197:Send CMS_MSG_DHCPD_TO_QUICKINSTALL_DEVICE_ONLINE, ret=0
     
493. Login incorrect. Try again.
     
494. Login: user
     
495. Password:
     
496. Login incorrect. Try again.
     
497. Login: root
     
498. Password:
     
499. Authorization failed after trying 3 times!!!.
     
500. in FH_SYSTEM,buf is START_APP:echo 0/0:0/0 >> /var/pontrafficlog0.txt
     
501. 0

复制代码

bk3677

看出来了，固件是存在光猫内部的，和光纤没有直接关系。至于为什么不插光纤会导致重复引导的原因不详，可能是这个猫有对光纤接口的验证步骤。

idiu

bk3677 发表于 2024-3-6 19:52
我其实就是看上他有个Wi-Fi模块了，所以想看看能不能起死回生一下…

没啥用，烽火死了基本没救，隔壁论坛华为光猫说不定能找到固件，玩烽火的太少了，