|
本帖最后由 wagzc 于 2024-3-14 19:47 编辑
****************************
* FIRMWARE UPGRADING *
* DO NOT POWER OFF DEVICE! *
****************************
Executing: sf probe && sf update 0x44000000 0x6a0000 0x1b2054f
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
Failed to initialize SPI flash at 0:0
HTTP ugrade is done! Rebooting...
resetting ...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00086-IPQ60xxLZB-1
S - IMAGE_VARIANT_STRING=IPQ6018LA
S - OEM_IMAGE_VERSION_STRING=crm-ubuntu200
S - Boot Interface: NAND
S - Secure Boot: Off
S - Boot Config @ 0x000a602c = 0x000002e5
S - JTAG ID @ 0x000a607c = 0x001390e1
S - OEM ID @ 0x000a6080 = 0x00000000
S - Serial Number @ 0x000a4128 = 0x4a6549d5
S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000
S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000
S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021
S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009
S - PBL Patch Ver: 1
S - I-cache: On
S - D-cache: On
B - 3413 - PBL, Start
B - 592 - bootable_media_detect_entry, Start
B - 4339 - bootable_media_detect_success, Start
B - 5207 - elf_loader_entry, Start
B - 5380 - auth_hash_seg_entry, Start
B - 7846 - auth_hash_seg_exit, Start
B - 8344 - elf_segs_hash_verify_entry, Start
B - 103763 - elf_segs_hash_verify_exit, Start
B - 107955 - auth_xbl_sec_hash_seg_entry, Start
B - 108100 - auth_xbl_sec_hash_seg_exit, Start
B - 114640 - xbl_sec_segs_hash_verify_entry, Start
B - 114641 - xbl_sec_segs_hash_verify_exit, Start
B - 115571 - PBL, End
B - 97478 - SBL1, Start
B - 237229 - GCC [RstStat:0x10, RstDbg:0x700100] WDog Stat : 0x4
B - 239669 - clock_init, Start
D - 3019 - clock_init, Delta
B - 248788 - boot_flash_init, Start
D - 30378 - boot_flash_init, Delta
B - 281911 - sbl1_ddr_set_default_params, Start
D - 274 - sbl1_ddr_set_default_params, Delta
B - 288530 - boot_config_data_table_init, Start
D - 4758 - boot_config_data_table_init, Delta - (575 Bytes)
B - 298351 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0
B - 303200 - Image Load, Start
D - 6619 - OEM_MISC Image Loaded, Delta - (0 Bytes)
B - 312533 - Image Load, Start
D - 5063 - PMIC Image Loaded, Delta - (0 Bytes)
B - 320402 - sbl1_ddr_set_params, Start
B - 325404 - CPR configuration: 0x555
B - 328576 - Pre_DDR_clock_init, Start
D - 183 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 361364 - Image Load, Start
D - 427 - APDP Image Loaded, Delta - (0 Bytes)
B - 379389 - Image Load, Start
D - 427 - QTI_MISC Image Loaded, Delta - (0 Bytes)
B - 381799 - Image Load, Start
D - 793 - Auth Metadata
D - 702 - Segments hash check
D - 22631 - QSEE Dev Config Image Loaded, Delta - (36362 Bytes)
B - 406382 - Image Load, Start
D - 6801 - Auth Metadata
D - 10400 - Segments hash check
D - 332175 - QSEE Image Loaded, Delta - (1419184 Bytes)
B - 739015 - Image Load, Start
D - 640 - Auth Metadata
D - 1037 - Segments hash check
D - 34831 - RPM Image Loaded, Delta - (102800 Bytes)
B - 775523 - Image Load, Start
D - 701 - Auth Metadata
D - 3202 - Segments hash check
D - 124593 - APPSBL Image Loaded, Delta - (562788 Bytes)
B - 915732 - SBL1, End
D - 818559 - SBL1, Delta
S - Flash Throughput, 4000 KB/s (2122381 Bytes, 436718 us)
S - Core 0 Frequency, 800 MHz
S - DDR Frequency, 466 MHz
U-Boot 2016.01 (Dec 01 2021 - 11:02:07 +0800)
DRAM: smem ram ptable found: ver: 2 len: 4
256 MiB
NAND: ONFI device found
ID = 1580a101
Vendor = 1
Device = a1
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC: <NULL>: 0
PCI0 is not defined in the device tree
In: serial@78B1000
Out: serial@78B1000
Err: serial@78B1000
machid: 8030200
eth5 MAC Address from ART is not valid
Net: MAC0 addr:48:88:99:c7:d6:b8
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (0-0)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq6018_edma_alloc_rings: successfull
ipq6018_edma_setup_ring_resources: successfull
ipq6018_edma_configure_rings: successfull
ipq6018_edma_hw_init: successfull
eth0
Hit any key to stop autoboot: 0
ubi0: attaching mtd1
UBI init error 22
IPQ6018#
测试所有固件都是启动不了,uboot能进入,过渡固件也是不能启动,,,
uboot先刷的这个,启动不了,TTL刷的uboot-cmiot-ax18.bin,现在能进入uboot,刷固件无法启动
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?立即注册
×
|