|
|
西加云杉ac8210，小poe路由器cpu是7621的想刷op系统有没有好的办法刷机
原系统就是openwer的想这把原系统备份下在刷机一直找不到进管理系统的网址
接上串口可以在启动的时候刷固件刷uboot但是每找到备份固件的选项
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade bootloader
4. Upgrade bootloader (advanced mode)
5. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select
启动的信息########Check sks image validation:#########
Check sks image header magic OK
Bootloader CRC32 Checksum OK
#####We will use Backup Bootloader boot system.#####
device 0 offset 0x1000000, size 0x30000
SF: 196608 bytes @ 0x1000000 Read: OK
## Starting application at 0x80400000 ...
U-Boot 2018.09 (Feb 23 2021 - 14:18:45 +0800)
CPU: MediaTek MT7621AT ver 1, eco 3
Clocks: CPU: 880MHz, DDR: 1200MHz, Bus: 220MHz, XTAL: 40MHz
Model: MediaTek MT7621 reference board
DRAM: 256 MiB
Loading Environment from SPI Flash... *** Warning - bad CRC, using default environment
In: uartlite0@1e000c00
Out: uartlite0@1e000c00
Err: uartlite0@1e000c00
Net:
Warning: eth@1e100000 (eth0) using random MAC address - 66:32:35:58:26:53
eth0: eth@1e100000
Hit any key to stop autoboot: 0
#####Checking Primary Firmware######
########Check sks image validation:#########
Check sks image header magic OK
Check Sks image type Failed, sks_type = 806-os,type = MT7621-os
#####Primary is broken, Checking Backup Firmware######
########Check sks image validation:#########
Check sks image header magic OK
Check Sks image type Failed, sks_type = 806-os,type = MT7621-os
## Loading kernel from FIT Image at bfc90200 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: MIPS OpenWrt Linux-4.4.198
Type: Kernel Image
Compression: lzma compressed
Data Start: 0xbfc902e4
Data Size: 1840427 Bytes = 1.8 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x81001000
Entry Point: 0x81001000
Hash algo: crc32
Hash value: f9aba19d
Hash algo: sha1
Hash value: 4e36df5098d03df8207bb2bb1de0b7642a11505b
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at bfc90200 ...
Using 'config@1' configuration
Trying 'fdt@1' fdt subimage
Description: MIPS OpenWrt mt7621-rfb-ax-nor device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xbfe51950
Data Size: 11430 Bytes = 11.2 KiB
Architecture: MIPS
Hash algo: crc32
Hash value: 11f709ef
Hash algo: sha1
Hash value: 53a5b547914d733e12c42784b86a26bb19a67b92
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0xbfe51950
Uncompressing Kernel Image ... OK
Loading Device Tree to 8fe97000, end 8fe9cca5 ... OK
[ 0.000000] Linux version 4.4.198 (wanghonglei@BuildServer) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 25f1ac3+r49254) ) #3 SMP Tue Mar 22 14:25:33 CST 2022
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is MediaTek MT7621 RFB (802.11ax,SNOR)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff]
[ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 10 pages/cpu @817a8000 s8576 r8192 d24192 u40960
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00030dcf
[ 0.000000] Readback ErrCtl register=00030dcf
[ 0.000000] Memory: 253912K/262144K available (4231K kernel code, 237K rwdata, 816K rodata, 208K init, 213K bss, 8232K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007777] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.070402] pid_max: default: 32768 minimum: 301
[ 0.075114] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081639] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 3.831469] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 3.831479] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 3.831490] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 3.831631] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.177564] Synchronize counters for CPU 1: done.
[ 3.608246] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 3.608253] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 3.608259] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 3.608326] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.267892] Synchronize counters for CPU 2: done.
[ 3.698312] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 3.698318] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 3.698324] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 3.698400] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.353069] Synchronize counters for CPU 3: done.
[ 0.357805] Brought up 4 CPUs
[ 0.365485] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.375277] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.381565] pinctrl core: initialized pinctrl subsystem
[ 0.388125] NET: Registered protocol family 16
[ 0.427068] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.432730] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.438326] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.468105] clocksource: Switched to clocksource GIC
[ 0.474904] NET: Registered protocol family 2
[ 0.480042] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.486931] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.493376] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.499738] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.505488] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.512023] NET: Registered protocol family 1
[ 0.528054] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.534049] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.551003] io scheduler noop registered
[ 0.554841] io scheduler deadline registered (default)
[ 0.561004] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.568522] console [ttyS0] disabled
[ 0.572059] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 33, base_baud = 3125000) is a 16550A
[ 0.581094] console [ttyS0] enabled
[ 0.581094] console [ttyS0] enabled
[ 0.587976] bootconsole [early0] disabled
[ 0.587976] bootconsole [early0] disabled
[ 0.596445] 1e000d00.uartfull: ttyS1 at MMIO 0x1e000d00 (irq = 34, base_baud = 3125000) is a 16550A
[ 0.605967] 1e000e00.uartfull: ttyS2 at MMIO 0x1e000e00 (irq = 35, base_baud = 3125000) is a 16550A
[ 0.617325] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 0.624092] m25p80 spi0.0: mx25l25635e (32768 Kbytes)
[ 0.629280] 9 ofpart partitions found on MTD device spi0.0
[ 0.634763] Creating 9 MTD partitions on "spi0.0":
[ 0.639570] 0x000000000000-0x000002000000 : "ALL"
[ 0.645556] 0x000000000000-0x000000030000 : "Bootloader"
[ 0.652099] 0x000000030000-0x000000040000 : "Config"
[ 0.658248] 0x000000050000-0x000000090000 : "Factory"
[ 0.664427] 0x000000090000-0x000001000000 : "firmware"
[ 0.682483] 2 fit-fw partitions found on MTD device firmware
[ 0.688189] 0x000000090000-0x000000260000 : "kernel"
[ 0.694354] 0x000000260000-0x000001000000 : "rootfs"
[ 0.700471] mtd: device 6 (rootfs) set to be root filesystem
[ 0.706267] 1 squashfs-split partitions found on MTD device rootfs
[ 0.712493] 0x000000df0000-0x000001000000 : "rootfs_data"
[ 0.719091] 0x000001000000-0x000001030000 : "Bootloader2"
[ 0.725772] 0x000001030000-0x000001fa0000 : "firmware2"
[ 0.732179] 0x000001fa0000-0x000001fb0000 : "BoardInfo"
[ 0.738591] 0x000001fb0000-0x000001fc0000 : "RebootCause"
[ 0.745563] libphy: Fixed MDIO Bus: probed
[ 0.788358] libphy: mdio: probed
[ 0.792254] mtk_soc_eth 1e100000.ethernet: read MAC address 04:8b:42:2d:04:4d
[ 0.799881] mtk_soc_eth 1e100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 0.811007] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 10
[ 0.819551] mtk_soc_eth 1e100000.ethernet: read MAC address 04:8b:42:2d:04:4e
[ 0.827209] mtk_soc_eth 1e100000.ethernet: connected mac 1 to PHY at fixed-0:01 [uid=00000000, driver=Generic PHY]
[ 0.838474] mtk_soc_eth 1e100000.ethernet eth1: mediatek frame engine at 0xbe100000, irq 10
[ 0.847985] mt7621_wdt 1e000100.wdt: Initialized
[ 0.854918] NET: Registered protocol family 10
[ 0.860838] NET: Registered protocol family 17
[ 0.865354] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.878039] Bridge firewalling registered
[ 0.882077] 8021q: 802.1Q VLAN Support v1.8
[ 0.887084] crashlog::crashlog_init_fs Crashlog allocated RAM at address 0x3f00000
[ 0.951085] crashlog::save_to_flashfs RSTSTAT_REG[be000038]=[0xc0030000]
[ 0.957802] crashlog::write_reboot_cause_to_db ntp_updated = 0
[ 0.964121] crashlog::write_reboot_cause_to_db init_recognition = 0xab
[ 0.970660] crashlog::write_reboot_cause_to_db recorded = 0
[ 0.976922] crashlog::write_reboot_cause_to_db next_cause_slot = 20/12
[ 0.983542] crashlog::write_reboot_cause_to_db next_panic_slot = 2/0
[ 0.989989] crashlog::write_reboot_cause_to_db panic slot:
[ 0.995295] 0 0
[ 1.134421] random: nonblocking pool is initialized
[ 1.448229] mt753x gsw: Switch is MediaTek MT7530 rev 1
[ 1.474950] libphy: mt753x_mdio: probed
[ 1.478938] product model info : AC8210
[ 1.999180] RTL switch init failed:-1
[ 2.002932] fail to rtl8367s_hw_init
[ 2.007116] hctosys: unable to open rtc device (rtc0)
[ 2.022366] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 2.030031] Freeing unused kernel memory: 208K
[ 2.034482] This architecture does not have kernel memory protection.
[ 2.800802] init: Console is alive
[ 2.804456] init: - watchdog -
[ 4.828560] init: - preinit -
[ 5.436016] mt753x gsw: Port 0 Link is Up - 1Gbps/Full
/usr/bin/gtk_led_ctl.sh: line 169: l: not found
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
Before mount_root
[ 9.002888] mount_root: loading kmods from internal overlay
[ 9.851578] jffs2: notice: (471) jffs2_build_xattr_subsystem: complete building xattr subsystem, 5 of xdatum (0 unchecked, 5 orphan) and 5 of xref (0 dead, 5 orphan) found.
[ 9.867797] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 9.885085] block: extroot: not configured
[ 10.064509] jffs2: notice: (468) jffs2_build_xattr_subsystem: complete building xattr subsystem, 5 of xdatum (0 unchecked, 5 orphan) and 5 of xref (0 dead, 5 orphan) found.
[ 10.673466] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 10.688230] block: extroot: not configured
[ 10.739194] mount_root: overlay filesystem has not been fully initialized yet
[ 10.746421] mount_root: switching to jffs2 overlay
After mount_root
[ 10.788999] procd: - early -
[ 10.792019] procd: - watchdog -
[ 11.478645] procd: - ubus -
[ 12.492793] procd: - init -
Please press Enter to activate this console.
[ 31.098180] create shared memory "fp_shared"(size=10683392) success.
[ 31.871344] layer2_isolate_query module load
有么有大神给看看不上编程器好不好刷
|
|
/2 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2024-6-3 17:24
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
