TTL无法中断跑码

chupan

U-Boot 2016.01 (Jul 15 2021 - 11:41:08 +0000), Build: jenkins-common_router_openwrt_ota_publish-1523

DRAM:  smem ram ptable found: ver: 1 len: 4
256 MiB
USB: Node Not found, skipping initia▒*9▒  QPIC controller support serial NAND
ID = 41c841c8
Vendor = c8
Device = 41
Serial Nand Device Found With ID : 0xc8 0x41
Serial NAND device Manufacturer:GD5F1GQ5REYIG
Device Size:256 MiB, Page size:2048, Spare Size:128, ECC:8-bit
qpic_nand: changing oobsize to 80 from 128 bytes
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In:    serial@78AF000
Out:   serial@78AF000
Err:   serial@78AF000
machid: 8040000
### main_loop: bootcmd="bootmiwifi"
Hit any key to stop autoboot:  0
  miwifi: check crash in rmem !
trigger button release!
boot from rootfs 1
ubi0: attaching mtd1
ubi0: scanning is finished
UBI init error 22
Erasing NAND...
Erasing at 0x4e0000 -- 100% complete.
Writing to NAND... OK
resetting ...

chupan

一直重启无法中断，救砖工具也不行

chupan

U-Boot 2016.01 (Jul 15 2021 - 11:41:08 +0000), Build: jenkins-common_router_openwrt_ota_publish-1523

DRAM:  smem ram ptable found: ver: 1 len: 4
256 MiB
USB: Node Not found, skipping initia▒*9▒  QPIC controller support serial NAND
ID = 41c841c8
Vendor = c8
Device = 41
Serial Nand Device Found With ID : 0xc8 0x41
Serial NAND device Manufacturer:GD5F1GQ5REYIG
Device Size:256 MiB, Page size:2048, Spare Size:128, ECC:8-bit
qpic_nand: changing oobsize to 80 from 128 bytes
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In:    serial@78AF000
Out:   serial@78AF000
Err:   serial@78AF000
machid: 8040000
### main_loop: bootcmd="bootmiwifi"
Hit any key to stop autoboot:  0
  miwifi: check crash in rmem !
detect button press, continue check 5 secs
detect button pressed 5 secs !
confirm to launch xq_upgrade !
cmd=dhcp

Net:   cmbblk is stable 5
MAC0 addr:d4:35:38:5c:25:5a
PHY ID1: 0x4d
PHY ID2: 0xd0c0
MAC1 addr:d4:35:38:eb:53:6e
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init  done
eth0, eth1
Trying to ping server.....
eth0  Down Speed :10 Half duplex
Port1 Down Speed :10M Half duplex
ping failed; host 192.168.31.100 is not alive
eth0  Down Speed :10 Half duplex
Port1 Down Speed :10M Half duplex
ping failed; host 192.168.31.100 is not alive
eth0  Down Speed :10 Half duplex
Port1 Up Speed :10M Half duplex
Using eth1 device

救砖工具卡这