红米AX6变砖TTL连接无法中断

本拉登他祖宗

求助各位大佬，事情是这样的，我的这台红米AX6路由器没有刷过机，一直都是正常使用的，突然有一天无线搜索不到，网线也连接不上，上电 SYS 黄灯常亮，过会儿双黄灯闪一下又开始 SYS 黄灯常亮，然后重复。

下面是我拆机后，使用FT232RL烧录模块，通过TTL连接路由器的跑马日志，按照论坛救砖教程无法中断请问还有救吗？
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAAA
S - OEM_IMAGE_VERSION_STRING=xiaoyang-gv
S - Boot Config, 0x000002e5
B -       201 - PBL, Start
B -      2736 - bootable_media_detect_entry, Start
B -      3444 - bootable_media_detect_success, Start
B -      3448 - elf_loader_entry, Start
B -      6118 - auth_hash_seg_entry, Start
B -      6360 - auth_hash_seg_exit, Start
B -     68622 - elf_segs_hash_verify_entry, Start
B -    131321 - PBL, End
B -    145912 - SBL1, Start
B -    199744 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    206393 - pm_device_init, Start
B -    330528 - PM_SET_VAL:Skip
D -    123494 - pm_device_init, Delta
B -    332846 - pm_driver_init, Start
D -      5368 - pm_driver_init, Delta
B -    339282 - clock_init, Start
D -      2135 - clock_init, Delta
B -    343277 - boot_flash_init, Start
D -     11895 - boot_flash_init, Delta
B -    358954 - boot_config_data_table_init, Start
D -      3202 - boot_config_data_table_init, Delta - (575 Bytes)
B -    366488 - Boot Setting :  0x00000600
B -    370422 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16
B -    377346 - sbl1_ddr_set_params, Start
B -    381158 - CPR configuration: 0x300
B -    384544 - cpr_init, Start
B -    387441 - Rail:0 Mode: 5 Voltage: 808000
B -    392596 - CL CPR settled at 760000mV
B -    395402 - Rail:1 Mode: 5 Voltage: 880000
B -    399580 - Rail:1 Mode: 7 Voltage: 912000
D -     16470 - cpr_init, Delta
B -    406473 - Pre_DDR_clock_init, Start
B -    410499 - Pre_DDR_clock_init, End
B -    413885 - DDR Type : PCDDR3
B -    419497 - do ddr sanity test, Start
D -      1037 - do ddr sanity test, Delta
B -    424346 - DDR: Start of HAL DDR Boot Training
B -    429074 - DDR: End of HAL DDR Boot Training
B -    434747 - DDR: Checksum to be stored on flash is -822398634
B -    445178 - Image Load, Start
D -    224053 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -    669322 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    677008 - Image Load, Start
D -     10706 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -    687805 - Image Load, Start
D -     25254 - RPM Image Loaded, Delta - (105964 Bytes)
B -    713120 - Image Load, Start
D -     96716 - APPSBL Image Loaded, Delta - (590292 Bytes)
B -    809958 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    815753 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -    822158 - SBL1, End
D -    678564 - SBL1, Delta
S - Flash Throughput, 6749 KB/s  (2096771 Bytes,  310637 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz




U-Boot 2016.01 (Jul 08 2021 - 07:16:48 +0000), Build: jenkins-common_router_openwrt_ota_publish-1455


DRAM:  smem ram ptable found: ver: 1 len: 4
512 MiB
NAND:  ONFI device found
ID = 158061c8
Vendor = c8
Device = 61
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:   sdhci: Node Not found, skipping initialization


PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
Boot failure detected on both systems
machid: 8010010
MMC Device 0 not found
eth5 MAC Address from ART is not valid
write phy_id=1, reg(0x8074):0xffff
write phy_id=2, reg(0x8074):0xffff
write phy_id=3, reg(0x8074):0xffff
write phy_id=4, reg(0x8074):0xffff
bootwait is off, bootdelay=5
Hit any key to stop autoboot:  0
trigger button release!
Boot failure detected on both systems
boot from rootfs 1
  miwifi: check crash in rmem !
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 35 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 286, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 63948802
ubi0: available PEBs: 38, total reserved PEBs: 248, PEBs reserved for bad PEB handling: 20
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (4317184)
Could not find PCI in device tree
Boot failure detected on both systems
## Loading kernel from FIT Image at 44000000 ...
   Using 'config@ac04' configuration
   Trying 'kernel@1' kernel subimage
     Description:  ARM64 OpenWrt Linux-4.4.60
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x440000e8
     Data Size:    3957924 Bytes = 3.8 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41080000
     Entry Point:  0x41080000
     Hash algo:    crc32
     Hash value:   5d5b1135
     Hash algo:    sha1
     Hash value:   1292316badc394132e5700d41aa2b63c54fc7646
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
   Using 'config@ac04' configuration
   Trying 'fdt@ac04' fdt subimage
     Description:  ARM64 OpenWrt qcom-ipq807x-hkxx device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x443edb18
     Data Size:    79565 Bytes = 77.7 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   b4ed9ff8
     Hash algo:    sha1
     Hash value:   6119388eb1ae982f4a3586f267c7ea804db115bb
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x443edb18
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 4a3e9000, end 4a3ff6cc ... OK
Using machid 0x8010010 from environment

本拉登他祖宗

Starting kernel ...

Jumping to AARCH64 kernel via monitor
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.60 (jenkins@a9db012ab664) (gcc version 5.5.0 (OpenWrt GCC 5.5.0 unknown) ) #0 SMP PREEMPT Tue Feb 7 09:28:20 2023
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] Ignoring memory range 0x40000000 - 0x41000000
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc01ef5c000 s19096 r8192 d30056 u57344
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 105840
[    0.000000] Kernel command line: ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1
[    0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.000000] software IO TLB [mem 0x5fe57000-0x5fe97000] (0MB) mapped at [ffffffc01ee57000-ffffffc01ee96fff]
[    0.000000] Memory: 402204K/430080K available (5491K kernel code, 654K rwdata, 2796K rodata, 224K init, 405K bss, 27876K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0040000 - 0xffffffbdc0800000   (     7 MB actual)
[    0.000000]     fixed   : 0xffffffbffa7fd000 - 0xffffffbffac00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc01f000000   (   496 MB)
[    0.000000]       .init : 0xffffffc00089a000 - 0xffffffc0008d2000   (   224 KB)
[    0.000000]       .text : 0xffffffc000080000 - 0xffffffc0008997f4   (  8294 KB)
[    0.000000]       .data : 0xffffffc0008e1000 - 0xffffffc000984800   (   654 KB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000416] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000427] pid_max: default: 32768 minimum: 301
[    0.000516] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
[    0.000525] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes)
[    0.001055] Initializing cgroup subsys io
[    0.001072] Initializing cgroup subsys memory
[    0.001102] Initializing cgroup subsys devices
[    0.001117] Initializing cgroup subsys freezer
[    0.001128] Initializing cgroup subsys net_cls
[    0.001138] Initializing cgroup subsys pids
[    0.001387] EFI services will not be available.
[    0.001411] ASID allocator initialised with 65536 entries
[    0.051860] MSM Memory Dump base table set up
[    0.051885] MSM Memory Dump apps data table set up
[    0.090109] Detected VIPT I-cache on CPU1
[    0.090154] CPU1: Booted secondary processor [410fd034]
[    0.120094] Detected VIPT I-cache on CPU2
[    0.120121] CPU2: Booted secondary processor [410fd034]
[    0.150121] Detected VIPT I-cache on CPU3
[    0.150148] CPU3: Booted secondary processor [410fd034]
[    0.150200] Brought up 4 CPUs
[    0.150225] SMP: Total of 4 processors activated.
[    0.150235] CPU: All CPU(s) started at EL1
[    0.150259] alternatives: patching kernel code
[    0.167047] DMI not present or invalid.
[    0.167288] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.167312] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.167535] pinctrl core: initialized pinctrl subsystem
[    0.168481] NET: Registered protocol family 16
[    0.190050] cpuidle: using governor ladder
[    0.220066] cpuidle: using governor menu
[    0.220210] vdso: 2 pages (1 code @ ffffffc0008e9000, 1 data @ ffffffc0008e8000)
[    0.220350] DMA: preallocated 256 KiB pool for atomic allocations
[    0.220444] CPU: unavail, SoC Version: 2.0
[    0.220480] <CORE> glink_init: IPC Logging Disabled
[    0.220880] IPC logging disabled
[    0.220886] IPC logging disabled
[    0.220891] IPC logging disabled
[    0.220895] IPC logging disabled
[    0.220900] IPC logging disabled
[    0.223607] Soc version is not 1, changing clock offsets
[    0.235003] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[    0.237043] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[    0.239229] msm_rpm_dev_probe: AP“师夷长技以制夷”PM communication over GLINK
[    0.240156] sps:sps is ready.
[    0.249920] qcom,cpr4-ap“师夷长技以制夷”egulator b018000.cpr4-ctrl: CPR valid fuse count: 2
[    0.256446] pps_core: LinuxPPS API ver. 1 registered
[    0.256458] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.256486] PTP clock support registered
[    0.256635] dmi: Firmware registration failed.
[    0.257960] Advanced Linux Sound Architecture Driver Initialized.
[    0.258602] clocksource: Switched to clocksource arch_sys_counter
[    0.261850] NET: Registered protocol family 2
[    0.262441] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.262502] TCP bind hash table entries: 4096 (order: 4, 65536 bytes)
[    0.262598] TCP: Hash tables configured (established 4096 bind 4096)
[    0.262651] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.262673] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.262845] NET: Registered protocol family 1
[    0.270461] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.270480] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.273741] io scheduler noop registered
[    0.273758] io scheduler deadline registered (default)
[    0.275888] 20000000.pci supply vdda not found, using dummy regulator
[    0.275968] 20000000.pci supply vdda_phy not found, using dummy regulator
[    0.276003] 20000000.pci supply vdda_refclk not found, using dummy regulator
[    0.276548] PCI host bridge /soc/pci@20000000 ranges:
[    0.276576]    IO 0x20200000..0x202fffff -> 0x20200000
[    0.276591]   MEM 0x20300000..0x20ffffff -> 0x20300000
[    1.308649] qcom-pcie 20000000.pci: phy link never came up
[    1.310193] qcom-pcie 20000000.pci: hostinit failed
[    1.310203] qcom-pcie 20000000.pci: cannot initialize host
[    1.310347] qcom-pcie: probe of 20000000.pci failed with error -110
[    1.315756] NET: Registered protocol family 27
[    1.315769] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled
[    1.315781] qmi_log_init: IPC Logging disabled
[    1.315787] qmi_log_init: IPC Logging disabled
[    1.315877] msm_rpm_log_probe: OK
[    1.316456] msm-dcc b3000.dcc: DCC XPU is not specified
[    1.316699] msm-dcc b3000.dcc: DCC SRAM dump setup failed
[    1.316722] msm-dcc b3000.dcc: jiffies_64: 0xffff8b52, cntvct_64: 0x65983ad
[    1.316734] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff80003cc004)
[    1.316744] msm-dcc b3000.dcc: gcnt_lo: 0x06598567(0xffffff80003cc000)
[    1.317289] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
[    1.317957] msm_serial 78b3000.serial: msm_serial: detected port #0
[    1.317993] msm_serial 78b3000.serial: uartclk = 3686400
[    1.318027] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) is a MSM
[    1.318044] msm_serial: console setup on port #0
[    2.053733] console [ttyMSM0] enabled
[    2.058699] msm_serial 78b1000.serial: msm_serial: detected port #1
[    2.061965] msm_serial 78b1000.serial: uartclk = 19200000
[    2.068036] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 78, base_baud = 1200000) is a MSM
[    2.073898] msm_serial: driver initialized
[    2.082376] msm_serial_hsl_init: driver initialized
[    2.095086] brd: module loaded
[    2.095765] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    2.098477] m25p80 spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff
[    2.105367] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x61
[    2.110610] nand: GigaDevice PSR1GA30DT
[    2.117080] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.120762] 16 ofpart partitions found on MTD device qcom_nand.0
[    2.128281] Creating 16 MTD partitions on "qcom_nand.0":
[    2.134461] 0x000000000000-0x000000100000 : "0:SBL1"
[    2.141412] 0x000000100000-0x000000200000 : "0:MIBIB"
[    2.146212] 0x000000200000-0x000000500000 : "0SEE"
[    2.152974] 0x000000500000-0x000000580000 : "0EVCFG"
[    2.155735] 0x000000580000-0x000000600000 : "0:RPM"
[    2.160710] 0x000000600000-0x000000680000 : "0:CDT"
[    2.165466] 0x000000680000-0x000000700000 : "0:APPSBLENV"
[    2.170340] 0x000000700000-0x000000800000 : "0:APPSBL"
[    2.176324] 0x000000800000-0x000000880000 : "0:ART"
[    2.180963] 0x000000880000-0x000000900000 : "bdata"
[    2.185685] 0x000000900000-0x000000980000 : "crash"
[    2.190538] 0x000000980000-0x000000a00000 : "crash_syslog"
[    2.195392] 0x000000a00000-0x000002dc0000 : "rootfs"
[    2.232319] mtd: device 12 (rootfs) set to be root filesystem
[    2.232644] mtdsplit: no squashfs found in "rootfs"
[    2.237046] 0x000002dc0000-0x000005180000 : "rootfs_1"
[    2.274177] 0x000005180000-0x000007040000 : "overlay"
[    2.301932] 0x000007040000-0x0000070c0000 : "rsvd0"
[    2.303531] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[    2.308467] libphy: Fixed MDIO Bus: probed
[    2.531851] qca-mdio 90000.mdio: Could not find phy-reset-gpio
[    2.531963] libphy: qca_mdio: probed
[    2.536704] qca-mdio 90000.mdio: qca-mdio driver was registered
[    2.540465] Unable to create IPC log context!
[    2.546268] cnss: Platform driver probed successfully.
[    2.550667] Skip QCA8074V1 in V2 platform
[    2.555591] cnss_genl: genl_register_family fail: -17
[    2.559582] cnss: CNSS genl init failed -17
[    2.564600] cnss: Platform driver probed successfully.
[    2.568743] i2c /dev entries driver
[    2.579380] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    2.579827] sdhci: Secure Digital Host Controller Interface driver
[    2.586876] sdhci: Copyright(c) Pierre Ossman
[    2.592892] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.597959] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
[    2.603096] ICE IRQ = 81
[    2.611614]
[    2.611614] Version Rollback Feature Disabled
[    2.614535] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000008b04000
[    2.619542] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04000
[    2.636807] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04000
[    2.652691] sps:BAM 0x0000000008b04000 is registered.[    2.660431] DEV CI test message
[    2.665128] subsys-restart: “师夷长技以制夷”_parse_restart_orders(): q6v5_m3 device has been added to q6v5-m3's restart group
[    2.667882] subsys-restart: “师夷长技以制夷”_parse_restart_orders(): q6v5_wcss device has been added to q6v5-m3's restart group
[    2.678376] remoteproc remoteproc0: q6v5-m3 is available
[    2.688805] SPMI VADC - Min ch: 0 Max ch: 15
[    2.695585] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000
[    2.698246] coresight-csr 6001000.csr: CSR initialized
[    2.705706] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000
[    2.710668] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000
[    2.718180] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000
[    2.725578] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000
[    2.732959] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000
[    2.740336] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000
[    2.747704] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000
[    2.755090] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000
[    2.762484] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000
[    2.769850] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000
[    2.777221] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000
[    2.784609] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000
[    2.791983] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000
[    2.799370] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000
[    2.806730] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000
[    2.814128] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000
[    2.821502] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000
[    2.829047] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000
[    2.836364] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000
[    2.843792] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000
[    2.851213] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000
[    2.858568] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000
[    2.865633] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000
[    2.882726] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000
[    2.898612] sps:BAM 0x0000000006044000 is registered.[    2.906232] coresight-tmc 6028000.tmc: TMC initialized
[    2.911059] coresight-tmc 6027000.tmc: TMC initialized
[    2.916174] coresight-funnel 6021000.funnel: FUNNEL initialized
[    2.921243] coresight-funnel 6100000.funnel: FUNNEL initialized
[    2.927033] coresight-funnel 6120000.funnel: FUNNEL initialized
[    2.932960] coresight-funnel 61a1000.funnel: FUNNEL initialized
[    2.939398] coresight-etm4x 619c000.etm: ETM 4.0 initialized
[    2.945065] coresight-etm4x 619d000.etm: ETM 4.0 initialized
[    2.951026] coresight-etm4x 619e000.etm: ETM 4.0 initialized
[    2.956682] coresight-etm4x 619f000.etm: ETM 4.0 initialized
[    2.961976] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized
[    2.967699] coresight-stm 6002000.stm: STM initialized
[    2.976263] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000
[    2.980139] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[    2.990501] Netfilter messages via NETLINK v0.30.
[    2.995350] ip_set: protocol 6
[    3.000632] NET: Registered protocol family 10
[    3.003636] NET: Registered protocol family 17
[    3.007314] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    3.011766] Bridge firewalling registered
[    3.024477] 8021q: 802.1Q VLAN Support v1.8
[    3.029917] <CORE> glink_core_register_transport: IPC Logging disabled
[    3.032471] qcom,cpr4-ap“师夷长技以制夷”egulator b018000.cpr4-ctrl: CPR valid fuse count: 2
[    3.038987] msm_glink_smem_native_xprt       rx fifo not found
[    3.046318] pmd9655_s3: supplied by e-smps1-reg
[    3.051931] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[    3.055978] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[    3.062591] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[    3.070240] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[    3.077731] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[    3.086894] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 704000 uV
[    3.093840] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 808000 uV
[    3.103871] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 704, quot_offset[ 7]=   0
[    3.113637] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 893, quot_offset[ 7]= 185
[    3.124583] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[    3.136693] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz
[    3.142299] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz
[    3.149566] DEV CI test message
[    3.158371] remoteproc remoteproc1: q6v5-wcss is available
[    3.161147] ubi0: attaching mtd13
[    3.350458] ubi0: scanning is finished
[    3.357096] ubi0: attached mtd13 (name "rootfs_1", size 35 MiB)
[    3.357116] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.361822] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.368762] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.375613] ubi0: good PEBs: 286, bad PEBs: 0, corrupted PEBs: 0
[    3.382389] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    3.388640] ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 63948802
[    3.395669] ubi0: available PEBs: 38, total reserved PEBs: 248, PEBs reserved for bad PEB handling: 20
[    3.404625] ubi0: background thread "ubi_bgt0d" started, PID 113
[    3.414617] hctosys: unable to open rtc device (rtc0)
[    3.445158]  crash_kernel_init, res rsvd1, 50700000, 400000, /reserved-memory/rsvd1@50700000
[    3.445192]  mtd dev crash, size 0x80000
[    3.453085]  crash_kernel_init,  crash init, res->start:50700000,crash_buf:0xffffff8001c80000,crash_buf_len 0x7ffe4, crash_avail_sz 0x80000
[    3.456750]  Crash kernel dumper registered ok!
[    3.469450]  crash_syslog_init, res rsvd2, 50b00000, 400000, /reserved-memory/rsvd2@50b00000
[    3.473930]  mtd dev crash_syslog, size 0x80000
[    3.483076]  crash_syslog_init,  crash init, crash_buf_len 0x3ffe4, crash_avail_sz 0x40000
[    3.487221]  Crash syslog dumper register ok!
[    3.495670] pmd9655_ldo11: disabling
[    3.500391] ALSA device list:
[    3.503603]   No soundcards found.
[    3.508881] VFS: Mounted root (squashfs filesystem) readonly on device 31:17.
[    3.509913] Freeing unused kernel memory: 224K (ffffffc00089a000 - ffffffc0008d2000)
[    3.517001] Freeing alternatives memory: 44K (ffffffc0008d2000 - ffffffc0008dd000)
[    3.867679] init: Console is alive
[    3.867795] init: - watchdog -

本拉登他祖宗

[    3.976671] random: nonblocking pool is initialized
[    4.986059] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.001717] usbcore: registered new interface driver usbfs
[    5.001768] usbcore: registered new interface driver hub
[    5.006166] usbcore: registered new device driver usb
[    5.012959] Button Hotplug driver version 0.4.1
[    5.019007] SCSI subsystem initialized
[    5.022726] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.025065] ehci-platform: EHCI generic platform driver
[    5.243996] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.244038] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    5.248526] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010
[    5.255999] xhci-hcd xhci-hcd.0.auto: irq 189, io mem 0x08a00000
[    5.265003] hub 1-0:1.0: USB hub found
[    5.270873] hub 1-0:1.0: 1 port detected
[    5.274600] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.278494] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    5.283857] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.291646] hub 2-0:1.0: USB hub found
[    5.299688] hub 2-0:1.0: 1 port detected
[    5.305956] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.309904] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.689600] mount_root: mounting /dev/root
[    8.741038] ubi1: attaching mtd14
[    8.901007] ubi1: scanning is finished
[    8.907625] ubi1: attached mtd14 (name "overlay", size 30 MiB)
[    8.907646] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    8.912351] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    8.919206] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[    8.926056] ubi1: good PEBs: 246, bad PEBs: 0, corrupted PEBs: 0
[    8.932834] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[    8.939085] ubi1: max/mean erase counter: 87/42, WL threshold: 4096, image sequence number: 369937606
[    8.946113] ubi1: available PEBs: 0, total reserved PEBs: 246, PEBs reserved for bad PEB handling: 20
[    8.955419] ubi1: background thread "ubi_bgt1d" started, PID 184
UBI device number 1, total 246 LEBs (31236096 bytes, 29.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
ubimkvol: error!: UBI device does not have free logical eraseblo[    8.984702] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 195
cks
[    9.022175] UBIFS (ubi1:0): recovery needed
[    9.123382] UBIFS (ubi1:0): recovery completed
[    9.123477] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "data"
[    9.126740] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    9.133953] UBIFS (ubi1:0): FS size: 26918912 bytes (25 MiB, 212 LEBs), journal size 1396736 bytes (1 MiB, 11 LEBs)
[    9.143911] UBIFS (ubi1:0): reserved for root: 1271446 bytes (1241 KiB)
[    9.154148] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID F960AB94-9E80-4FD4-BE4C-A7D8EC781DD6, small LPT model
2116+0 records in
2116+0 records out
2116 bytes (2.1KB) copied, 0.006194 seconds, 333.6KB/s
131072+0 records in
[    9.527267] urandom-seed: Seed file not found (/etc/urandom.seed)
131072+0 records out
131072 bytes (128.0KB) copied, 0.328974 seconds, 389.1KB/s
System fail flag set. Do etc recovery
WARNING: No etc_bak folder
*****ota: remove files in /etc/remove.conf *****
start do data_mount_fail_recover
[   10.574984] procd: - early -
[   10.575035] procd: - watchdog -
[   11.210021] procd: - watchdog -
[   11.210145] procd: - ubus -
[   11.262407] procd: - init -
Please press Enter to activate this console.
/etc/rc.d/S00sysfixtime: Mon Apr  1 13:38:15 UTC 2024
/etc/rc.d/S00wifi_fw_mount: 2116+0 records in
/etc/rc.d/S00wifi_fw_mount: 2116+0 records out
/etc/rc.d/S00wifi_fw_mount: 2116 bytes (2.1KB) copied, 0.006241 seconds, 331.1KB/s
/etc/rc.d/S00wifi_fw_mount: 131072+0 records in
/etc/rc.d/S00wifi_fw_mount: 131072+0 records out
/etc/rc.d/S00wifi_fw_mount: 131072 bytes (128.0KB) copied, 0.347922 seconds, 367.9KB/s
/etc/rc.d/S03cgroup_init: mount: mounting none on /dev/cgroup/mem failed: Resource busy
/etc/rc.d/S03cgroup_init: mount: mounting none on /dev/cgroup/net_cls failed: Resource busy
/etc/rc.d/S03cgroup_init: mount: mounting none on /dev/cgroup/cpu failed: Resource busy
/etc/rc.d/S09qca-iot: sh: write error: Invalid argument
/etc/rc.d/S09qca-iot: /etc/rc.common: line 154: can't create /sys/class/gpio/gpio/direction: nonexistent directory
/etc/rc.d/S09qca-iot: /etc/rc.common: line 154: can't create /sys/class/gpio/gpio/value: nonexistent directory
/etc/rc.d/S09qca-iot: /etc/rc.common: line 154: can't create /sys/class/gpio/gpio/value: nonexistent directory
/usr/bin/iotd[307]: Started iot daemon
[   11.828027] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.477561] nf_conntrack version 0.5.0 (3144 buckets, 40000 max)
[   12.477589] xqnss: extend init success!
[   12.489699] cfg80211: World regulatory domain updated:
[   12.489724] cfg80211:  DFS Master region: unset
[   12.493721] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   12.498334] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.507929] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   12.518559] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   12.525094] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   12.533065] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   12.542789] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   12.552247] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   12.560318] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   12.715389] ssdk_switch_device_num_init[998]:INFO:ess-switch dts node number: 1
[   12.719148] ssdk_dt_get_switch_node[836]:INFO:ess-switch DT exist!
[   12.726005] ssdk_dt_parse_access_mode[737]:INFO:switch_access_mode: local bus
[   12.732175] ssdk_dt_parse_access_mode[750]:INFO:switchreg_base_addr: 0x3a000000
[   12.739289] ssdk_dt_parse_access_mode[751]:INFO:switchreg_size: 0x1000000
[   12.746574] ssdk_dt_parse_mac_mode[242]:INFO:mac mode = 0x0
[   12.752995] ssdk_dt_parse_mac_mode[251]:INFO:mac mode1 = 0xff
[   12.758552] ssdk_dt_parse_mac_mode[260]:INFO:mac mode2 = 0xff
[   12.764306] ssdk_dt_parse_uniphy[279]:INFO:ess-uniphy DT exist!
[   12.770122] ssdk_dt_parse_intf_mac[683]:INFO:dp1 MAC 8c:de:f9:ad:9d:f5
[   12.775936] ssdk_dt_parse_intf_mac[683]:INFO:dp2 MAC 8c:de:f9:42:48:6e
[   12.782482] ssdk_dt_parse_intf_mac[683]:INFO:dp3 MAC 8c:de:f9:ad:9d:f5
[   12.788968] ssdk_dt_parse_intf_mac[683]:INFO:dp4 MAC 8c:de:f9:ad:9d:f5
[   12.795467] ssdk_dt_parse_intf_mac[683]:INFO:dp5 MAC 8c:de:f9:ad:9d:f5
[   12.802004] ssdk_plat_init start
[   12.880712] ssdk_ppe_clock_init[464]:INFO:ppe and uniphy clock init successfully!
[   12.883875] ssdk_probe[1884]:INFO:ess_rst doesn't exist!
[   12.891117] HPPE initializing...
[   12.892340] ssdk_phy_driver_init[300]:INFO:dev_id = 0, phy_adress = 0, phy_id = 0xffffffff phytype doesn't match
[   12.899722] ssdk_phy_driver_init[300]:INFO:dev_id = 0, phy_adress = 1, phy_id = 0xffffffff phytype doesn't match
[   12.909874] ssdk_phy_driver_init[300]:INFO:dev_id = 0, phy_adress = 2, phy_id = 0xffffffff phytype doesn't match
[   12.920025] ssdk_phy_driver_init[300]:INFO:dev_id = 0, phy_adress = 3, phy_id = 0xffffffff phytype doesn't match
[   12.930178] ssdk_phy_driver_init[300]:INFO:dev_id = 0, phy_adress = 4, phy_id = 0xffffffff phytype doesn't match
[   12.940306] regi_init[3411]:INFO:Initializing HPPE!!
[   13.168600] ssdk_ppe_reset_init[738]:INFO:ppe reset successfully!
[   13.175053] qca_hppe_tdm_hw_init[737]:INFO:tdm setup num=96
[   13.178317] qca_hppe_portctrl_hw_init[165]:INFO:Hawkeye PPE port initializing
[   13.294679] ssdk_switch_register[1623]:INFO:Chip version 0x1500
[   13.297660] qca_link_polling_select[1285]:INFO:link-polling-required node does not exist
[   13.303899] ssdk_switch_register[1648]:INFO:polling is selected
[   13.311632] regi_init[3415]:INFO:Initializing HPPE Done!!
[   13.316545] regi_init[3459]:INFO:qca-ssdk module init succeeded!
[   13.323760] tun: Universal TUN/TAP device driver, 1.6
[   13.324997] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   13.332673] EDMA ver 1 hw init
[   13.336239] EDMA HW Reset completed succesfully
[   13.339118] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[   13.343486] RxDesc:1 (15-15) RxFill:1 (7-7)
[   13.349274] libphy: PHY 90000.mdio:00 not found
[   13.352878] nss-dp: probe of 3a001000.dp1 failed with error -14
[   13.357439] libphy: PHY 90000.mdio:01 not found
[   13.363304] nss-dp: probe of 3a001200.dp2 failed with error -14
[   13.367854] libphy: PHY 90000.mdio:02 not found
[   13.373712] nss-dp: probe of 3a001400.dp3 failed with error -14
[   13.378270] libphy: PHY 90000.mdio:03 not found
[   13.384130] nss-dp: probe of 3a001600.dp4 failed with error -14
[   13.388698] libphy: PHY 90000.mdio:04 not found
[   13.394533] nss-dp: probe of 3a001800.dp5 failed with error -14
[   13.399235] **********************************************************
[   13.404946] * NSS Data Plane driver
[   13.411549] **********************************************************
[   13.418212] l2tp_core: L2TP core driver, V2.0
[   13.422227] l2tp_netlink: L2TP netlink interface
[   13.564165] nss_driver - fw of size 667888  bytes copied to load addr: 40000000, nss_id : 0
[   13.565859] Supported Frequencies -
[   13.571339] 187.2 MHz 748.8 MHz
[   13.577294] 1.4976 GHz [   13.578251]
[   13.580717] ffffffbffc62c680: meminfo init succeed
[   13.617121] node size 2 # items 4
[   13.617145] memory: 40000000 536870912 (avl 439037952) items 4 active_cores 2
[   13.619424] ffffffbffc62c680: nss core 0 booted successfully
[   13.627151] nss_driver - fw of size 265296  bytes copied to load addr: 40800000, nss_id : 1
[   13.633243] Supported Frequencies -
[   13.640344] 187.2 MHz 748.8 MHz
[   13.646307] 1.4976 GHz [   13.647265]
[   13.649709] ffffffbffc633780: meminfo init succeed
[   13.652912] sit: IPv6 over IPv4 tunneling driver
[   13.655391] node size 2 # items 4
[   13.655395] memory: 40000000 536870912 (avl 439037952) items 4 active_cores 2
[   13.655406] ffffffbffc633780: nss core 1 booted successfully
[   13.672487] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.
[   13.677176] gre: GRE over IPv4 demultiplexor driver
[   13.685131] ip_gre: GRE over IPv4 tunneling driver
[   13.690642] ip6_gre: GRE over IPv6 tunneling driver
[   13.696741] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   13.711844] QCA multicast snooping installed successfully
[   13.714317] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.490716] QCA Hy-Fi multicast installation successfully
[   16.149135] nss_lag_init[354]AG Manager Installed
[   16.700229] PPP generic driver version 2.4.2
[   16.700867] NET: Registered protocol family 24
[   17.039990] <NSS-CRYPTO>:module loaded Build_ID - 02/07/23, 10:53:10 SoC=ipq807x_64
[   17.270470] cannot find nss-macsec0 node
[   17.270533] cannot find nss-macsec1 node
[   17.273477] cannot find nss-macsec2 node
[   17.277356] nss_macsec init success
[   17.601833] diag: IPC Logging disabled
[   19.979235] u32 classifier
[   19.979256]     input device check on
[   19.980824]     Actions configured
[   20.409208] Mirror/redirect action on
[   25.279678] ipaccount: ifname [lo] event[5]
[   25.279711] ipaccount: ifname [miireg] event[5]
[   25.282659] ipaccount: ifname [ip6tnl0] event[5]
[   25.287174] ipaccount: ifname [sit0] event[5]
[   25.292076] ipaccount: ifname [gre0] event[5]
[   25.296289] ipaccount: ifname [gretap0] event[5]
[   25.300647] ipaccount: ifname [ip6gre0] event[5]
[   25.305318] ipaccount: ifname [bond0] event[5]
[   25.309951] ipaccount: ifname [teql0] event[5]
[   25.730993] fuse init (API version 7.23)
[   25.951292] ip_tables: (C) 2000-2006 Netfilter Core Team
[   25.953802] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   26.193404] PPP MPPE Compression module registered
[   26.194435] p p t p driver version 0.8.5
[   26.201254] ipt: xt_cgroup_MARK installed ok.
[   26.212102] xt_time: kernel timezone is -0000
[   26.221961] kmodloader: done loading kernel modules from /etc/modules.d/*
/etc/rc.d/S10boot: cp: omitting directory '/cfg/default/internal'
/etc/rc.d/S10boot: cat: can't open '/lib/wifi/wifi_nss_hk_olnum': No such file or d[   29.504248] configuring additional NSS pbufs
irectory
/etc/rc.d/S10boot: sh: 3: unknown operand

本拉登他祖宗

[   29.519102] additional pbufs of size 3100672 got added to NSS
[   29.540512] mem_manager: module license 'unspecified' taints kernel.
[   29.540539] Disabling lock debugging due to kernel taint
[   29.546806] __mm_init_module
[   29.570560] qdf_dbg_mask value is invalid
[   29.570583] Using the default module debug levels instead
[   29.573545] qdf_print_ctrl_register: Allocated print control object 0
[   29.579022]
MINIDUMP VA .bss start=ffffffbffcd39f00 module=qdf
[   30.037861] wlan: [1009:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50
[   30.037953]
MINIDUMP VA .bss start=ffffffbffcfcf100 module=umacINFO: Cold boot calibration not applicable: ap-ac04

[   30.201269]
[   30.201269]  MINIDUMP VA .bss start=ffffffbffd25ca00 module=qca_ol=======ol_if_register_wifi3_0==========
[   30.213815] wlan: [1021:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd390988
[   30.216458] remoteproc remoteproc0: powering up q6v5-m3
[   30.245466] remoteproc remoteproc0: Booting fw image IPQ8074/m3_fw.mdt, size 284
[   30.245498] Sanity check passed for M3 image
[   30.299751] remoteproc remoteproc0: remote processor q6v5-m3 is now up
[   30.299954] <“师夷长技以制夷”>: glink SUBSYS_BEFOER_POWERUP reinit done
[   30.305175] wlan: [1021:I:ANY] ol_ath_ahb_“师夷长技以制夷”: 183: ol_ath_ahb_“师夷长技以制夷”: “师夷长技以制夷” event 2
[   30.310681] remoteproc remoteproc1: powering up q6v5-wcss
[   30.318122] remoteproc remoteproc1: Booting fw image IPQ8074/q6_fw.mdt, size 668
[   30.323633] Sanity check passed for the image
[   31.422338] glink_core_link_up glink is up
[   31.422500] glink_xprt_open_event
[   31.422674] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled
[   31.428771] Subsystem error monitoring/handling services are up
[   31.435180] remoteproc remoteproc1: remote processor q6v5-wcss is now up
[   31.441294] cnss: QMI WLFW service connected, state: 0x1
[   31.441466] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, ffffffbffc916248
[   31.453145] wlan: [1021:I:ANY] ol_ath_ahb_“师夷长技以制夷”: 183: ol_ath_ahb_“师夷长技以制夷”: “师夷长技以制夷” event 3
[   31.462306] cnss: device_id : 0xfffe mem mode : [1]
[   31.470088] cnss: Boardid from dts:292,FW:ff
[   31.480517] cnss: BDF location : 0x000000004b0c0000
[   31.480544] cnss: BDF IPQ8074/bdwlan.b292 size 131072
[   31.484587] cnss: BDF download response , result: 0, err: 0x0
[   31.489814] cnss: per device BDF location : 0x000000004b0e0000
[   31.495245] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000
[   31.502998] cnss: BDF download response , result: 0, err: 0x0
[   31.562786] wlan: [1021:I:ANY] pld_ahb_wlan_enable: 689: cnss_mode: Mission mode
[   31.571400] wlan: [1021:I:ANY] qca_napi_create: 357: qca_napi_create: napi instance 0 created on pipe 4
[   31.571695] wlan: [1021:I:ANY] __ol_ath_attach: 3068: Allocated soc ffffffc017d00880
[   31.579675] btcoex_support 0 wlan_prio_gpio 0
[   31.587688] wlan: [1021:E:CONFIG] cfg_uint_item_handler: 171: dp_int_timer_threshold_tx=1000 - Out of range [8, 100]; Using 1000
[   31.591965] wlan: [1021:E:CONFIG] cfg_uint_item_handler: 171: dp_rxdma_monitor_desc_ring=128 - Out of range [4096, 16384]; Using 4096
[   31.603593] wlan: [1021:I:ANY] osif_nss_wifi_soc_setup: 186: nss-wifili:#1 register wifili function for soc
[   31.615368] wlan: [1021:I:ANY] osif_nss_wifi_soc_setup: 198: nss register id -1 nss config 3 Target Type 18
[   31.625288] wlan: [1021:I:ANY] __ol_ath_attach: 3282: dev name soc0
[   31.635231] wlan: [1021:I:ANY] ol_ath_soc_attach: 6564: WMI attached. wmi_handle ffffffc01a8e9400
[   31.641135] wlan: [1021:I:ANY] htc_wmi_init: 5931: htc_wmi_init() HT Create . ffffffc018fea000
[   31.650087] wlan: [1021:I:ANY] htc_wmi_init: 5938: htc_wmi_init() Skipping BMI Done.
[   31.658678] wlan: [1021:I:ANY] htc_wmi_init: 5995: [htc_wmi_init:5995] host_enable 0 nss_nwifi_offload 0
[   31.669926] wlan: [1021:I:ANY] ol_target_init_complete: 6113: CDP soc attach success
[   31.676122] wlan: [1021:I:ANY] ol_target_init_complete: 6120: Soc attach success NSS config 0
[   31.683906] wlan: [1021:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc018fea000, ep 2, value 1
[   31.692321] wlan: [1021:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc018fea000, ep 3, value 1
[   31.703153] wlan: [230:I:TIF] HE_CAP Info = 1a08010d
[   31.713018] wlan: [230:I:TIF] Num HW modes = 1
[   31.718059] wlan: [230:I:TIF] Num PHY = 2
[   31.722321] wlan: [230:I:TIF] Preferred HW Mode = 1 Num Radios = 2
[   31.726398] wlan: [230:I:TIF] init_deinit_add_11ax_modes: 1403: Adding 11ax regulatory modes,
[   31.732495] wlan: [230:I:TIF] init_deinit_add_11ax_modes: 1406:  phy_id = 0 wireless modes = f97f9001
[   31.741109] wlan: [230:I:TIF] init_deinit_add_11ax_modes: 1403: Adding 11ax regulatory modes,
[   31.750360] wlan: [230:I:TIF] init_deinit_add_11ax_modes: 1406:  phy_id = 1 wireless modes = 680680c
[   31.759079] wlan: [230:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 390: dfs_offload 1
[   31.768031] wlan: [230:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1038: dfs->dfs_psoc_idx: 0
[   31.777808] wlan: [230:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1044: dfs_soc_obj->num_dfs_privs: 1
[   31.787814] wlan: [230:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 362: Do not allocate DFS object for 2G, pdev_id = 1
[   31.805106] wlan: [230:I:TIF] init_deinit_update_pdev_tgt_info: 1064: CDP PDEV ATTACH success
[   31.812943] wlan: [230:I:TIF] init_deinit_update_pdev_tgt_info: 1064: CDP PDEV ATTACH success
[   31.920103] wlan: [230:I:ANY] copy_fw_abi_version_tlv: 6258: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0
[   32.050286] wlan: [230:I:ANY] dp_peer_map_attach_wifi3: 9979: dp_peer_map_attach_wifi3 max_peers 311, max_ast_index: 1040
[   32.050286]
[   32.050400] wlan: [230:I:ANY] ready_extract_init_status_tlv: 8002: ready_extract_init_status_tlv:0
[   32.061692] wlan: [1021:I:ANY] ol_ath_connect_htc: 1225: WMI is ready
[   32.122954] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 37 is unavailable
[   32.122993] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 141 is unavailable
[   32.130507] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 137 is unavailable
[   32.139012] wlan: [1021:I:ANY] ol_ath_soc_attach: 6638: connect HTC
[   32.147555] wlan: [1021:I:ANY] ol_ath_soc_attach: 6639: bypasswmi : 0
[   32.153736] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 38 is unavailable
[   32.160325] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 138 is unavailable
[   32.168832] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 139 is unavailable
[   32.177340] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 55 is unavailable
[   32.185936] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 49 is unavailable
[   32.194533] wlan: [1021:E:WMI] wmi_unified_register_event_handler: Event id 25 is unavailable
[   32.203035] wlan: [1021:I:ANY] ol_ath_soc_attach: 6714: ol_ath_soc_attach() UMAC attach .
[   32.211543]  *skip LOWI socket init, save id22 for ALD*
[   32.219775] wlan: [1021:I:ANY] __ol_ath_attach: 3401: pdev_netdev name wifi0
[   32.225174] wlan: [1021:I:ANY] __ol_ath_attach: 3446: Skip txrx_pdev_attach_target
[   32.232290] wlan: [1021:I:ANY] __ol_ath_attach: 3470: BURSTING enabled by default
[   32.239732] wlan: [1021:I:ANY] ol_ath_pdev_attach: 7179: interface_id 0
[   32.247216] wlan: [1021:I:ANY] ol_ath_pdev_regdmn_init: 6868:  phy id = 0 Modes supported
[   32.253649] wlan: [1021:I:ANY] ol_ath_pdev_regdmn_init: 6875:  11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1
[   32.261982] wlan: [1021:I:ANY] ol_ath_pdev_regdmn_init: 6883:  Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4910, hi_5g = 6100
[   32.272230] wlan: [1021:I:ANY] ol_ath_update_wireless_modes: 1324: wireless_modes = f97f9001 before update
[   32.286544] wlan: [1021:I:ANY] ol_ath_update_wireless_modes: 1339: Wireless_modes = f97f9001 after update
[   32.296266] wlan: [1021:I:ANY] ol_ath_update_ext_caps: 1850: 11ax 5G supported case
[   32.306032] wlan: [1021:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed
[   32.313429] ieee80211_cbs_init CBS Inited
[   32.323086] wlan: [1021:I:ANY] acfg_attach: 3457: acfg_attach: 3457: Netlink socket created:ffffffc018081800
[   32.323960] wlan: [1021:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX
[   32.334029] wlan: [1021:I:ANY] ol_ath_stats_attach: 2071: periodic_chan_stats: 1
[   32.345169] wlan: [1021:I:ANY] wlan_scan_update_channel_list: 1107: num_chan: 25
[   32.351585] wlan: [0:I:ANY] ol_ath_pdev_attach: 7515: Set global_ic[1], ptr:ffffffbffcfcf460
[   32.358939] wlan: [0:I:ANY] dp_lag_soc_enable: 88: pdev(ffffffc0173a8688) Enabling DBDC Repeater 1
[   32.367372] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ffffffc0173a8688) is_primary 1
[   32.367393] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[   32.385160] wlan: [1021:I:ANY] ol_ath_pdev_attach: 7632: Pdev = 0 Number of peers = 137
[   32.393485] wlan: [1021:I:ANY] ol_ath_twt_enable_command: 7031: TWT is disable in INI. Do not send enable cmd to FW
[   32.403736] wlan: [1021:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 589: ( 1) chan  36 blocked from cfg
[   32.411634] wlan: [1021:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 589: ( 2) chan 132 blocked from cfg
[   32.421400] wlan: [1021:I:ANY] osif_wrap_attach: 239: osif wrap attached
[   32.421400]
[   32.430813] wlan: [1021:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done
[   32.430813]
[   32.438888] wlan: [1021:I:ANY] osif_wrap_attach: 247:  Wrap Attached: Wrap_com =ffffffc018081c00 ic->ic_wrap_com=ffffffc018081c00 &wrap_com->wc_devt=ffffffc018081c00
[   32.438888]
[   32.448119] wlan: [1021:I:ANY] __ol_ath_attach: 3654: needed_headroom reservation 60
[   32.464406] wlan: [1021:I:ANY] ol_ath_enable_fraglist: 2935: Enabled Fraglist bit for the radio wifi0 features 41
[   32.472453] wlan: [1021:I:ANY] wlan_cfg80211_init: 9735: Number of 5G channels: 25
[   32.482790] wlan: [1021:I:ANY] ieee80211_cfg80211_radio_attach: 9829: ic: 0xffffffc0164c0880, wdev: 0xffffffc0164d0a70, wiphy: 0xffffffc0188e42a0, netdev: 0xffffffc0164c0000
[   32.490176] ipaccount: ifname [wifi0] event[16]
[   32.506149] ipaccount: ifname [wifi0] event[5]
[   32.510356] wlan: [1021:I:ANY] __ol_ath_attach: 3401: pdev_netdev name wifi1
[   32.514674] wlan: [1021:I:ANY] __ol_ath_attach: 3446: Skip txrx_pdev_attach_target
[   32.521910] wlan: [1021:I:ANY] __ol_ath_attach: 3470: BURSTING enabled by default
[   32.529330] wlan: [1021:I:ANY] ol_ath_pdev_attach: 7179: interface_id 1
[   32.536806] wlan: [1021:I:ANY] ol_ath_pdev_regdmn_init: 6868:  phy id = 1 Modes supported
[   32.543260] wlan: [1021:I:ANY] ol_ath_pdev_regdmn_init: 6875:  11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1
[   32.551581] wlan: [1021:I:ANY] ol_ath_pdev_regdmn_init: 6883:  Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0
[   32.561836] wlan: [1021:I:ANY] ol_ath_update_wireless_modes: 1324: wireless_modes = 680680c before update
[   32.576147] wlan: [1021:I:ANY] ol_ath_update_wireless_modes: 1339: Wireless_modes = 680680c after update
[   32.585780] wlan: [1021:I:ANY] ol_ath_update_ext_caps: 1858: 11ax 2G supported case
[   32.595467] wlan: [1021:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed
[   32.602762] ieee80211_cbs_init CBS Inited
[   32.612400] wlan: [1021:I:ANY] acfg_attach: 3432: Offload using existing sock ffffffc018081800
[   32.613279] wlan: [1021:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX
[   32.621965] wlan: [1021:I:ANY] ol_ath_stats_attach: 2071: periodic_chan_stats: 1
[   32.632508] wlan: [1021:I:ANY] wlan_scan_update_channel_list: 1107: num_chan: 11
[   32.639687] wlan: [0:I:ANY] ol_ath_pdev_attach: 7515: Set global_ic[2], ptr:ffffffbffcfcf460
[   32.647042] wlan: [0:I:ANY] dp_lag_soc_enable: 88: pdev(ffffffc015ada008) Enabling DBDC Repeater 1
[   32.655488] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ffffffc015ada008) is_primary 0
[   32.655514] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[   32.673277] wlan: [1021:I:ANY] ol_ath_pdev_attach: 7632: Pdev = 1 Number of peers = 137
[   32.681594] wlan: [1021:I:ANY] ol_ath_twt_enable_command: 7031: TWT is disable in INI. Do not send enable cmd to FW
[   32.690656] wlan: [1021:E:WMI] event handler already registered 0x6019
[   32.700647] wlan: [1021:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 589: ( 1) chan  36 blocked from cfg
[   32.706331] wlan: [1021:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 589: ( 2) chan 132 blocked from cfg
[   32.715996] wlan: [1021:I:ANY] osif_wrap_attach: 239: osif wrap attached
[   32.715996]
[   32.725432] wlan: [1021:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done
[   32.725432]
[   32.733509] wlan: [1021:I:ANY] osif_wrap_attach: 247:  Wrap Attached: Wrap_com =ffffffc018083000 ic->ic_wrap_com=ffffffc018083000 &wrap_com->wc_devt=ffffffc018083000
[   32.733509]
[   32.742738] wlan: [1021:I:ANY] __ol_ath_attach: 3654: needed_headroom reservation 60
[   32.759025] wlan: [1021:I:ANY] ol_ath_enable_fraglist: 2935: Enabled Fraglist bit for the radio wifi1 features 41
[   32.767025] wlan: [1021:I:ANY] wlan_cfg80211_init: 9723: Number of 2G channels: 11
[   32.777363] wlan: [1021:I:ANY] ieee80211_cfg80211_radio_attach: 9829: ic: 0xffffffc016500880, wdev: 0xffffffc016510a70, wiphy: 0xffffffc0188e72a0, netdev: 0xffffffc016500000
[   32.784774] ipaccount: ifname [wifi1] event[16]
[   32.800756] ipaccount: ifname [wifi1] event[5]
[   32.804940] ipaccount: ifname [soc0] event[16]
[   32.809658] ipaccount: ifname [soc0] event[5]
[   32.813772] wlan: [1021:I:ANY] wlan_pdev_operation: 735: num_radios=1, wifi_radios[0].sc = ffffffc0164c0880_radio_type = 2
[   32.818144] wlan: [1021:I:ANY] wlan_pdev_operation: 735: num_radios=2, wifi_radios[1].sc = ffffffc016500880_radio_type = 2
[   32.829139] wlan: [1021:I:ANY] init_ath_pci_3_0: 151: 6ath_ol_pci_wifi3.0:  (Atheros/multi-bss)
[   32.840209]
MINIDUMP VA .bss start=ffffffbffd390d80 module=wifi_3_0
[   32.867583] wlan: [1122:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd459858
[   32.867632] wlan: [1122:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd459858
[   32.879168] wlan: [1122:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0:  (Atheros/multi-bss)
No Direct-Attach chipsets found.
/etc/rc.d/S10boot: cat: can't open '1': No such file or directory
/etc/rc.d/S10boot: killall: acfg_tool: no process killed
/etc/rc.d/S10boot: /sbin/wifi: eval: line 1: /usr/sbin/acfg_tool: not found
/etc/rc.d/S10boot: odhcpd
/etc/rc.d/S10boot: system.cfg047450=rngd
/etc/rc.d/S10boot: system.cfg047450.enabled='0'
/etc/rc.d/S10boot: system.cfg047450.device='/dev/urandom'
/etc/rc.d/S10system: Changing password for root
/etc/rc.d/S10system: New password:
/etc/rc.d/S10system: Bad password: too weak
/etc/rc.d/S10system: Retype password:
/etc/rc.d/S10system: passwd: can't create '/etc/passwd+': File exists
/etc/rc.d/S10system: passwd: can't update password file /etc/passwd
[   38.240891] ipaccount: ifname [bond0] event[11]
/etc/rc.d/S15qca-wpa-supplicant: Successfully initialized wpa_supplicant
/etc/rc.d/S16qca-ssdk:
/etc/rc.d/S16qca-ssdk: starting
/etc/rc.d/S19dnsmasq: cp: can't stat '/etc/dnsmasq.d/*': No such file or directory
/etc/rc.d/S19dnsmasq: sh: out of range
/etc/rc.d/S19dnsmasq: sh: out of range
/etc/rc.d/S19dnsmasq: sed: /var/etc/dnsmasq.conf.cfg01411c: No such file or directory
/etc/rc.d/S19dnsmasq: sed: /var/etc/dnsmasq.conf.cfg01411c: No such file or directory
/etc/rc.d/S19firewall: /etc/rc.common: line 1: /usr/sbin/firewall.webinitrdr: not found
[   40.462401] ECM init
[   40.462457] ECM database jhash random seed: 0xcc69ff48
[   40.464754] qcaecm:   register  ecm_nss_ipv4_post_routing_hook()
[   40.468827] ECM init complete
/etc/rc.d/S19qca-nss-ecm: net.bridge.bridge-nf-call-ip6tables = 1
/etc/rc.d/S19qca-nss-ecm: net.bridge.bridge-nf-call-iptables = 1
/etc/rc.d/S19qca-nss-ecm: dev.nss.general.redirect = 1
/etc/rc.d/S20network: uci: Invalid argument
/etc/rc.d/S21nginx: start fcgi-cgi by spawn-fcgi.
/etc/rc.d/S21nginx: start nginx ok.
stopping miwifi-roam
/etc/init.d/network: Command failed: Not found
/etc/init.d/network: Command failed: Not found
lbd: stopping daemon
/etc/init.d/network: Command failed: Not found
/etc/rc.d/S49messagingagent.sh: start messagingagent ok.
/etc/rc.d/S50acd: acd *** not in cap/re mode, skip handle [   44.321589] ipaccount: ifname [lo] event[13]
[   44.323768] ipaccount: ifname [lo] event[1]

crond[2669]: crond (busybox 1.25.1) started, log level 5
/etc/init.d/network: File not preset
/etc/init.d/network: Failed to get common data
/etc/init.d/network: File not preset
/etc/init.d/network: Failed to get common data
/etc/init.d/network: Command failed: Not found
/etc/init.d/network: killall: iface-mgr: no process killed
/etc/init.d/network: killall: acfg_tool: no process killed
/etc/init.d/network: /sbin/wifi: eval: line 1: /usr/sbin/acfg_tool: not found
qcawificfg80211 disable radio wifi0
qcawificfg80211 disable radio wifi1
/etc/rc.d/S51cp_preinstall_plugins.sh: ls: /usr/share/datacenter/appdata/notuninstallable/app_infos: No such file or directory
/etc/rc.d/S51cp_preinstall_plugins.sh: ls: /usr/share/datacenter/appdata/uninstallable/app_infos: No such file or directory
/etc/init.d/network: device: wifi0 vifs: cfg023579
/etc/init.d/network: device: wifi1 vifs: cfg043579 miot_2G
/etc/init.d/network: killall: acfg_tool: no process killed
/etc/init.d/network: /sbin/wifi: eval: line 1: /usr/sbin/acfg_tool: not found
qcawificfg80211: enable radio wifi0
/etc/init.d/network: cp: omitting directory '/cfg/default/internal'
[   45.484107] wlan: [3591:I:ANY] wlan_scan_update_channel_list: 1107: num_chan: 13
[   45.484346] wlan: [3591:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 979: freq=58
[   45.491174] wlan: [3591:I:ANY] wlan_scan_update_channel_list: 1107: num_chan: 13
[   45.498780] wlan: [3591:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 979: freq=58
[   45.506181] wlan: [3591:I:ANY] number of channels: 2G = 0 5G = 13
/etc/init.d/network: Enable ol_stats by default for Lithium platforms
[   45.811394] wlan: [3735:I:ANY] wlan_cfg80211_set_hwaddr: 5537: wlan_cfg80211_set_hwaddr :8c:de:f9:ad:9d:f6 ret: 0
[   45.844571] wlan: [3749:I:ANY] ol_ath_set_config_param: 1493: set TXBF_SND_PERIOD: value 100 wmi_status 0
[   45.946986] wlan: [0:I:ANY] ol_ath_set_config_param: 2203: Disconnect_timeout value: 10
[   45.989931] wlan: [0:I:ANY] ol_ath_set_config_param: 2209: Reconfiguration_timeout value:60
/etc/init.d/network: cat: can't open '/lib/wifi/wifi_nss_hk_olnum': No such file or directory
/etc/init.d/network: sh: 3: unknown operand
number of vifs: cfg023579
[   46.190888] ipaccount: ifname [wifi0] event[13]
[   46.191096] ipaccount: ifname [wifi0] event[1]
/etc/init.d/network: cfg80211: ifname: wl0 mode: __ap cfgphy: phy0
/etc/rc.d/S51key_services_boot_check: @@@@@@ RA69 key_service_check skip wireless!
Mon Apr  1 21:38:49 CST 2024 boot_check[2919]: WARNING: no netwo[   46.315882] wlan: [3989:I:ANY] wlan_cfg80211_add_virtual_intf: 306: proprietary mode 6 for interface: wl0 : clone params: 0x00000001
[   46.316676] wlan: [3989:I:ANY] osifp_create_wlan_vap: 10193: VDEV Create 8c:de:f9:ad:9d:f6
[   46.328848] wlan: [3989:E:CMN_MLME] mlme_vdev_ext_obj_create: 1327:  VDEV MLME obj is creation
[   46.336954] wlan: [3989:I:ANY] wlan_vap_create: 1548: enter. devhandle=0xffffffc0164c0880, opmode=IEEE80211_M_HOSTAP, flags=0x1
[   46.336954]
[   46.345869] wlan: [3989:I:ANY] ol_ath_vap_set_param: 1107: Setting SGI value: 1
[   46.358716] wlan: [3989:I:ANY] ol_ath_vap_set_param: 2097: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1
[   46.365693] wlan: [3989:I:ANY] ol_ath_vap_set_param: 2107: he_bf_cap=0x7b
[   46.379297] wlan: [3989:I:ANY] ol_ath_vap_set_param: 2122: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged
[   46.386268] wlan: [3989:I:ANY] MBO Initialized
[   46.400242] wlan: [3989:I:ANY] OCE Initialized
[   46.404577] wlan: [3989:I:ANY] osif_nss_ol_vap_create: 1289: NSS wifi offload VAP create IF 30 nss_id -1
[   46.409011] wlan: [3989:I:ANY] NSS radio_if 28
[   46.418727] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1041: VDEV configuration success: 0
[   46.422983] wlan: [3989:I:ANY] osif_nss_ol_vap_create: 1397: vap create ffffffc011e98880 : if_num 30
[   46.431249] wlan: [3989:I:ANY] wlan_vap_create: 1582: exit
[   46.440620] wlan: [3989:E:ANY] SA disabled
[   46.446117] wlan: [3989:E:ANY] SA disabled
[   46.450072] wlan: [3989:I:ANY] osif_create_vap_complete: 10388: TX Checksum:1|SG:1|TSO:1|LRO:0
[   46.454137] wlan: [3989:I:ANY] WLAN-NSS: VAP NSS ops initialized
[   46.462903] ipaccount: ifname [wl0] event[16]
[   46.469537] ipaccount: ifname [wl0] event[5]
[   46.473372] wlan: [3989:I:ANY] VAP device wl0 created osifp: (ffffffc011e98880) os_if: (ffffffc010478000)
rk device eth0 available, current system /dev/
/etc/rc.d/S51key_services_boot_check: gzip: messages: No such file or directory
/etc/rc.d/S51key_services_boot_check: Trying to save syslog to crash...
/etc/rc.d/S51key_services_boot_check: can not open "messages.gz" for reading
/etc/rc.d/S51key_services_boot_check: target mtd /dev/mtd10
/etc/rc.d/S51key_services_boot_check: MTD Type: 4
/etc/rc.d/S51key_services_boot_check: MTD total size: 80000 bytes
/etc/rc.d/S51key_services_boot_check: MTD erase size: 20000 bytes
/etc/rc.d/S51key_services_boot_check: Beging Eraseing Block 0x400f28
/etc/rc.d/S51key_services_boot_check: End...
Mon Apr  1 21:38:50 CST 2024 boot_check[2919]: @@@@@@@@RA69
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAAA
S - OEM_IMAGE_VERSION_STRING=xiaoyang-gv
S - Boot Config, 0x000002e5
B -       201 - PBL, Start
B -      2735 - bootable_media_detect_entry, Start
B -      3441 - bootable_media_detect_success, Start
B -      3445 - elf_loader_entry, Start
B -      6107 - auth_hash_seg_entry, Start
B -      6349 - auth_hash_seg_exit, Start
B -     68433 - elf_segs_hash_verify_entry, Start
B -    131133 - PBL, End
B -    219356 - SBL1, Start
B -    300333 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    310307 - pm_device_init, Start
B -    494191 - PM_SET_VAL:Skip
D -    181627 - pm_device_init, Delta
B -    496448 - pm_driver_init, Start
D -      5307 - pm_driver_init, Delta
B -    502853 - clock_init, Start
D -      2135 - clock_init, Delta
B -    506910 - boot_flash_init, Start
D -     11895 - boot_flash_init, Delta
B -    522587 - boot_config_data_table_init, Start
D -      3202 - boot_config_data_table_init, Delta - (575 Bytes)
B -    530090 - Boot Setting :  0x00000600
B -    534024 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16
B -    540978 - sbl1_ddr_set_params, Start
B -    544791 - CPR configuration: 0x300
B -    548268 - cpr_init, Start
B -    551043 - Rail:0 Mode: 5 Voltage: 808000
B -    556198 - CL CPR settled at 760000mV
B -    559034 - Rail:1 Mode: 5 Voltage: 880000
B -    563213 - Rail:1 Mode: 7 Voltage: 912000
D -     16470 - cpr_init, Delta
B -    570106 - Pre_DDR_clock_init, Start
B -    574132 - Pre_DDR_clock_init, End
B -    577517 - DDR Type : PCDDR3
B -    583129 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    587979 - DDR: Start of HAL DDR Boot Training
B -    592706 - DDR: End of HAL DDR Boot Training
B -    598379 - DDR: Checksum to be stored on flash is -822398634
B -    608810 - Image Load, Start
D -    224053 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -    832924 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    840610 - Image Load, Start
D -     10706 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -    851407 - Image Load, Start
D -     25254 - RPM Image Loaded, Delta - (105964 Bytes)
B -    876722 - Image Load, Start
D -     96716 - APPSBL Image Loaded, Delta - (590292 Bytes)
B -    973590 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    979385 - USB D+ check, Start
D -        30 - USB D+ check, Delta
B -    985790 - SBL1, End
D -    768722 - SBL1, Delta
S - Flash Throughput, 6749 KB/s  (2096771 Bytes,  310637 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz

ca972008

应该是可以，7981的有通用方案，

本拉登他祖宗

ca972008 发表于 2025-8-13 15:22
应该是可以，7981的有通用方案，

能具体说说吗？或者给个参考链接谢谢

ca972008

https://www.cnblogs.com/p123/p/18046679

zero88

中断，是原厂uboot下面的，你刷了第三方的不敢说还能不能中断，但是你说你没刷机
图片中这个是原厂系统下面安装的？
鄙人不才。只是提出疑问哈

本拉登他祖宗

ca972008 发表于 2025-8-13 16:01
https://www.cnblogs.com/p123/p/18046679

感谢分享，但是我看了是关于联发科 SoC 救砖的，但是红米AX6不是联发科 SoC

zero88

ART分区坏了，救砖吧，可参考https://www.bilibili.com/opus/680152219395293188

为爱绝恋

5g模块挂了

oceanmax

为爱绝恋 发表于 2025-8-13 16:22
5g模块挂了

我的好像也是这样 ，刷过后5G信号特别微弱，刷回去也不行了，还能修好吗

xzzzq564

不知道啊

ca972008

这个机器论坛 应该有编程器固件，直接上编程器，一步到位，

不过如果是操作小白就算了，容易彻底报废，可以闲鱼摇人
路由器救砖，刷机，路由器硬改，硬件改造，增加闪存，换内存等，_闲鱼

本拉登他祖宗

zero88 发表于 2025-8-13 16:15
ART分区坏了，救砖吧，可参考https://www.bilibili.com/opus/680152219395293188

我按照了参考教程，但日志里还是中断进程被关闭状态bootwait is off, bootdelay=5，看来只能找人上编程器了