求DS218j的群晖DSM6.2.3-25426

li2858

我刚弄了一个黑群ds218j（设备是星际比特，蜂鸟h1），用国际账号洗白码洗白了，现在有种说法6.2.3的系统说可以qc，我想试一下，但是我现在缺6.2.3-25426的系统，在网上不好找，官网已经没有链接了，找找有没有链接可以下到的。

或者有没有大神们备份过6.2.3的全部系统（我当时就很想做这个事，没做成），我找找。

附上刷机的TTL日志，给大家个参考

1. U-Boot SPL 2018.01 (Feb 10 2021 - 21:56:21)
   
2. High speed PHY - Version: 2.0
   
3. Detected Device ID 6828
   
4. board SerDes lanes topology details:
   
5. | Lane #  | Speed |  Type       |
   
6. --------------------------------
   
7. |   0    |  5   |  PCIe0       |
   
8. |   1    |  3   |  SATA0       |
   
9. |   2    |  3   |  SATA1       |
   
10. |   3    |  5   |  USB3 HOST1  |
    
11. |   4    |  5   |  USB3 HOST0  |
    
12. |   5    |  0   |  SGMII2      |
    
13. --------------------------------
    
14. PCIe, Idx 0: detected no link
    
15. High speed PHY - Ended Successfully
    
16. DDR3 Training Sequence - Ver TIP-1.29.0
    
17. DDR3 Training Sequence - Switching XBAR Window to FastPath Window
    
18. DDR3 Training Sequence - Ended Successfully
    
19. Trying to boot from SPI
    
20. 
    
21. 
    
22. U-Boot 2018.01 (Feb 10 2021 - 21:56:21 +0800)
    
23. 
    
24. SoC:   MV88F6828-A0 at 1600 MHz
    
25. DRAM:  2 GiB (800 MHz, 32-bit, ECC not enabled)
    
26. NAND:  Ready timeout!!!
    
27. There is no chip on cs 0!
    
28. failed to scan nand at cs 0
    
29. 0 MiB
    
30. MMC:
    
31. SF: Detected mx25l12805 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
    
32. Model: ipfsbit h1
    
33. Board: ipfsbit h1
    
34. SCSI:  SATA link 0 timeout.
    
35. AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
    
36. Net:   eth1: ethernet@70000
    
37. Hit any key to stop autoboot:  0
    
38. =>
    
39. =>
    
40. =>
    
41. => dhcp
    
42. ethernet@70000 Waiting for PHY auto negotiation to complete....... done
    
43. BOOTP broadcast 1
    
44. BOOTP broadcast 2
    
45. BOOTP broadcast 3
    
46. BOOTP broadcast 4
    
47. DHCP client bound to address 192.168.5.70 (3883 ms)
    
48. => setenv serverip 192.168.5.186
    
49. => bubt full.bin spi tftp
    
50. Burning U-BOOT image "full.bin" from "tftp" to "spi"
    
51. Using ethernet@70000 device
    
52. TFTP from server 192.168.5.186; our IP address is 192.168.5.70
    
53. Filename 'full.bin'.
    
54. Load address: 0x800000
    
55. Loading: ##################################################  16 MiB
    
56.          1 MiB/s
    
57. done
    
58. Bytes transferred = 16777216 (1000000 hex)
    
59. Image checksum...OK!
    
60. SF: Detected mx25l12805 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
    
61. Erasing 16842752 bytes (257 blocks) at offset 0 ...Done!
    
62. Writing 16777216 bytes from 0x800000 to offset 0 ...Done!
    
63. =>
    
64. => reset
    
65. resetting ...
    
66. 
    
67. U-Boot SPL 2018.01 (Feb 10 2021 - 21:56:21)
    
68. High speed PHY - Version: 2.0
    
69. Detected Device ID 6828
    
70. board SerDes lanes topology details:
    
71. | Lane #  | Speed |  Type       |
    
72. --------------------------------
    
73. |   0    |  5   |  PCIe0       |
    
74. |   1    |  3   |  SATA0       |
    
75. |   2    |  3   |  SATA1       |
    
76. |   3    |  5   |  USB3 HOST1  |
    
77. |   4    |  5   |  USB3 HOST0  |
    
78. |   5    |  0   |  SGMII2      |
    
79. --------------------------------
    
80. PCIe, Idx 0: detected no link
    
81. High speed PHY - Ended Successfully
    
82. DDR3 Training Sequence - Ver TIP-1.29.0
    
83. DDR3 Training Sequence - Switching XBAR Window to FastPath Window
    
84. DDR3 Training Sequence - Ended Successfully
    
85. Trying to boot from SPI
    
86. 
    
87. 
    
88. U-Boot 2018.01 (Feb 10 2021 - 21:56:21 +0800)
    
89. 
    
90. SoC:   MV88F6828-A0 at 1600 MHz
    
91. DRAM:  2 GiB (800 MHz, 32-bit, ECC not enabled)
    
92. NAND:  Ready timeout!!!
    
93. There is no chip on cs 0!
    
94. failed to scan nand at cs 0
    
95. 0 MiB
    
96. MMC:
    
97. SF: Detected mx25l12805 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
    
98. Model: ipfsbit h1
    
99. Board: ipfsbit h1
    
100. SCSI:  SATA link 0 timeout.
     
101. AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
     
102. Net:   eth1: ethernet@70000
     
103. Hit any key to stop autoboot:  0
     
104. SF: Detected mx25l12805 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
     
105. device 0 offset 0x8f0000, size 0x2d0000
     
106. SF: 2949120 bytes @ 0x8f0000 Read: OK
     
107. device 0 offset 0xbc0000, size 0x410000
     
108. SF: 4259840 bytes @ 0xbc0000 Read: OK
     
109. device 0 offset 0x200000, size 0x10000
     
110. SF: 65536 bytes @ 0x200000 Read: OK
     
111. ## Booting kernel from Legacy Image at 02000000 ...
     
112.    Image Name:   Linux-3.10.105
     
113.    Created:      2020-05-11  20:43:07 UTC
     
114.    Image Type:   ARM Linux Kernel Image (uncompressed)
     
115.    Data Size:    2565112 Bytes = 2.4 MiB
     
116.    Load Address: 00008000
     
117.    Entry Point:  00008000
     
118.    Verifying Checksum ... OK
     
119. ## Loading init Ramdisk from Legacy Image at 03000000 ...
     
120.    Image Name:   synology_armada38x_ds218j 25426
     
121.    Created:      2020-05-11  22:15:14 UTC
     
122.    Image Type:   ARM Linux RAMDisk Image (uncompressed)
     
123.    Data Size:    3498016 Bytes = 3.3 MiB
     
124.    Load Address: 08000000
     
125.    Entry Point:  08000000
     
126.    Verifying Checksum ... OK
     
127. ## Flattened Device Tree blob at 01000000
     
128.    Booting using the fdt blob at 0x1000000
     
129.    Loading Kernel Image ... OK
     
130.    Loading Ramdisk to 0fca9000, end 0ffff020 ... OK
     
131.    Loading Device Tree to 0fca2000, end 0fca8a67 ... OK
     
132. MMC Device 0 not found
     
133. 
     
134. Starting kernel ...
     
135. 
     
136. Uncompressing Linux... done, booting the kernel.
     
137. [ 0.000000] Booting Linux on physical CPU 0x0
     
138. [ 0.000000] Initializing cgroup subsys cpuset
     
139. [ 0.000000] Initializing cgroup subsys cpu
     
140. [ 0.000000] Initializing cgroup subsys cpuacct
     
141. [ 0.000000] Linux version 3.10.105 (root@build4) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #25426 SMP Tue May 12 04:42:24 CST 2020
     
142. [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
     
143. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
     
144. [ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Synology DS218j
     
145. [ 0.000000] Truncating RAM at 00000000-7fffffff to -706fffff (vmalloc region overlap).
     
146. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
     
147. [ 0.000000] PERCPU: Embedded 7 pages/cpu @814f1000 s7168 r8192 d13312 u32768
     
148. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 456946
     
149. [ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x3000000 root=/dev/md0 rw syno_hw_version=DS218j syno_hdd_powerup_seq=2 ihd_num=2 netif_num=1 syno_hdd_enable=15,16 flash_size=8
     
150. [ 0.000000] Synology Hardware Version: DS218j-j
     
151. [ 0.000000] Power on seq num: 2
     
152. [ 0.000000] Internal HD num: 2
     
153. [ 0.000000] Internal netif num: 1
     
154. [ 0.000000] SYNO GPIO hdd enable pin: 15 16
     
155. [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
     
156. [ 0.000000] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
     
157. [ 0.000000] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
     
158. [ 0.000000] allocated 3684352 bytes of page_cgroup
     
159. [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
     
160. [ 0.000000] Memory: 1799MB = 1799MB total
     
161. [ 0.000000] Memory: 1812056k/1812056k available, 30120k reserved, 0K highmem
     
162. [ 0.000000] Virtual kernel memory layout:
     
163. [ 0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
     
164. [ 0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
     
165. [ 0.000000]     vmalloc : 0xf0800000 - 0xfff00000   ( 247 MB)
     
166. [ 0.000000]     lowmem  : 0x80000000 - 0xf0700000   (1799 MB)
     
167. [ 0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
     
168. [ 0.000000]       .text : 0x80008000 - 0x805fb18c   (6093 kB)
     
169. [ 0.000000]       .init : 0x805fc000 - 0x80635c00   ( 231 kB)
     
170. [ 0.000000]       .data : 0x80636000 - 0x8066cbc0   ( 219 kB)
     
171. [ 0.000000]        .bss : 0x8066cbc0 - 0x806d2d84   ( 409 kB)
     
172. [ 0.000000] Hierarchical RCU implementation.
     
173. [ 0.000000] NR_IRQS:16 nr_irqs:16 16
     
174. [ 0.000000]
     
175. [ 0.000000]   LSP version: linux-3.10.70-2015_T1.1p7
     
176. [ 0.000000]
     
177. [ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
     
178. [ 0.000000] L310 cache controller enabled
     
179. [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B
     
180. [ 0.000388] Calibrating delay loop... 3188.32 BogoMIPS (lpj=15941632)
     
181. [ 0.060026] pid_max: default: 32768 minimum: 301
     
182. [ 0.060070] Security Framework initialized
     
183. [ 0.060080] AppArmor: AppArmor initialized
     
184. [ 0.060096] Mount-cache hash table entries: 512
     
185. [ 0.060395] Initializing cgroup subsys memory
     
186. [ 0.060409] Disabling memory control group subsystem
     
187. [ 0.060412] Initializing cgroup subsys devices
     
188. [ 0.060415] Initializing cgroup subsys freezer
     
189. [ 0.060418] Initializing cgroup subsys blkio
     
190. [ 0.060440] CPU: Testing write buffer coherency: ok
     
191. [ 0.060541] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
     
192. [ 0.060572] Setting up static identity map for 0x8047d180 - 0x8047d1d8
     
193. [ 0.060690] mvebu-pmsu: Initializing Power Management Service Unit
     
194. [ 0.060719] Initializing CPU Reset module
     
195. [ 0.061290] CPU1: Booted secondary processor
     
196. [ 0.120561] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
     
197. [ 0.120613] Brought up 2 CPUs
     
198. [ 0.120621] SMP: Total of 2 processors activated (6376.65 BogoMIPS).
     
199. [ 0.120624] CPU: All CPU(s) started in SVC mode.
     
200. [ 0.120877] devtmpfs: initialized
     
201. [ 0.122913] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4
     
202. [ 0.123076] xor: measuring software checksum speed
     
203. [ 0.220552]    arm4regs  :  2841.600 MB/sec
     
204. [ 0.320552]    8regs     :  1958.400 MB/sec
     
205. [ 0.420551]    32regs    :  1992.400 MB/sec
     
206. [ 0.420554] xor: using function: arm4regs (2841.600 MB/sec)
     
207. [ 0.420559] pinctrl core: initialized pinctrl subsystem
     
208. [ 0.420803] regulator-dummy: no parameters
     
209. [ 0.420941] NET: Registered protocol family 16
     
210. [ 0.421432] DMA: preallocated 256 KiB pool for atomic coherent allocations
     
211. [ 0.423272] irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated
     
212. [ 0.423575] irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated
     
213. [ 0.425797] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
     
214. [ 0.425801] hw-breakpoint: maximum watchpoint size is 4 bytes.
     
215. [ 0.431994] bio: create slab <bio-0> at 0
     
216. [ 0.600688] raid6: int32x1  gen()   239 MB/s
     
217. [ 0.770657] raid6: int32x1  xor()   190 MB/s
     
218. [ 0.940695] raid6: int32x2  gen()   329 MB/s
     
219. [ 1.110645] raid6: int32x2  xor()   222 MB/s
     
220. [ 1.280668] raid6: int32x4  gen()   330 MB/s
     
221. [ 1.450561] raid6: int32x4  xor()   234 MB/s
     
222. [ 1.620697] raid6: int32x8  gen()   364 MB/s
     
223. [ 1.790633] raid6: int32x8  xor()   232 MB/s
     
224. [ 1.790636] raid6: using algorithm int32x8 gen() (364 MB/s)
     
225. [ 1.790639] raid6: .... xor() 232 MB/s, rmw enabled
     
226. [ 1.790641] raid6: using intx1 recovery algorithm
     
227. [ 1.790788] mvebu-pcie pcie-controller.3: PCIe0.0: link down
     
228. [ 1.790806] mvebu-pcie pcie-controller.3: PCIe1.0: link down
     
229. [ 1.790915] mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00
     
230. [ 1.790923] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
     
231. [ 1.790928] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
     
232. [ 1.790933] pci_bus 0000:00: root bus resource [bus 00-ff]
     
233. [ 1.791152] PCI: bus0: Fast back to back transfers disabled
     
234. [ 1.791158] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
     
235. [ 1.791164] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
     
236. [ 1.791240] PCI: bus1: Fast back to back transfers enabled
     
237. [ 1.791322] PCI: bus2: Fast back to back transfers enabled
     
238. [ 1.791348] pci 0000:00:01.0: PCI bridge to [bus 01]
     
239. [ 1.791355] pci 0000:00:02.0: PCI bridge to [bus 02]
     
240. [ 1.791362] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
     
241. [ 1.791367] PCI: enabling device 0000:00:02.0 (0140 -> 0143)
     
242. [ 1.791833] SCSI subsystem initialized
     
243. [ 1.792831] Switching to clocksource armada_370_xp_clocksource
     
244. [ 1.792999] AppArmor: AppArmor Filesystem Enabled
     
245. [ 1.793945] NET: Registered protocol family 2
     
246. [ 1.794247] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
     
247. [ 1.794367] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
     
248. [ 1.794483] TCP: Hash tables configured (established 16384 bind 16384)
     
249. [ 1.794511] TCP: reno registered
     
250. [ 1.794517] UDP hash table entries: 1024 (order: 3, 32768 bytes)
     
251. [ 1.794550] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
     
252. [ 1.794657] NET: Registered protocol family 1
     
253. [ 1.794803] RPC: Registered named UNIX socket transport module.
     
254. [ 1.794808] RPC: Registered udp transport module.
     
255. [ 1.794811] RPC: Registered tcp transport module.
     
256. [ 1.794814] RPC: Registered tcp NFSv4.1 backchannel transport module.
     
257. [ 1.794905] Trying to unpack rootfs image as initramfs...
     
258. [ 2.802372] Freeing initrd memory: 3416K (8fca9000 - 8ffff000)
     
259. [ 2.802566] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
     
260. [ 2.803987] Initialise module verification
     
261. [ 2.804022] audit: initializing netlink socket (disabled)
     
262. [ 2.804049] type=2000 audit(2.800:1): initialized
     
263. [ 2.805204] VFS: Disk quotas dquot_6.5.2
     
264. [ 2.805252] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
     
265. [ 2.805518] NFS: Registering the id_resolver key type
     
266. [ 2.805533] Key type id_resolver registered
     
267. [ 2.805536] Key type id_legacy registered
     
268. [ 2.805554] msgmni has been set to 3545
     
269. [ 2.806084] async_tx: api initialized (async)
     
270. [ 2.806090] Key type asymmetric registered
     
271. [ 2.806093] Asymmetric key parser 'x509' registered
     
272. [ 2.806263] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
     
273. [ 2.806269] io scheduler noop registered
     
274. [ 2.806283] io scheduler c购物 registered (default)
     
275. [ 2.807038] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
     
276. [ 2.807502] mv_xor f1060800.xor: Marvell shared XOR driver
     
277. [ 2.843150] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
     
278. [ 2.873138] mv_xor f1060800.xor: freeing 1 in use descriptors!
     
279. [ 2.873147] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
     
280. [ 2.874147] mv_xor f1060900.xor: Marvell shared XOR driver
     
281. [ 2.913113] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
     
282. [ 2.943134] mv_xor f1060900.xor: freeing 1 in use descriptors!
     
283. [ 2.943144] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
     
284. [ 2.944569] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
     
285. [ 2.966300] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A
     
286. [ 3.787282] console [ttyS0] enabled
     
287. [ 3.799537] brd: module loaded
     
288. [ 3.802601] Loading iSCSI transport class v2.0-870.
     
289. [ 3.809788] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
     
290. [ 3.818617] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
     
291. [ 3.828782] scsi0 : ahci_mv_platform
     
292. [ 3.832838] scsi1 : ahci_mv_platform
     
293. [ 3.836880] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58
     
294. [ 3.844836] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58
     
295. [ 7.192857] ata1: SATA link down (SStatus 0 SControl 300)
     
296. [ 7.198269] ata1: No present pin info for SATA link down event
     
297. [ 7.204134] Delay 5 seconds to wait for disk 2 ready.
     
298. [15.522855] ata2: SATA link down (SStatus 0 SControl 300)
     
299. [15.528265] ata2: No present pin info for SATA link down event
     
300. [15.536950] m25p80 spi1.0: found mx25l12805d, expected mx25l6405d
     
301. [15.543077] m25p80 spi1.0: mx25l12805d (16384 Kbytes)
     
302. [15.548149] Searching for RedBoot partition table in spi1.0 at offset 0xff0000
     
303. [15.649888] 6 RedBoot partitions found on MTD device spi1.0
     
304. [15.655482] Creating 6 MTD partitions on "spi1.0":
     
305. [15.660284] 0x000000800000-0x0000008f0000 : "RedBoot"
     
306. [15.666361] 0x0000008f0000-0x000000bc0000 : "zImage"
     
307. [15.672458] 0x000000bc0000-0x000000fd0000 : "rd.gz"
     
308. [15.678371] 0x000000fd0000-0x000000fe0000 : "vendor"
     
309. [15.683604] vender Mac0 address : 00:11:32:be:f4:c0
     
310. [15.688493] vender Mac1 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
     
311. [15.694348] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
     
312. [15.700192] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
     
313. [15.706056] serial number='184AQ2N142000'
     
314. [15.710848] 0x000000fe0000-0x000000ff0000 : "RedBoot Config"
     
315. [15.717717] 0x000000ff0000-0x000001000000 : "FIS directory"
     
316. [15.727041] SoC: model = 0x6828, revision = 0x4
     
317. [15.731637] mvirtual**cVirtBase = 0xf0c00000, pncTcamSize = 1024
     
318. [15.737152]   o 3 Giga ports supported
     
319. [15.740906]   o SKB recycle supported for SWF (Disabled)
     
320. [15.746244]   o NETA acceleration mode 4
     
321. [15.750172]   o BM supported for CPU: 4 BM pools
     
322. [15.754801]   o PnC supported (Enabled)
     
323. [15.758644]   o RX Queue support: 8 Queues * 512 Descriptors
     
324. [15.764317]   o TX Queue support: 8 Queues * 1024 Descriptors
     
325. [15.770073]   o GSO supported
     
326. [15.773047]   o GRO supported
     
327. [15.776017]   o Receive checksum offload supported
     
328. [15.780816]   o Transmit checksum offload supported
     
329. [15.785704]   o Driver ERROR statistics enabled
     
330. [15.790241]   o Driver INFO statistics enabled
     
331. [15.794694]   o Driver DEBUG statistics enabled
     
332. [15.799232]
     
333. [15.801594] port #0: is_sgmii=0, is_rgmii=1, phy_addr=0
     
334. [15.806864]   o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800
     
335. [15.815165]
     
336. [15.816657]   o Port 0 is connected to Linux netdevice
     
337. [15.825646]     o eth0, ifindex = 2, GbE port = 0
     
338. [15.830375]     o eth0, phy chipid = 1410dd0, Support WOL = 32
     
339. [15.839677]  giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform)
     
340. [15.845788]
     
341. [15.847716] libphy: orion_mdio_bus: probed
     
342. [15.854370] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
     
343. [15.913025] i2c /dev entries driver
     
344. [15.927091] armada_thermal f10e4078.thermal: Overheat threshold between 92..107
     
345. [15.934956] md: linear personality registered for level -1
     
346. [15.940455] md: raid0 personality registered for level 0
     
347. [15.945791] md: raid1 personality registered for level 1
     
348. [15.951115] md: raid10 personality registered for level 10
     
349. [15.956812] md: raid6 personality registered for level 6
     
350. [15.962137] md: raid5 personality registered for level 5
     
351. [15.967469] md: raid4 personality registered for level 4
     
352. [15.973006] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
     
353. [15.981465] cpuidle: using governor ladder
     
354. [15.985807] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2
     
355. [15.995150] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0)
     
356. [16.003622] mvCesaInit: channels=2, session=640, queue=256
     
357. [16.018600] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode
     
358. [16.027980] cesadev_init(8061aaf4)
     
359. [16.032034] TCP: cubic registered
     
360. [16.035373] NET: Registered protocol family 17
     
361. [16.039870] Key type dns_resolver registered
     
362. [16.044218] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
     
363. [16.051919] Registering suspend init for this board failed
     
364. [16.059813] Loading module verification blacklist certificates
     
365. [16.065694] Loading module verification certificates
     
366. [16.070717] MODSIGN: Loaded cert 'Synology SDG kernel module signing key: 7bd0b0d6bcd31651c22ce3978bdc8c8bdc417329'
     
367. [16.085501] MODSIGN: Loaded cert 'Synology Root Certification Authority: f2c075361f168425f8b5ef31b796406c3aab2089'
     
368. [16.095910] MODSIGN: Loaded cert 'Synology Kernel Module Signing Certification Authority: 600839b5d127e0e11d817a31f0575d323a7c0e28'
     
369. [16.107787] MODSIGN: Loaded cert 'Synology kernel module signing key: 4646ce54489669338118a3b1286da156ac366fa5'
     
370. [16.117912] registered taskstats version 1
     
371. [16.122047] regulator-dummy: disabling
     
372. [16.126093] Freeing unused kernel memory: 228K (805fc000 - 80635000)
     
373. START /linuxrc.syno
     
374. Insert basic USB modules...
     
375. :: Loading module usb-common ... [  OK  ]
     
376. :: Loading module usbcore[16.270306] usbcore: registered new interface driver usbfs
     
377. [16.278437] usbcore: registered new interface driver hub
     
378. [16.286265] usbcore: registered new device driver usb
     
379. ... [  OK  ]
     
380. :: Loading module ehci-hcd[16.330073] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
381. ... [  OK  ]
     
382. :: Loading module xhci-hcd[16.368398] xhci-hcd f10f0000.usb3: USB2 Vbus gpio 58
     
383. [16.373562] xhci-hcd f10f0000.usb3: power control enabled
     
384. [16.378981] xhci-hcd f10f0000.usb3: xHCI Host Controller
     
385. [16.384336] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1
     
386. [16.391982] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
     
387. [16.398345] hub 1-0:1.0: USB hub found
     
388. [16.402122] hub 1-0:1.0: 1 port detected
     
389. [16.406200] xhci-hcd f10f0000.usb3: USB3 Vbus gpio 58
     
390. [16.411269] xhci-hcd f10f0000.usb3: power control enabled
     
391. [16.416714] xhci-hcd f10f0000.usb3: xHCI Host Controller
     
392. [16.422055] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
     
393. [16.431875] hub 2-0:1.0: USB hub found
     
394. [16.435697] hub 2-0:1.0: 1 port detected
     
395. [16.439777] xhci-hcd f10f8000.usb3: USB2 Vbus gpio 59
     
396. [16.444875] xhci-hcd f10f8000.usb3: power control enabled
     
397. [16.450294] xhci-hcd f10f8000.usb3: xHCI Host Controller
     
398. [16.455655] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3
     
399. [16.463352] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
     
400. [16.471355] hub 3-0:1.0: USB hub found
     
401. [16.475186] hub 3-0:1.0: 1 port detected
     
402. [16.479230] xhci-hcd f10f8000.usb3: USB3 Vbus gpio 59
     
403. [16.484331] xhci-hcd f10f8000.usb3: power control enabled
     
404. [16.489749] xhci-hcd f10f8000.usb3: xHCI Host Controller
     
405. [16.495112] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
     
406. [16.504984] hub 4-0:1.0: USB hub found
     
407. [16.508764] hub 4-0:1.0: 1 port detected
     
408. ... [  OK  ]
     
409. :: Loading module ehci-orion[16.567671] ehci-orion: EHCI orion driver
     
410. [16.571832] orion-ehci f1058000.usb: failed to get Vbus gpio
     
411. [16.577534] orion-ehci f1058000.usb: USB2 Vbus gpio -1
     
412. [16.582685] orion-ehci f1058000.usb: power control disabled
     
413. [16.588274] orion-ehci f1058000.usb: EHCI Host Controller
     
414. [16.593697] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 5
     
415. [16.601332] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000
     
416. [16.622874] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
     
417. [16.629636] hub 5-0:1.0: USB hub found
     
418. [16.633445] hub 5-0:1.0: 1 port detected
     
419. ... [  OK  ]
     
420. insmod: can't insert '/lib/modules/etxhci-hcd.ko': No such file or directory
     
421. Insert net driver(Mindspeed only).[16.684746] ds218j_synobios: module license 'Synology Inc.' taints kernel.
     
422. ..
     
423. [16.692748] Disabling lock debugging due to kernel taint
     
424. [16.699334] Synobios DS218j GPIO initialized
     
425. [16.703812] 2026-3-26 23:59:23 UTC
     
426. [16.707227] synobios: load, major number 201
     
427. [16.711509] Brand: Synology
     
428. [16.714333] Model: DS-218j
     
429. [16.717054] This is default settings: set group disks wakeup number to 1, spinup time deno 1
     
430. [16.725531] synobios cpu_arch proc entry initialized
     
431. [16.730506] synobios crypto_hw proc entry initialized
     
432. [16.735573] synobios syno_platform proc entry initialized
     
433. [16.741017] synobios ioctl TCGETS /dev/ttyS1 failed
     
434. [16.745909] synobios unable to set termios of /dev/ttyS1
     
435. Starting /usr/syno/bin/synocfgen...
     
436. /usr/syno/bin/synocfgen returns 0
     
437. [16.764020] synobios: unload
     
438. Exit on error [1] DISK NOT INSTALLED...
     
439. Thr Mar 26 23:59:23 UTC 2026
     
440. none /sys/kernel/debug debugfs rw,relatime 0 0
     
441. sys /sys sysfs rw,relatime 0 0
     
442. none /dev devtmpfs rw,relatime,size=906028k,nr_inodes=226507,mode=755 0 0
     
443. proc /proc proc rw,relatime 0 0
     
444. linuxrc.syno failed on 1
     
445. starting pid 863, tty '': '/etc/rc'
     
446. :: Starting /etc/rc
     
447. :: Mounting procfs ... [  OK  ]
     
448. :: Mounting tmpfs ... [  OK  ]
     
449. :: Mounting devtmpfs ... [  OK  ]
     
450. :: Mounting devpts ... [  OK  ]
     
451. :: Mounting sysfs ... [  OK  ]
     
452. mdadm: error opening /dev/md1: No such file or directory
     
453. rc: Use all internal disk as swap.
     
454. rc: No internal disk installed.
     
455. swapon: can't stat '/dev/md1': No such file or directory
     
456. :: Loading module fat ... [  OK  ]
     
457. :: Loading module vfat ... [  OK  ]
     
458. :: Loading module synobios[17.340009] Synobios DS218j GPIO initialized
     
459. [17.344537] 2026-3-26 23:59:24 UTC
     
460. [17.347952] synobios: load, major number 201
     
461. [17.352234] Brand: Synology
     
462. [17.355061] Model: DS-218j
     
463. [17.357782] This is default settings: set group disks wakeup number to 1, spinup time deno 1
     
464. [17.366260] synobios cpu_arch proc entry initialized
     
465. [17.371234] synobios crypto_hw proc entry initialized
     
466. [17.376303] synobios syno_platform proc entry initialized
     
467. [17.381742] synobios ioctl TCGETS /dev/ttyS1 failed
     
468. [17.386640] synobios unable to set termios of /dev/ttyS1
     
469. ... [  OK  ]
     
470. [17.526281] eth0: mac address changed
     
471. [17.581922] pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added
     
472. [17.589442] eth0: link up
     
473. [17.592135] eth0:
     
474. [17.593984] link up, full duplex
     
475. [17.597237] , speed
     
476. [17.599433] 1 Gbps
     
477. [17.601452] eth0: started
     
478. udhcpc (v1.16.1) started
     
479. eth0      Link encap:Ethernet  HWaddr 00:11:32:BE:F4:C0
     
480.           inet addr:169.254.193.151  Bcast:169.254.255.255  Mask:255.255.0.0
     
481.           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
     
482.           RX packets:2 errors:0 dropped:0 overruns:0 frame:0
     
483.           TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
     
484.           collisions:0 txqueuelen:1024
     
485.           RX bytes:120 (120.0 B)  TX bytes:890 (890.0 B)
     
486.           Interrupt:193
     
487. 
     
488. lo        Link encap:Local Loopback
     
489.           inet addr:127.0.0.1  Mask:255.0.0.0
     
490.           UP LOOPBACK RUNNING  MTU:65536  Metric:1
     
491.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
     
492.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
     
493.           collisions:0 txqueuelen:0
     
494.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
     
495. 
     
496. :: Starting syslogd ... [  OK  ]
     
497. /etc/rc: line 280: /usr/syno/bin/syno_pstore_collect: not found
     
498. :: Starting scemd
     
499. [24.946778] synobios write k to /dev/ttyS1 failed
     
500. :: Starting services in background
     
501. Starting findhostd in flash_rd...
     
502. Starting services in flash_rd...
     
503. Running /usr/syno/etc/rc.d/J01httpd.sh...
     
504. Starting httpd:80 in flash_rd...
     
505. Starting httpd:5000 in flash_rd...
     
506. Running /usr/syno/etc/rc.d/J03ssdpd.sh...
     
507. /usr/bin/minissdpd -i eth0
     
508. (15): upnp:rootdevice
     
509. (51): uuid:upnp_SynologyNAS-001132bef4c0::upnp:rootdevice
     
510. (58): Synology/synology_armada38x_ds218j/6.2-25426/192.168.5.253
     
511. (46): http://192.168.5.253:5000/description-eth0.xml
     
512. Connected.
     
513. done.
     
514. /usr/syno/bin/reg_ssdp_service 192.168.5.253 001132bef4c0 6.2-25426 synology_armada38x_ds218j eth0
     
515. Running /usr/syno/etc/rc.d/J04synoagentregisterd.sh...
     
516. Starting synoagentregisterd...
     
517. Running /usr/syno/etc/rc.d/J30DisableNCQ.sh...
     
518. cat: can't open '/sys/block/sd*/device//model': No such file or directory
     
519. Running /usr/syno/etc/rc.d/J80ADTFanControl.sh...
     
520. Running /usr/syno/etc/rc.d/J98nbnsd.sh...
     
521. Starting nbnsd...
     
522. Running /usr/syno/etc/rc.d/J99avahi.sh...
     
523. Starting Avahi mDNS/DNS-SD Daemon
     
524. cname_load_conf failed:/var/tmp/nginx/avahi-aliases.conf
     
525. :: Loading module usb-storage[25.318201] usbcore: registered new interface driver usb-storage
     
526. ... [  OK  ]
     
527. Excution Error
     
528. ============ Date ============
     
529. Thr Mar 26 23:59:32 UTC 2026
     
530. ========
     
531. Thu Mar 26 23:59:33 2026
     
532. 
     
533. DiskStation login: [39.401485] findhostd uses obsolete (PF_INET,SOCK_PACKET)
     
534. [  134.466972] open mtd (vendor), process=mantool
     
535. [  134.471447] close mtd (vendor), process=mantool
     
536. [  134.476074] open mtd (vendor), process=mantool
     
537. [  134.480856] close mtd (vendor), process=mantool
     
538. [  134.486023] open mtd (vendor), process=mantool
     
539. [  134.490482] close mtd (vendor), process=mantool
     
540. [  297.950546] ata1: device plugged sstatus 0x101
     
541. [  297.955037] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
     
542. [  297.962452] ata1: irq_stat 0x80000040, connection status changed
     
543. [  297.968490] ata1: SError: { PHYRdyChg CommWake DevExch }
     
544. [  297.973832] ata1: hard resetting link
     
545. [  298.922856] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
     
546. [  298.930641] ata1.00: ATA-9: SanDisk SSD U100 24GB, 10.52.01, max UDMA/133
     
547. [  298.937459] ata1.00: 46905264 sectors, multi 1: LBA48 NCQ (depth 31/32)
     
548. [  298.944093] ata1.00: SN:123563314992
     
549. [  298.948000] ata1.00: configured for UDMA/133
     
550. [  298.952282] ata1.00: Write Cache is enabled
     
551. [  298.956487] ata1: EH complete
     
552. [  298.959467] ata1.00: Find SSD disks. [SanDisk SSD U100 24GB]
     
553. [  298.965396] scsi 0:0:0:0: Direct-Access     SanDisk  SSD U100 24GB            10.5 PQ: 0 ANSI: 5
     
554. [  298.976753] sd 0:0:0:0: [sda] 46905264 512-byte logical blocks: (24.0 GB/22.3 GiB)
     
555. [  298.984645] sd 0:0:0:0: [sda] Write Protect is off
     
556. [  298.991197] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
     
557. [  299.007674]  sda: unknown partition table
     
558. [  299.012557] sd 0:0:0:0: [sda] Attached SCSI disk
     
559. 
     
560. DiskStation login:
     

复制代码

xdm2211

不是X86的很难搞啊

li2858

xdm2211 发表于 2026-3-28 06:51
不是X86的很难搞啊

所以我搜遍全网都没找到，我觉得应该有人备份过吧

li2858

找到了，有要的私信我吧