|
|
解压后需要用 7zip再解压一次。
论坛附件限制太小了，实属无奈
下面是官方的说明，由于时间关系未有翻译。希望英文好的有时间的朋友帮忙翻译。更详细内容请阅读里面的readme
Tomato Firmware
Readme
This firmware is provided as-is without any warranty. USE AT YOUR OWN RISK. I will NOT be responsible for damages that occur due to the use of this firmware.
About
Tomato is a small, lean, simple replacement firmware for Linksys' WRT54G/GL/GS, Buffalo WHR-G54S/WHR-HP-G54, and other Broadcom-based routers. It features a new easy to use GUI, a new bandwidth usage monitor, more advanced QOS and access restrictions, enables new wireless features such as WDS and wireless client modes, raises the limits on maximum connections for P2P, allows you to run your custom scripts or telnet/ssh in and do all sorts of things like re-program the SES/AOSS button, adds wireless site survey to see your wifi neighbors, and more.
Please consider donating if you like it. 
For more information about Tomato, please visit http://www.polarcloud.com/tomato/
Read Before Upgrading
The GUI relies heavily on JavaScript to generate the content and XMLHTTP (AJAX) to update it. Be careful if you need to use this from an older/minimal browser since it was not designed to downgrade gracefully. This has been tested only on Firefox v1/2, Opera v9 and IE v6/7. See below for information about browsers and graphs/SVG.
The GUI username is "admin" or "root" (username is required), ssh and telnet username is always "root", and the default password is "admin".
By default, the SES (AOSS, EZ-Setup) button is programmed to start a password-less telnet deamon at port 233 if held for 20+ seconds. If you run into a problem of not being able to login, you can use this to view or reset the password ("nvram get http_passwd" and "nvram set http_passwd=newpassword"). You can disable this behavior in Admin/Buttons.
If you're upgrading from DD-WRT v23 SP2+, be aware that you may get locked-out because of a change in DD-WRT's use of the nvram password variable. You have a few options: (1) Push the reset button to reset all the configuration after installing Tomato. (2) Use the SES button as described above. (3) Type "nvram get http_passwd" while running DD-WRT and write down the result - this will be your password after loading Tomato.
The firmware files:
WRT54G\code.bin is for Linksys WRT54G v1-4 and WRT54GL v1.
WRT54GS\code.bin is for Linksys WRT54GS v1-3.
WRT54GSv4\code.bin is for Linksys WRT54GS v4.
WRTSL54GS\code.bin is for Linksys WRTSL54GS (No USB support).
trx\code.trx is for the Buffalo WHR-G54S, WHR-HP-G54 and WZR-G54, and Asus WL-500G Premium (No USB support).
If you're just upgrading an existing Tomato firmware from the GUI, any of these files will work on all routers.
Installing on a stock Linksys router
Open the Linksys GUI in your browser. The default URL is http://192.168.1.1/.
Click the Administration tab, then Firmware Upgrade.
Select and upload the correct firmware for your router.
Wait for about 2 minutes while the firmware is uploaded & flashed.
Installing on a stock Buffalo router
WARNING: Be aware that Buffalo only has encrypted firmwares on their web site. You will not be able to revert the router's firmware back to Buffalo's without an unecrypted version of their firmware.
The following is for an initial install on a Buffalo router. If you're already using a third-party firmware or just upgrading a Tomato firmware, try uploading any of the .bin files from the GUI.
Push the reset button for a few seconds to reset the configuration.
Plug your computer directly to the router. This will not work over a wireless connection.
Set your computer's ethernet card settings to: IP=192.168.11.2, mask=255.255.255.0, gateway=192.168.11.1. In Windows, you can set this by going to Control Panel, Network Connections, right-click your ethernet card, click properties, then TCP/IP.
Make sure the red diagnostic light isn't lit, unplug the power cable, wait, then re-plug.
If you're using Windows, double-click on the whr_install.bat file or use the following command: tftp -i 192.168.11.1 put code.trx
If you're using another OS, start tftp with something like the following:
tftp 192.168.11.1
binary
put code.trx
You only have a 5 second window to do this, so if it doesn't work, unplug and try again.
After uploading, wait. It still needs about 2 minutes to flash the image.
Reset your computer's ethernet card settings back to use DHCP.
The default router address is 192.168.1.1. The CFE and future TFTP upgrades will also default to this address and will follow the settings entered in the GUI. |
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？立即注册
×
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
