703n ttl 刷机后一直重启 ，求助，换了很多固件

xcx***

703n ttl 刷机后一直重启 ，求助，换了很多固件。

邪恶***

http://pan.baidu.com/share/link?shareid=138250&uk=891727794

xcx***

也是一样的，会不会刷的过程有问题？https://www.right.com.cn/forum/f ... hread&tid=79618 我是按照这个刷的

xcx***

求助

henry***

看起來是刷壞了，建議在第32行的地方，用複製貼上的方法比較不會出錯，那邊關係到記憶體的位置。輸入錯，就會發生你的情況

xcx***

继续求助 ，会不会内存坏了？

744***

别一直刷，我以前也总是遇到这个问题。一天到晚的刷，flash反应不过来（我猜是这样吧）然后就是这样。我的解决办法是在easer和cp.b  的时候执行两遍，这样就好了。

xcx***

7440909 发表于 2012-11-16 22:32
别一直刷，我以前也总是遇到这个问题。一天到晚的刷，flash反应不过来（我猜是这样吧）然后就是这样。我的解 ...

谢谢，试试看！

xcx***

xcxc110 发表于 2012-11-17 00:10
谢谢，试试看！

还是一样的

xcx***

估计内存坏了 ，mtest 无法测试，换了64m的
变成
Starting kernel ...

[    0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Sat Oct 20 12:31:22 UTC 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61496k/65536k available (2209k kernel code, 4040k reserved, 412k data, 212k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.350000] bio: create slab <bio-0> at 0
[    0.360000] Switching to clocksource MIPS
[    0.360000] NET: Registered protocol family 2
[    0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.370000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.380000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.380000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.390000] TCP reno registered
[    0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] NET: Registered protocol family 1
[    0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.440000] msgmni has been set to 120
[    0.440000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.450000] io scheduler noop registered
[    0.450000] io scheduler deadline registered (default)
[    0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.480000] console [ttyATH0] enabled, bootconsole disabled
[    0.480000] console [ttyATH0] enabled, bootconsole disabled
[    0.490000] m25p80 spi0.0: found en25q32b, expected m25p80
[    0.500000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[    0.500000] 5 tp-link partitions found on MTD device spi0.0
[    0.510000] Creating 5 MTD partitions on "spi0.0":
[    0.510000] 0x000000000000-0x000000020000 : "u-boot"
[    0.520000] 0x000000020000-0x000000110000 : "kernel"
[    0.520000] 0x000000110000-0x0000003f0000 : "rootfs"
[    0.530000] mtd: partition "rootfs" set to be root filesystem
[    0.530000] split_squashfs: no squashfs found in "spi0.0"
[    0.540000] 0x0000003f0000-0x000000400000 : "art"
[    0.540000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.570000] ag71xx_mdio: probed
[    0.570000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.130000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.130000] TCP cubic registered
[    1.140000] NET: Registered protocol family 17
[    1.140000] Bridge firewalling registered
[    1.150000] 8021q: 802.1Q VLAN Support v1.8
[    2.160000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x2c0000
[    2.170000] jffs2_build_filesystem(): unlocking the mtd device... done.
[    2.170000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[    2.700000] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    2.710000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
[    2.720000] Freeing unused kernel memory: 212k freed
[    2.730000] Kernel panic - not syncing: No init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.

zhuj***

xcxc110 发表于 2012-11-18 15:31
估计内存坏了 ，mtest 无法测试，换了64m的
变成
Starting kernel ...

内存坏，根本不启动的。。。用ttl清空固件区，再重新刷固件吧

xcx***

zhujunsq 发表于 2012-11-18 16:02
内存坏，根本不启动的。。。用ttl清空固件区，再重新刷固件吧

ttl 如何清空固件区

zhuj***

tftp 0x80000000 fw.bin
erase 0x9f020000 +0x3c0000
cp.b 0x80000000 0x9f020000 0x3c0000

xcx***

zhujunsq 发表于 2012-11-18 19:19
tftp 0x80000000 fw.bin
erase 0x9f020000 +0x3c0000
cp.b 0x80000000 0x9f020000 0x3c0000

就是这么刷的