|
|
本帖最后由 200420154 于 2013-12-22 17:10 编辑
从MW300RV4之后的版本改用MT7620后，改路由的人貌似少了，不知道是MT7620不太好改。现在的新版本又回到原来的AR了，不过加了一个QCA。可惜目前op未作支持。
前几天48rmb买了一个MW305R+，硬改后尝试启动一下，当然网口跟无线都因为驱动问题没驱动。
U-Boot 1.1.4 (Build from LSDK-9.5.3.16 at Dec 19 2013 - 01:35:26)
ap143 - Honey Bee 1.1
DRAM: 64 MB
id read 0x10215
FLASH: Spansion S25FL032P
SIZE: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:0xc02200
Scorpion ---->S27 PHY*
S27 reg init
GMAC: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 4:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4:0x10
eth0 up
Honey Bee ----> MAC 1 S27 PHY*
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
GMAC: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 1:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2:0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3:0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3:0x10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x64c9a100
is_auto_upload_firmware=0
Hit any key to stop autoboot: 0
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.24 (lin@lin-laptop) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39130) ) #60 Sun Dec 22 16:58:28 CST 2013
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 rev 1
[ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR841N-v8 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61272k/65536k available (2199k kernel code, 4264k reserved, 593k data, 276k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] MIPS: machine is TP-LINK TL-WR841N/ND v8
[ 0.490000] bio: create slab <bio-0> at 0
[ 0.490000] Switching to clocksource MIPS
[ 0.500000] NET: Registered protocol family 2
[ 0.500000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.510000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.520000] TCP: Hash tables configured (established 512 bind 512)
[ 0.520000] TCP: reno registered
[ 0.520000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.530000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.540000] NET: Registered protocol family 1
[ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.570000] msgmni has been set to 119
[ 0.580000] io scheduler noop registered
[ 0.580000] io scheduler deadline registered (default)
[ 0.590000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
俽矈倐倐陙serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.620000] console [ttyS0] enabled, bootconsole disabled
[ 0.620000] console [ttyS0] enabled, bootconsole disabled
[ 0.630000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.640000] m25p80 spi0.0: found s25sl032p, expected m25p80
[ 0.650000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
[ 0.650000] 5 tp-link partitions found on MTD device spi0.0
[ 0.660000] Creating 5 MTD partitions on "spi0.0":
[ 0.660000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.670000] 0x000000020000-0x0000001196a8 : "kernel"
[ 0.680000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.690000] 0x0000001196a8-0x0000003f0000 : "rootfs"
[ 0.700000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.710000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.720000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.720000] 0x0000002d0000-0x0000003f0000 : "rootfs_data"
[ 0.730000] 0x0000003f0000-0x000000400000 : "art"
[ 0.740000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.760000] libphy: ag71xx_mdio: probed
[ 1.320000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=00000000, driver=Generic PHY]
[ 1.330000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.890000] ag71xx-mdio.1: unknown phy id '0000:0000'
[ 1.890000] TCP: cubic registered
[ 1.900000] NET: Registered protocol family 17
[ 1.900000] 8021q: 802.1Q VLAN Support v1.8
[ 1.910000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.920000] Freeing unused kernel memory: 276K (8031b000 - 80360000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 4.550000] usbcore: registered new interface driver usbfs
[ 4.560000] usbcore: registered new interface driver hub
[ 4.560000] usbcore: registered new device driver usb
[ 4.580000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.580000] ehci-platform: EHCI generic platform driver
[ 4.590000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
mount_root: jffs2 is ready
[ 7.020000] jffs2: notice: (313) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 13 of xref (0 dead, 2 orphan) found.
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 7.820000] NET: Registered protocol family 10
[ 7.830000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
[ 7.840000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.870000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[ 7.880000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 7.890000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.930000] xt_time: kernel timezone is -0000
[ 7.960000] cfg80211: Calling CRDA to update world regulatory domain
[ 7.960000] cfg80211: World regulatory domain updated:
[ 7.970000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.980000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.980000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.990000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.000000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 8.010000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 8.020000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 8.070000] PPP generic driver version 2.4.2
[ 8.090000] NET: Registered protocol family 24
[ 8.170000] cfg80211: Calling CRDA for country: US
[ 8.180000] ieee80211 phy0: Atheros AR9530 Rev:0 mem=0xb8100000, irq=47
[ 8.190000] cfg80211: Regulatory domain changed to country: US
[ 8.200000] cfg80211: DFS Master region FCC
[ 8.200000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.210000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 8.220000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
[ 8.230000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[ 8.230000] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[ 8.240000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
[ 8.250000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
[ 8.260000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
procd: - init complete -
[ 13.760000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.800000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 15.240000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 15.260000] device wlan0 entered promiscuous mode
[ 15.300000] br-lan: port 1(wlan0) entered forwarding state
[ 15.300000] br-lan: port 1(wlan0) entered forwarding state
[ 15.310000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 15.340000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 17.300000] br-lan: port 1(wlan0) entered forwarding state
目测op支持只是时间问题吧。
|
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡