小白又有新问题来请教了

gjs · 发表于 2014-3-9 01:08

有一台MW305R，换RAM和FLASH后，无法进入WEB设置页面，直接就进了固件升级界面，但这台机子和俺原来改的那台应该是不同的问题，这台未使用普通助焊剂，焊接也应该良好，接TTL用CRT看发现CRC校验失败，故直接进入了update。。。
问题1：Memory Testing ok是否能证明内存就没问题了？因为俺不知道这个TEST是否是全部的测试。。。
   2：7620是否使用了硬件CRC测试？要是的话就有可能还是不能排除RAN有问题，硬件CRC不需要依赖RAM或只需要极小的RAM吗？
   3：俺另外还有一台MW305R，这台是一个兄弟给俺的，拿来时不开机，修复后其他一切都OK，就是没无线信号，频道都已经是固定的了，是否能用TTL输出的数据判断问题出在哪儿？
   4：俺小白第一次用CRT，正常开机的输出数据似乎很多，等开机完俺再回到最前面看似乎最前面的数据已经没了，在哪儿设置页面可以保留更多的数据？
有请各位指教，先谢谢了。。。

zy900114 · 发表于 2014-3-9 12:48

第一台重新刷一下不就得了

gjs · 发表于 2014-3-9 15:45

zy900114 发表于 2014-3-9 12:48
第一台重新刷一下不就得了

兄弟，要是重刷一下就OK的话俺就不用来请教了。。。
启动到Verifying Checksum ... Bad Data CRC，就直接进入
Starting httpd to update firmware...
要不俺把TTL信息贴上来您帮忙看看？

zy900114 · 发表于 2014-3-9 21:02

很可能FLASH坏了，换一片试试

gjs · 发表于 2014-3-9 23:46

zy900114 发表于 2014-3-9 21:02
很可能FLASH坏了，换一片试试

fkash是最早代换过的，并且还和正常开机的机子代换过，二者刷相同的固件（N14U）。。。确认flash无问题。。。
不正常开机的TTL信息如下
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)

SoC:MediaTek MT7620
DRAM:  Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

______________________________________________________
| ____                         ____             |
|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |
|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |
|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  < |
|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |
|                                                 |
|                DreamBox Team                   |
|          http://www.openwrt.org.cn             |
|             Board:Mercury MW305R                |
|                                                 |
|       lintel<lintel.huang@gmail.com>          |
|____________________________________________________|

===============System Info==================
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes

Build Date:Jan 29 2013  Time:15:41:44
============================================

GPIO Init:
      UARTF_SHARE_MODE:GPIO
      I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12978901 Bytes = 12.4 MB
Load Address: 80000000
Entry Point:  8000c150
raspi_read: from:50040 len:c60ad5
Verifying Checksum ... Bad Data CRC

Starting httpd to update firmware...
raspi_read: from:40028 len:6

NetTxPacket = 0x83FE4400

KSEG1ADDR(NetTxPacket) = 0xA3FE4400

NetLoop,call eth_halt !
Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start... done

ETH_STATE_ACTIVE!!
______________________________________________________
| ____                         ____             |
|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |
|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |
|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  < |
|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |
|                                                 |
|          HTTPD Recovery Module v1.0          |
|                                                 |
| Note

lease Use Web Browser Upgrade the Firmware ! |
|                                                 |
|       lintel<lintel.huang@gmail.com>          |
|             Copyright 2005-2012                |
|____________________________________________________|

uHttpd Server started.
IP: 192.168.1.1
Netmask:255.255.255.0
Default Router:255.255.255.255

zy900114 · 发表于 2014-3-10 09:31

FLASH周围电阻有没有掉

gjs · 发表于 2014-3-10 13:16

zy900114 发表于 2014-3-10 09:31
FLASH周围电阻有没有掉

这些俺都对比过，还测过阻值，未发现问题，见图。。。现在俺疑惑的是很多东东似乎是矛盾的。。。
1：从TTL数据看似乎是FLASH数据有问题，但俺不但重写过FLASH，还和能正常开机的机子互换过。。。
2：俺就动过FLASH和RAM，从TTL数据俺看不出RAM有问题。。。俺也换过一次RAM，或者俺再换一片新的试试？为了验证TTL数据对RAM的检测，俺人为破坏了RAM的一个脚的连接，TTL数据显示这时数据变化了，RAM变成1M的了，这似乎说明了RAM没问题。。。

yyrtnn · 发表于 2014-3-10 16:33

换片FLASH试试吧

huangchao222 · 发表于 2014-3-10 16:41

重刷固件，也可能你的固件本身就不对，8m的flash的内核居然显示有12m多。

gjs · 发表于 2014-3-10 17:28

huangchao222 发表于 2014-3-10 16:41
重刷固件，也可能你的固件本身就不对，8m的flash的内核居然显示有12m多。

兄弟，是16M的FLASH，用编程器刷过多次的，而且和正常开机的机子的FLASH互换过，再上个正常开机的TTL信息，这个正常开机的别的都正常，就是无线信号无。。。
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)

SoC:MediaTek MT7620
DRAM:  Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

______________________________________________________
| ____                         ____             |
|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |
|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |
|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  < |
|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |
|                                                 |
|                DreamBox Team                   |
|          http://www.openwrt.org.cn             |
|             Board:Mercury MW305R                |
|                                                 |
|       lintel<lintel.huang@gmail.com>          |
|____________________________________________________|

===============System Info==================
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes

Build Date:Jan 29 2013  Time:15:41:44
============================================

GPIO Init:
      UARTF_SHARE_MODE:GPIO
      I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12978901 Bytes = 12.4 MB
Load Address: 80000000
Entry Point:  8000c150
raspi_read: from:50040 len:c60ad5
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 64

Starting kernel ...

LINUX started...

THIS IS ASIC
Linux version 2.6.36 (root@asus) (gcc version 4.2.4) #1 Wed Jan 30 16:05:53 CST 2013

The CPU feqenuce set to 580 MHz
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
PCIE: PLL power down for MT7620N
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00014f9f
Readback ErrCtl register=00014f9f
Memory: 61500k/65536k available (2647k kernel code, 4036k reserved, 547k data, 172k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Load Ralink Timer0 Module
Load Ralink Timer1 Module
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 120
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : c2 20 18 c2 20 (2018c220)
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
partion 3: ffffffff f30000
partion 4: 16a580 e15a80
#add mtd partition#
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "nvram"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000f80000 : "linux"
0x00000016a580-0x000000f80000 : "rootfs"
0x000000f80000-0x000001000000 : "jffs2"
0x000000000000-0x000001000000 : "ALL"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
IMQ driver loaded successfully. (numdevs = 16, numqueues = 1)
      Hooking IMQ after NAT on PREROUTING.
      Hooking IMQ before NAT on POSTROUTING.
u32 classifier
nf_conntrack version 0.5.0 (960 buckets, 3840 max)
matchsize=264
xt_time: kernel timezone is -0000
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Bridge firewalling registered
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
SQUASHFS error: Xattrs in filesystem, these will be ignored
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 172k freed
offset 0x1000 elapse 0ms
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq0 ACTION=add
hotplug net INTERFACE=imq1 ACTION=add
hotplug net INTERFACE=imq11 ACTION=add
hotplug net INTERFACE=imq12 ACTION=add
hotplug net INTERFACE=imq14 ACTION=add
hotplug net INTERFACE=imq10 ACTION=add
hotplug net INTERFACE=imq3 ACTION=add
hotplug net INTERFACE=imq5 ACTION=add
hotplug net INTERFACE=eth2 ACTION=add
hotplug net INTERFACE=imq13 ACTION=add
hotplug net INTERFACE=imq15 ACTION=add
hotplug net INTERFACE=imq2 ACTION=add
hotplug net INTERFACE=imq4 ACTION=add
hotplug net INTERFACE=imq7 ACTION=add
hotplug net INTERFACE=imq8 ACTION=add
hotplug net INTERFACE=imq9 ACTION=add
hotplug net INTERFACE=lo ACTION=add
hotplug net INTERFACE=imq6 ACTION=add
set_action 0

Hit ENTER for console...

clean_mode(1) clean_time(2) threshold(0)
free_caches: Start syncing...
free_caches: Start cleaning...
free_caches: waiting 2 second...
free_caches: Finish.
bootloader version: RT-N14U-0000
firmware version: 3.0.0.4
[1 init:init_nvram +16] init_nvram for 4
Algorithmics/MIPS FPU Emulator v1.5
config_switch(0x00de): link down all ports
config_switch(0x00ef): STB port: 0
config_switch(0x0208): link up wan port(s)
rt2860v2_ap: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint

=== pAd = c0508000, size = 626600 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.2
hotplug net INTERFACE=ra0 ACTION=add
/ # check_action 0
*** jffs2: 5, 524288
[1 init:init_main +21] main loop signal/state=17
start_logger:
start_usb
_iRaeth v3.0 (fcTaskleton,SkbRecyclefi)
g: n
phy_tx_ring = 0x0265e000, tx_ring = 0xa265e000

phy_rx_ring0 = 0x02664000, rx_ring0 = 0xa2664000
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762058
amCDMA_CSG_CFG = 81000000
e=GDMA1_FWD_CFG = 20710000
eth2 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=vlan1 ACTION=add
hotplug net INTERFACE=vlan2 ACTION=add
start_lan 868
update_lan_state(lan_, 0, 0)
start_lan: setting up the bridge br0
_ifconfig: name=vlan1 flags=1043 IFUP addr=(null) netmask=(null)
start_lan: setting MAC of br0 bridge to 00:0C:43:76:20:58
gen ralink config
hotRX DESC a2db4000  size = 2048
plug net INTERFACE=br0 ARTMP_TimerListAdd: add timer obj c0571c88!
CTRTMP_TimerListAdd: add timer obj c05100c8!
IORTMP_TimerListAdd: add timer obj c050fcbc!
N=RTMP_TimerListAdd: add timer obj c0510098!
adRTMP_TimerListAdd: add timer obj c0510430!
RTMP_TimerListAdd: add timer obj c0510190!

wRTMP_TimerListAdd: add timer obj c05101c0!
arRTMP_TimerListAdd: add timer obj c0510370!
niRTMP_TimerListAdd: add timer obj c0513330!
ngRTMP_TimerListAdd: add timer obj c0512f24!
: RTMP_TimerListAdd: add timer obj c0513300!
41RTMP_TimerListAdd: add timer obj c0513698!
!!RTMP_TimerListAdd: add timer obj c05133f8!
!!RTMP_TimerListAdd: add timer obj c0513428!

RTMP_TimerListAdd: add timer obj c05135d8!
MiRTMP_TimerListAdd: add timer obj c0516598!
ssRTMP_TimerListAdd: add timer obj c051618c!
sRTMP_TimerListAdd: add timer obj c0516568!
omRTMP_TimerListAdd: add timer obj c0516900!
e RTMP_TimerListAdd: add timer obj c0516660!
coRTMP_TimerListAdd: add timer obj c0516690!
nfRTMP_TimerListAdd: add timer obj c0516840!
igRTMP_TimerListAdd: add timer obj c0519800!
urRTMP_TimerListAdd: add timer obj c05193f4!
atRTMP_TimerListAdd: add timer obj c05197d0!
ioRTMP_TimerListAdd: add timer obj c0519b68!
n,RTMP_TimerListAdd: add timer obj c05198c8!
pRTMP_TimerListAdd: add timer obj c05198f8!
leRTMP_TimerListAdd: add timer obj c0519aa8!
asRTMP_TimerListAdd: add timer obj c051ca68!
e RTMP_TimerListAdd: add timer obj c051c65c!
chRTMP_TimerListAdd: add timer obj c051ca38!
ecRTMP_TimerListAdd: add timer obj c051cdd0!
k!RTMP_TimerListAdd: add timer obj c051cb30!
!!RTMP_TimerListAdd: add timer obj c051cb60!
RTMP_TimerListAdd: add timer obj c051cd10!

_RTMP_TimerListAdd: add timer obj c051fcd0!
ifRTMP_TimerListAdd: add timer obj c051f8c4!
coRTMP_TimerListAdd: add timer obj c051fca0!
nfRTMP_TimerListAdd: add timer obj c0520038!
igRTMP_TimerListAdd: add timer obj c051fd98!
: RTMP_TimerListAdd: add timer obj c051fdc8!
naRTMP_TimerListAdd: add timer obj c051ff78!
meRTMP_TimerListAdd: add timer obj c0522f38!
=rRTMP_TimerListAdd: add timer obj c0522b2c!
a0RTMP_TimerListAdd: add timer obj c0522f08!
fRTMP_TimerListAdd: add timer obj c05232a0!
laRTMP_TimerListAdd: add timer obj c0523000!
gsRTMP_TimerListAdd: add timer obj c0523030!
=1RTMP_TimerListAdd: add timer obj c05231e0!
04RTMP_TimerListAdd: add timer obj c05261a0!
3 RTMP_TimerListAdd: add timer obj c0525d94!
IFRTMP_TimerListAdd: add timer obj c0526170!
UPRTMP_TimerListAdd: add timer obj c0526508!
aRTMP_TimerListAdd: add timer obj c0526268!
ddRTMP_TimerListAdd: add timer obj c0526298!
r=RTMP_TimerListAdd: add timer obj c0526448!
(nRTMP_TimerListAdd: add timer obj c0529408!
ulRTMP_TimerListAdd: add timer obj c0528ffc!
l)RTMP_TimerListAdd: add timer obj c05293d8!
nRTMP_TimerListAdd: add timer obj c0529770!
etRTMP_TimerListAdd: add timer obj c05294d0!
maRTMP_TimerListAdd: add timer obj c0529500!
skRTMP_TimerListAdd: add timer obj c05296b0!
=(RTMP_TimerListAdd: add timer obj c052c670!
nuRTMP_TimerListAdd: add timer obj c052c264!
llRTMP_TimerListAdd: add timer obj c052c640!
RTMP_TimerListAdd: add timer obj c052c9d8!

RTMP_TimerListAdd: add timer obj c052c738!
RTMP_TimerListAdd: add timer obj c052c768!
RTMP_TimerListAdd: add timer obj c052c918!
RTMP_TimerListAdd: add timer obj c052f8d8!
RTMP_TimerListAdd: add timer obj c052f4cc!
RTMP_TimerListAdd: add timer obj c052f8a8!
RTMP_TimerListAdd: add timer obj c052fc40!
RTMP_TimerListAdd: add timer obj c052f9a0!
RTMP_TimerListAdd: add timer obj c052f9d0!
RTMP_TimerListAdd: add timer obj c052fb80!
RTMP_TimerListAdd: add timer obj c0532b40!
RTMP_TimerListAdd: add timer obj c0532734!
RTMP_TimerListAdd: add timer obj c0532b10!
RTMP_TimerListAdd: add timer obj c0532ea8!
RTMP_TimerListAdd: add timer obj c0532c08!
RTMP_TimerListAdd: add timer obj c0532c38!
RTMP_TimerListAdd: add timer obj c0532de8!
RTMP_TimerListAdd: add timer obj c0535da8!
RTMP_TimerListAdd: add timer obj c053599c!
RTMP_TimerListAdd: add timer obj c0535d78!
RTMP_TimerListAdd: add timer obj c0536110!
RTMP_TimerListAdd: add timer obj c0535e70!
RTMP_TimerListAdd: add timer obj c0535ea0!
RTMP_TimerListAdd: add timer obj c0536050!
RTMP_TimerListAdd: add timer obj c0539010!
RTMP_TimerListAdd: add timer obj c0538c04!
RTMP_TimerListAdd: add timer obj c0538fe0!
RTMP_TimerListAdd: add timer obj c0539378!
RTMP_TimerListAdd: add timer obj c05390d8!
RTMP_TimerListAdd: add timer obj c0539108!
RTMP_TimerListAdd: add timer obj c05392b8!
RTMP_TimerListAdd: add timer obj c053c278!
RTMP_TimerListAdd: add timer obj c053be6c!
RTMP_TimerListAdd: add timer obj c053c248!
RTMP_TimerListAdd: add timer obj c053c5e0!
RTMP_TimerListAdd: add timer obj c053c340!
RTMP_TimerListAdd: add timer obj c053c370!
RTMP_TimerListAdd: add timer obj c053c520!
RTMP_TimerListAdd: add timer obj c053f4e0!
RTMP_TimerListAdd: add timer obj c053f0d4!
RTMP_TimerListAdd: add timer obj c053f4b0!
RTMP_TimerListAdd: add timer obj c053f848!
RTMP_TimerListAdd: add timer obj c053f5a8!
RTMP_TimerListAdd: add timer obj c053f5d8!
RTMP_TimerListAdd: add timer obj c053f788!
RTMP_TimerListAdd: add timer obj c05485f4!
RTMP_TimerListAdd: add timer obj c0548710!
RTMP_TimerListAdd: add timer obj c0548620!
RTMP_TimerListAdd: add timer obj c053fb74!
RTMP_TimerListAdd: add timer obj c050d548!
RTMP_TimerListAdd: add timer obj c05107b0!
RTMP_TimerListAdd: add timer obj c0513a18!
RTMP_TimerListAdd: add timer obj c0516c80!
RTMP_TimerListAdd: add timer obj c0519ee8!
RTMP_TimerListAdd: add timer obj c051d150!
RTMP_TimerListAdd: add timer obj c05203b8!
RTMP_TimerListAdd: add timer obj c0523620!
RTMP_TimerListAdd: add timer obj c0526888!
RTMP_TimerListAdd: add timer obj c0529af0!
RTMP_TimerListAdd: add timer obj c052cd58!
RTMP_TimerListAdd: add timer obj c052ffc0!
RTMP_TimerListAdd: add timer obj c0533228!
RTMP_TimerListAdd: add timer obj c0536490!
RTMP_TimerListAdd: add timer obj c05396f8!
RTMP_TimerListAdd: add timer obj c053c960!
RTMP_TimerListAdd: add timer obj c053f888!
APSDCapable[0]=1
APSDCapable[1]=1
APSDCapable[2]=1
APSDCapable[3]=1
APSDCapable[4]=1
APSDCapable[5]=1
APSDCapable[6]=1
APSDCapable[7]=1
APSDCapable[8]=1
APSDCapable[9]=1
APSDCapable[10]=1
APSDCapable[11]=1
APSDCapable[12]=1
APSDCapable[13]=1
APSDCapable[14]=1
APSDCapable[15]=1
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 6
2. Phy Mode = 6
E2PROM: D0 target power=0xff20
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 6
RTMP_TimerListAdd: add timer obj c050d140!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = -3, D2 = 2, CalCode = 12 !!!
RT6352_Temperature_Init : BBPR49 = 0xfffffffe
RT6352_Temperature_Init : TemperatureRef25C = 0xffffffef
Current Temperature from BBP_R49=0xffffffee
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= 0, phase=3b)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 0, phase= 0)
TX IQ Calibration Done!
internal ALC is not enabled in NVM !
MCS Set = ff ff 00 00 01
ADC clcok selection for E3 !!!
Shielding clock selection !!!
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
RTMP_TimerListAdd: add timer obj c05400fc!
ADC clcok selection for E3 !!!
Shielding clock selection !!!
Main bssid = 00:0c:43:76:20:58
<==== rt28xx_init, Status=0
0x1300 = 00064320
hotplug net INTERFACE=wds3 ACTION=add
_ifconfig: name=wds3 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=wds1 ACTION=add
_ifconfig: name=wds1 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=wds2 ACTION=add
_ifconfig: name=wds2 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=wds0 ACTION=add
_ifconfig: name=wds0 flags=1043 IFUP addr=(null) netmask=(null)
[doSystem] iwpriv ra0 set TxPower=100
_ifconfig: name=br0 flags=1043 IFUP addr=192.168.1.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
update_lan_state(lan_, 2, 0)

set default filter settings
stop_nat_rules: apply the redirect_rules!
start_lan 1261
start_services  2487
start wsc start_wsc_pin_enrollee()
# wanduck: nvram changed: x_Setting=1, link_modem=0.
# wanduck: Got LAN(-1) information:

# Enable direct rule
[doSystem] iwpriv ra0 set WscConfMode=7
WPS: PIN
[doSystem] iwpriv ra0 set WscMode=1
[1 init:start_dnsmasq +30] begin
[1 init:start_dnsmasq +30] end
start_lan_port(0) 1
[doSystem] iwpriv ra0 set WatchdogPid=4428
set watchdog pid as: 4428
[doSystem] iwpriv ra0 set WatchdogPid=4428
decomp: fname=/var/lib/misc/rstats-speed.gz
set watchdog pid as: 4428
decomp: gzip -dc /var/lib/misc/rstats-speed.gz > /var/tmp/rstats-uncomp != 0
load: speed_count = 0
load: read source= save_path=
load_history: fname=/var/lib/misc/rstats-history.gz
decomp: fname=/var/lib/misc/rstats-history.gz
TZ watchdog
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
decomp: fname=/var/lib/misc/rstats-history.gz
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
load_history: load failed
[1 init:start_upnp +30] config 5
start_pptpd: getpid= 1
start_wan_if(0)
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
** wan_ifname: vlan2 is NOT UP
_ifconfig: name=vlan2 flags=1043 IFUP addr=(null) netmask=(null)
start_auth:: done
update_wan_state(wan0_, 1, 0)
start_wan_if(): End.
udhcpc_wan:: deconfig
_ifconfig: name=vlan2 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
wan_down(vlan2)
wan_down(vlan2): .
stop_auth:: done
eval(rtkswitch, 41) ret(0)
route_manip: cmd=DEL name=vlan2 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
eval(iwpriv, ra0, stat) ret(0)
clean_mode(1) clean_time(2) threshold(0)
free_caches: Start syncing...
free_caches: Start cleaning...
U2EC starting ...
free_caches: waiting 2 second...
free_caches: Finish.
[1 init:init_main +33] main loop signal/state=14
udhcpc_wan:: leasefail

gjs · 发表于 2014-3-10 17:29

zy900114 发表于 2014-3-9 21:02
很可能FLASH坏了，换一片试试

兄弟，早就换过，一样的现象，还和正常开机的机子互换过FLASH。。。

zy900114 · 发表于 2014-3-10 18:02

要是那片FLASH在第二台机器能过，那么第一台机器的内存很可能有缺陷

zy900114 · 发表于 2014-3-10 18:04

我遇到过这个情况，各种不稳定，但是似乎又没坏的样子，最后还是换内存解决，顺便说一句，第一台机器的C108掉了

gjs · 发表于 2014-3-10 19:51

zy900114 发表于 2014-3-10 18:02
要是那片FLASH在第二台机器能过，那么第一台机器的内存很可能有缺陷

有道理，这也是俺提的问题的一部分，开机时的检测内存到底是怎么检测的，俺去找片新的来试试。。。。

gjs · 发表于 2014-3-10 19:53

zy900114 发表于 2014-3-10 18:04
我遇到过这个情况，各种不稳定，但是似乎又没坏的样子，最后还是换内存解决，顺便说一句，第一台机器的C108 ...

C108？在哪儿？俺没找到啊，不是那个2.5V的滤波电容吧？俺特意没装的。。。

账号		自动登录	找回密码
密码			立即注册

小白又有新问题来请教了

相关帖子

本帖子中包含更多资源