|
本帖最后由 danielwidelan 于 2015-8-3 11:57 编辑
 u¬-boot信息
U-Boot 1.1.4 (Jul 31 2015 - 04:43:21)
ap143 - Honey Bee 2.0DRAM:
sri
Honey Bee 2.0
ath_ddr_initial_config(196): (16bit) ddr2 init
Tap (low, high) = (0x4f107ed, 0xf01776f9)
Tap values = (0x10, 0x5, 0x5, 0x5)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 198k for U-Boot at: 87fcc000
Reserving 192k for malloc() at: 87f9c000
Reserving 44 Bytes for Board Info at: 87f9bfd4
Reserving 36 Bytes for Global Data at: 87f9bfb0
Reserving 128k for boot params() at: 87f7bfb0
Stack Pointer at: 87f7bf98
Now running in RAM - U-Boot at: 87fcc000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
 方案信息:
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (gier@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Fri Jul 31 00:42:48 PDT 2015
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9531 rev 2
[ 0.000000] Clocks: CPU:650.000MHz, DDR:391.772MHz, AHB:216.666MHz, Ref:25.000MHz
 USB支持
[ 9.160000] usbcore: registered new interface driver usbfs
[ 9.170000] usbcore: registered new interface driver hub
[ 9.170000] usbcore: registered new device driver usb
[ 9.590000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.590000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[ 9.600000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 9.640000] ehci-platform ehci-platform.0: irq 3, io mem 0x1b000000
[ 9.660000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 9.660000] hub 1-0:1.0: USB hub found
[ 9.670000] hub 1-0:1.0: 1 port detected
[ 9.730000] Initializing USB Mass Storage driver...
[ 9.730000] usbcore: registered new interface driver usb-storage
[ 9.740000] USB Mass Storage support registered.
 LAN/WAN/WLAN支持
[ 36.150000] fuse init (API version 7.18)
[ 39.620000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 40.670000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 40.690000] device eth1 entered promiscuous mode
[ 40.690000] ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 40.710000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 41.630000] eth0: link up (100Mbps/Full duplex)
[ 41.630000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 48.850000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 48.870000] device wlan0 entered promiscuous mode
[ 48.890000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 48.900000] br-lan: port 2(wlan0) entered forwarding state
[ 48.910000] br-lan: port 2(wlan0) entered forwarding state
[ 48.910000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 48.930000] ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 50.910000] br-lan: port 2(wlan0) entered forwarding state
|
|