网件6300刷机变砖，能进CFE，能上传固件反复重启

roy***

上传完后反复重启，弹出如下日志，TTL和TFTP刷固件都不行， 求大神帮忙哦
Decompressing...done


CFE for Foxconn Router R6300v2 version: v1.0.16
Build Date: Thu Dec 12 17:57:15 CST 2013
Init Arena
Init Devs.
Boot up from NAND flash...
Boot partition size = 262144(0x40000)
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=800,*533*
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.15.7 (r437571)
CPU type 0x0: 800MHz
Tot mem: 262144 KBytes

Device eth0:  hwaddr B0-7F-B9-84-A3-70, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: .... 4639328 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: found no supported devices
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x380000
nflash: squash filesystem with lzma found at block 42
Creating 16 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000200000 : "nvram"
0x000000200000-0x000000220000 : "board_data"
0x000000220000-0x000000240000 : "OT1"
0x000000240000-0x000000260000 : "OT2"
0x000000260000-0x000000280000 : "T_Meter1"
0x000000280000-0x0000002a0000 : "T_Meter2"
0x0000002a0000-0x0000002c0000 : "ML1"
0x0000002c0000-0x0000002e0000 : "ML2"
0x0000002e0000-0x000000300000 : "ML3"
0x000000300000-0x000000320000 : "ML4"
0x000000320000-0x000000340000 : "ML5"
0x000000340000-0x000000360000 : "ML6"
0x000000360000-0x000000380000 : "ML7"
0x000000380000-0x000002180000 : "linux"
0x000000547314-0x000002180000 : "rootfs"
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: irq 111, io mem 0x18021000
ehci_hcd 0000:00:0b.1: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: irq 111, io mem 0x18022000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci_hcd 0000:00:0c.0: xHCI Host Controller
xhci_hcd 0000:00:0c.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:00:0c.0: irq 112, io mem 0x18023000
xhci_hcd 0000:00:0c.0: Failed to enable MSI-X
xhci_hcd 0000:00:0c.0: failed to allocate MSI entry
usb usb3: No SuperSpeed endpoint companion for config 1  interface 0 altsetting 0 ep 129: using minimum values
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
u32 classifier
    Actions configured
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
Spare area=64 eccbytes 56, ecc bytes located at:
2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
Available 7 bytes at (off,len):
(1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0)
Scanning device for bad blocks
Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,
Creating 1 MTD partitions on "brcmnand":
0x000002180000-0x000008000000 : "brcmnand"
VFS: Mounted root (squashfs filesystem) readonly on device 31:15.
devtmpfs: mounted
Freeing init memory: 188K
SQUASHFS error: xz_dec_run error, data probably corrupt
SQUASHFS error: squashfs_read_data failed to read block 0x548b74
SQUASHFS error: Unable to read fragment cache entry [548b74]
SQUASHFS error: Unable to read page, block 548b74, size be18
SQUASHFS error: Unable to read fragment cache entry [548b74]
SQUASHFS error: Unable to read page, block 548b74, size be18
SQUASHFS error: Unable to read fragment cache entry [548b74]
SQUASHFS error: Unable to read page, block 548b74, size be18
SQUASHFS error: Unable to read fragment cache entry [548b74]
SQUASHFS error: Unable to read page, block 548b74, size be18
SQUASHFS error: Unable to read fragment cache entry [548b74]
SQUASHFS error: Unable to read page, block 548b74, size be18
Failed to execute /sbin/preinit.  Attempting defaults...
SQUASHFS error: Unable to read fragment cache entry [548b74]
SQUASHFS error: Unable to read page, block 548b74, size be18
SQUASHFS error: xz_dec_run error, data probably corrupt
SQUASHFS error: squashfs_read_data failed to read block 0x60
SQUASHFS error: Unable to read data cache entry [60]
SQUASHFS error: Unable to read page, block 60, size e484
SQUASHFS error: Unable to read data cache entry [60]
SQUASHFS error: Unable to read page, block 60, size e484
SQUASHFS error: Unable to read data cache entry [60]
SQUASHFS error: Unable to read page, block 60, size e484
SQUASHFS error: Unable to read data cache entry [60]
SQUASHFS error: Unable to read page, block 60, size e484
SQUASHFS error: Unable to read data cache entry [60]
SQUASHFS error: Unable to read page, block 60, size e484
Kernel panic - not syncing: No init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[<c003d2d0>] (unwind_backtrace+0x0/0xe4) from [<c034de24>] (panic+0x68/0x184)
[<c034de24>] (panic+0x68/0x184) from [<c0037388>] (init_post+0x9c/0xbc)
[<c0037388>] (init_post+0x9c/0xbc) from [<c0008bb0>] (kernel_init+0x110/0x14c)
[<c0008bb0>] (kernel_init+0x110/0x14c) from [<c0038970>] (kernel_thread_exit+0x0/0x8)
Rebooting in 3 seconds..Digital core power voltage set to 0.9375V
Decompressing...done
Digital core power voltage set to 0.9375V

SHMOO VER 1.13

PKID07DC06011801080000000000001A103F01000000

S3004026F
00001D90


RDLYW0 00000004

RDENW0 00000042

RDQSW0

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
00 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
01 -----------++++++++++++++++++++++++++X++++++++++++++++++++++++++
02 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
03 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
04 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
05 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
06 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
07 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++
08 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
09 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++
10 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
11 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++
12 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
13 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
14 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
15 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++


PW0

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
00 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++
01 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++
02 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++
03 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
04 --+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++
05 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++
06 ----++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
07 -------++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
08 -+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
09 -------++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
10 --+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++
11 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
12 ++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
13 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++
14 -+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
15 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++


NW0

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
00 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
01 -----------++++++++++++++++++++++++++X++++++++++++++++++++++++++
02 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
03 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
04 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
05 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
06 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
07 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++
08 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
09 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++
10 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
11 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
12 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
13 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
14 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
15 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++


WRDQW0

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
00 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
01 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
02 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
03 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
04 ++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++---
05 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
06 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
07 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
08 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
09 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
10 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
11 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
12 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
13 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
14 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
15 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-


WRDMW0 00000030
WRDMW0 00000031


ADDR

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
00 +++++++++++++++++++++++++++++S+X++++++++++++++++++++++++++++++++

Decompressing...done

roy***

想问下这个是什么问题，为何会反复重启，明明固件上传完了，就是重启后没反应

samso***

你是怎么刷的固件？

roy***

samson9913 发表于 2018-7-2 21:42
你是怎么刷的固件？

就是刷梅林时候刷失败了，然后就一直反复重启，电脑配192重启后一两秒内能ping通，之后再重启，我现在是TFTP能上传固件，完了后一重启又老样子

samso***

可能分区不对乱了所以才这样

roy***

samson9913 发表于 2018-7-2 22:11
可能分区不对乱了所以才这样

那怎么把分区搞了呢？正常情况我觉得刷进系统应该就能启动，我是每个版本都试过，就是起不来

roy***

royyou 发表于 2018-7-2 21:35
想问下这个是什么问题，为何会反复重启，明明固件上传完了，就是重启后没反应

我也不知道啊，网上找的方式都试过，就是启动不了，现在都不重启了，从TTL上看   卡在一个界面上了，一直黄灯，除启动时候是四个灯依次闪

nxh***

清除nvram试试

nxh***

之后TFTP传官方固件看看

roy***

nxh1129 发表于 2018-7-3 11:37
之后TFTP传官方固件看看

官方的版本都传过，不起作用哦

roy***

nxh1129 发表于 2018-7-3 11:35
清除nvram试试

怎么清理呢？在CFE下清理？现在不反复重启了，启动停下来了，一直亮橙色灯，还是可以上传固件，进CFE

nxh***

ttl，超级终端里，按住Ctrl+C不放，路由器加电，直到看见下面的字样


然后把下边代码，分两次复制粘贴进去，每次都回车
nvram erase
nvram commit

nxh***

刷完梅林，进去过梅林界面吗？

roy***

nxh1129 发表于 2018-7-3 11:59
刷完梅林，进去过梅林界面吗？

没有啊，现在从在CFE下用TFTP上传上去都启动不了，感觉上传完后不解压固件包，感谢像是引导之类的问题

nxh***

12楼的图，如果能看见，就已经能进miniweb了，此时在网页中就可以执行nvram清除