大家帮我看看我的TTL信息那个地方错了

hxs***

我的wr841n从DD-WRT涮回来原厂固件，结果涮完后直接变砖头。按此方法（https://www.right.com.cn/forum/thread-40302-1-2.html）在官网下的固件
现在的现象是开机后，第一和最后一个灯会同时间隔1s闪一次。接上USBR的TTL线可以进入，但是重刷官网的固件还是一样，PWR灯常，SYS灯和QSS时间隔1s闪一次，有谁遇到这种问题的啊。

C?ㄕ浇褋1.1.4 (Nov 16 2009 - 09:06:24)

AP93 (ar7240) U-boot
DRAM:  
sri
#### TAP VALUE 1 = a, 2 = b
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP ERROR - must RESET board to recover

Resetting...
U-Boot 1.1.4 (Nov 16 2009 - 09:06:24)

AP93 (ar7240) U-boot
DRAM:  
sri
#### TAP VALUE 1 = a, 2 = b
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds

ar7240> tftpboot
dup 1 speed 1000
*** Warning: no boot file name; using '7B01A8C0.img'
Using eth1 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.123
Filename '7B01A8C0.img'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######################################################
done
Bytes transferred = 3932160 (3c0000 hex)
ar7240> erase 0x9f020000 +0x3c0000

First 0x2 last 0x3d sector size 0x10000
  61
Erased 60 sectors
ar7240> cp.b 0x80000000 0x9f020000 0x3c0000
Copy to Flash... write addr: 9f020000
done
bootm 0x9f020000
U-Boot 1.1.4 (Nov 16 2009 - 09:06:24)

AP93 (ar7240) U-boot
DRAM:  
sri
#### TAP VALUE 1 = a, 2 = b
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds

lh***

ar7240> erase 0x9f020000 +0x3c0000
ar7240> cp.b 0x81000000 0x9f020000 0x3c0000

ar7100> reset

hxs***

ar7240> erase 0x9f020000 +0x3c0000
ar7240> cp.b 0x81000000 0x9f020000 0x3c0000

ar7100> reset
lhsz 发表于 2011-1-22 12:35

呵呵。成功了，谢谢楼上的