贝曼ha210s，刷三动swc001固件各位大大求助！

00:0***

贝曼ha210s，刷三动swc001固件后，连不上路由，ttl显示正常，求助！
路由硬该了一个lan口，8196c+8188芯片的路由，网线连接灯指示正常。
TBS bootloader V1.0 (Jul 26 2011 - 19:47:28)

DRAM:  16 MB
Flash:  4 MB
kernel_offset=0x60000,rootfs_offset=0x14d8a4
system supports single image and version is R2
Register rtl8196ceth device.
  Set 8196C PHY Patch OK
IP: 192.168.1.1 MAC: f4:3e:61:aa:bb:84
Hit Space or Enter key to stop autoboot:  0
Checking image, please wait ...
## Transferring Linux code from 0xbfc60000 to 0x80010000... ##ok!
Starting kernel ...
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 11356k/16384k available (2480k kernel code, 5028k reserved, 600k data, 1
12k init, 0k highmem)
Calibrating delay loop... 389.12 BogoMIPS (lpj=1945600)
Mount-cache hash table entries: 512
net_namespace: 524 bytes
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Realtek GPIO Driver for Flash Reload Default
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x18002000 (irq = 23) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
RTL8192C/RTL8188C driver version 1.4 (2010-12-22)
=====>>INSIDE rtl8192cd_init_one <<=====
vendor_deivce_id=819110ec
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====



Probing RTL8186 10/100 NIC-kenel stack size order[2]...
chip name: 8196C, chip revid: 0
Set 8196C PHY Patch OK
NOT YET
Set threshould idx 0
eth0 added. vid=9 Member port 0x10...
eth1 added. vid=8 Member port 0x1...
eth2 added. vid=10 Member port 0x8...
eth3 added. vid=11 Member port 0x4...
eth4 added. vid=12 Member port 0x2...
[peth0] added, mapping to [eth1]...
SPI INIT
flash device: 0x400000 at 0xbfe00000
SPI 1

********************************************************************************

*
* chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize
*        0   c22016       c2       20       16        0       16   400000
* blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName
*    10000       40     1000      400      100       10       4e MX25L3205D
*
********************************************************************************

spi_flash: Found an alies 0x400000 for the chip at 0x0, MX25L3205D device detect
.
3 cmdlinepart partitions found on MTD device spi_flash
Creating 3 MTD partitions on "spi_flash":
0x000000000000-0x000000060000 : "boot"
0x000000060000-0x00000014d8a4 : "kernel"
mtd: partition "kernel" doesn't end on an erase block -- force read-only
0x00000014d8a4-0x000000400000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-o
nly
flash chips probe ok!
---rtl8196c_btns[0].gpio-5-
---rtl8196c_btns[1].gpio-3-
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (256 buckets, 1024 max)
rtl_nf_conntrack_threshold:896
icmp=20  tcp=614  udp=614
ctnetlink v0.93: registering with nfnetlink.
nf_conntrack_ipsec loaded
nf_conntrack_l2tp version 3.1 loaded
nf_conntrack_rtsp v0.6.21 loading
xt_time: kernel timezone is -0000
---->luotao ipport netspy test Driver.....-->
NETSPY IPPORT proc module 1.0 initialized
GRE over IPv4 tunneling driver
nf_nat_ipsec loaded
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team

ipt_conenat_init for cone nat nf_conntrack
TCP cubic registered
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 112k freed
init started: BusyBox v1.6.1 (2012-06-14 15:42:40 HKT) multi-call binary
starting pid 13, tty '/dev/console': '/etc/init.d/rcS'
@@@@@@@Welcome to TBS System@@@@@@@
Sat Jan  1 12:00:00 UTC 2011
var/
var/run/
var/cache/
var/cache/dproxy.cache
var/iproute2/
var/iproute2/rt_scopes
var/iproute2/rt_dsfield
var/iproute2/rt_realms
var/iproute2/rt_protos
var/iproute2/rt_tables
var/iproute2/ematch_map
var/siproxd.conf
var/udhcpd.conf
var/dproxy.conf
var/igmpproxy.conf
var/mtab
var/tmp/
var/tmp/TZ
var/log/
var/log/lastlog
var/log/wtmp
var/lib/
var/lib/misc/
var/devlog
var/miniupnpd.conf
var/pid/
var/hosts
var/inetd.conf
var/resolv.conf
var/mon.conf
mount: mounting none on /proc/bus/usb failed
=============Begin Load Modules==============
=============End Load Modules================
/etc/init.d/rcS: line 29: /etc/init.d/wlan.rc: not found
cp: cannot stat '/etc/wps': No such file or directory
/etc/init.d/rcS: line 41: cannot create /proc/sys/net/ipv6/conf/all/forwarding:
nonexistent directory
rtl_nf_conntrack_threshold:1920
icmp=40  tcp=1228  udp=1228
rtl_nf_conntrack_threshold:1920
icmp=40  tcp=1228  udp=1228
starting pid 44, tty '/dev/ttyS0': '/bin/sh'


BusyBox v1.6.1 (2012-06-14 15:42:40 HKT) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

#
*** TBS ver:41150, compile time:Jul 18 2012,10:14:09 ***

0000s.[CCP] logic.c: 264                 main: Logic Start
Set coredump file size to 2147483647, path = /var/core
[system]: echo 0 > /proc/qos
[system]: echo "flush" > /proc/filter_table
Reading config from /etc/config_full.xml ...
Reading config from tbs_app_cfg ...
!!!!!!!!!Read config failed!!!!!!!!!!!
Reading config from tbs_app_cfg_bak ...
!!!!!!!!!Read config failed!!!!!!!!!!!
Reading config from /etc/config.xml ...
0001s.[CCP] logic.c: 294                 main: CMM_ModuleInit
0001s.[CCP] logic.c: 298                 main: TIMER_ModuleInit
0001s.[CCP] logic.c: 302                 main: tbsDeleteAllChains
0001s.[CCP] logic.c: 305                 main: MSG_AllModStartOK
0002s.[CCP] logic.c: 314                 main: DEVINFO
---------LOGGER_UnregisterTimer-------
0002s.[CCP] logic.c: 314                 main: LOGGER
[system]: ifconfig eth1 up
Can't get low config
Faild to get mac.
[system]: ethtool -s eth1 autoneg on 2>/dev/null 1>&2
0002s.[CCP] logic.c: 314                 main: ETHWAN
[system]: ebtables -N WHITE 2>/dev/null 1>&2
[system]: ebtables -P WHITE DROP 2>/dev/null 1>&2
[system]: ifconfig eth0 down;ifconfig eth0 hw ether 800656cc0000;ifconfig eth0 u
p
[system]: ifconfig eth0 up
[system]: ethtool -s eth0 phyad 0 autoneg on 2>/dev/null 1>&2
[system]: ethtool -s eth0 phyad 1 autoneg on 2>/dev/null 1>&2
[system]: ethtool -s eth0 phyad 2 autoneg on 2>/dev/null 1>&2
[system]: ethtool -s eth0 phyad 3 autoneg on 2>/dev/null 1>&2
0002s.[CCP] logic.c: 314                 main: ETHLAN
[system]: ifconfig br0 down 2>/dev/null 1>&2
[system]: brctl delbr br0 2>/dev/null 1>&2
[system]: brctl addbr br0
[system]: brctl setfd br0 1
Can't get low config
Faild to get mac.
/usr/bin/logic: logic.c: 313: main: Assertion `(nRet == TBS_SUCCESS)' failed.
/usr/bin/logic unnomal exited!

gor***

cfe不一样吧

duyi***

每天多看帖，每天多交流，拿金币走人