N1砖机，短接用t1救砖包不行，换EMMC芯片也不行，大神帮看看吧!

cynizy

1. 大神们往下看
   
2. 从正常的机器上拆的emmc换上不能启动，显示代码如下：

复制代码

1. GXL:BL1:9ac50e:bb16dc;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;CHK:A7;READ:0;CHK:A7;READ:0;CHK:A7;SD:800;USB:8;LOOP:1;EMMC:0;READ:0;CHK:A7;READ:0;CHK:A7;READ:0;CHK:A7;SD:800;USB:8;LOOP:2;EMMC:0;READ:0;CHK:A7;READ:0;CHK:A7;READ:0;CHK:A7;SD:800;USB:8;LOOP:3;EMMC:0;READ:0;CHK:A7;READ:0;CHK:A7;READ:0;CHK:A7;SD:800;USB:8;e

复制代码

不死心，用T1-N1救砖包，ttl显示刷机成功，代码如下：

1. BL2 Built : 11:58:42, May 27 2017.
   
2. gxl gc3c9a84 - xiaobo.gu@droid05
   
3. 
   
4. set vdd cpu_a to 1120 mv
   
5. set vdd cpu_b to 1050 mv
   
6. set vddee to 1000 mv
   
7. Board ID = 4
   
8. CPU clk: 1200MHz
   
9. BL2 USB
   
10. DQS-corr enabled
    
11. DDR scramble enabled
    
12. DDR3 chl: Rank0+1 [url=home.php?mod=space&uid=162986]@[/url] 912MHz
    
13. Rank0: 1024MB-2T-13
    
14. Rank1: 1024MB-2T-13
    
15. 0.0;CHK:0;
    
16. TE: 165130474
    
17. 
    
18. BL2 Built : 11:58:42, May 27 2017.
    
19. gxl gc3c9a84 - xiaobo.gu@droid05
    
20. 
    
21. set vdd cpu_a to 1120 mv
    
22. set vdd cpu_b to 1050 mv
    
23. set vddee to 1000 mv
    
24. Board ID = 4
    
25. CPU clk: 1200MHz
    
26. BL2 USB
    
27. 0.0;CHK:0;
    
28. TE: 165177274
    
29. 
    
30. BL2 Built : 11:58:42, May 27 2017.
    
31. gxl gc3c9a84 - xiaobo.gu@droid05
    
32. 
    
33. set vdd cpu_a to 1120 mv
    
34. set vdd cpu_b to 1050 mv
    
35. set vddee to 1000 mv
    
36. Board ID = 4
    
37. CPU clk: 1200MHz
    
38. BL2 USB
    
39. Load fip header from USB, src: 0x0000c000, des: 0x01400000, size: 0x00004000
    
40. New fip structure!
    
41. Load bl30 from USB, src: 0x00010000, des: 0x01100000, size: 0x0000d600
    
42. Load bl31 from USB, src: 0x00020000, des: 0x05100000, size: 0x0002c600
    
43. Load bl33 from USB, src: 0x00050000, des: 0x01000000, size: 0x00065400
    
44. NOTICE:  BL3-1: v1.0(release):a625749
    
45. NOTICE:  BL3-1: Built : 11:25:15, Aug 25 2017
    
46. [BL31]: GXL CPU setup!
    
47. NOTICE:  BL31: BL33 decompress pass
    
48. mpu_config_enable:ok
    
49. [Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
    
50. OPS=0x04
    
51. b9 6b b6 6 7 70 4a f6 3 4e 76 4f [165.413481 Inits done]
    
52. secure task start!
    
53. high task start!
    
54. low task start!
    
55. ERROR:   Error initializing runtime service opteed_fast
    
56. 
    
57. 
    
58. U-Boot 2015.01-dirty (Dec 22 2017 - 10:20:14)
    
59. 
    
60. DRAM:  2 GiB
    
61. Relocation Offset is: 76eb8000
    
62. [MSG]MMC init in usb
    
63. aml_priv->desc_buf = 0x0000000073eb8640
    
64. aml_priv->desc_buf = 0x0000000073eba960
    
65. SDIO Port B: 0, SDIO Port C: 1
    
66. InUsbBurn
    
67. [MSG]sof
    
68. Set Addr 2
    
69. Get DT cfg
    
70. Get DT cfg
    
71. Get DT cfg
    
72. set CFG
    
73. 
    
74. ID[16]
    
75. tplcmd[    echo 12345]
    
76. 12345
    
77. [MSG]ret = 0
    
78. [info]success
    
79. BULKcmd[    low_power]
    
80. [info]success
    
81. 
    
82. ID[16]
    
83. tplcmd[    download mem dtb normal 45518]
    
84. [MSG]Down(mem) part(dtb) sz(0xb1ce) fmt(normal)
    
85. [MSG]totalSlotNum = 0, nextWriteBackSlot 1
    
86. [info]success
    
87. [MSG]Burn Start...
    
88. [MSG]load dt.img to 0x0000000001000000, sz=0xb1ce
    
89. [MSG]Burn complete
    
90. BULKcmd[download get_status]
    
91. [info]success
    
92. BULKcmd[disk_initial 1]
    
93. dtb magic edfe0dd0
    
94.       Amlogic multi-dtb tool
    
95.       Single dtb detected
    
96. start dts,buffer=0000000001000000,dt_addr=0000000001000000
    
97.       Amlogic multi-dtb tool
    
98.       Single dtb detected
    
99. parts: 10
    
100. 00:      logo   0000000002000000 1
     
101. 01:  recovery   0000000002000000 1
     
102. 02:       rsv   0000000000800000 1
     
103. 03:       tee   0000000000800000 1
     
104. 04:     crypt   0000000002000000 1
     
105. 05:      misc   0000000002000000 1
     
106. 06:      boot   0000000002000000 1
     
107. 07:    system   0000000080000000 1
     
108. 08:     cache   0000000020000000 2
     
109. 09:      data   ffffffffffffffff 4
     
110. emmc/sd response timeout, cmd8, status=0x1ff2800
     
111. emmc/sd response timeout, cmd55, status=0x1ff2800
     
112. init_part() 293: PART_TYPE_AML
     
113. [mmc_init] mmc init success
     
114. _cmp_partition()-570: name: system<->system
     
115. _cmp_partition()-571: size: 80000000<->50000000
     
116. _cmp_partition()-572: offset: 36c00000<->36c00000
     
117. _cmp_partition()-573: mask: 00000001<->00000001
     
118. _cmp_iptbl()-609: partition 11 has changed
     
119. mmc_device_init()-1115: update rsv with dtb!
     
120. init_part() 293: PART_TYPE_AML
     
121. eMMC/TSD partition table have been checked OK!
     
122. check pattern success
     
123. XXXXXXX======enter EMMC boot======XXXXXX
     
124. emmc/sd response timeout, cmd8, status=0x1ff2800
     
125. emmc/sd response timeout, cmd55, status=0x1ff2800
     
126. init_part() 293: PART_TYPE_AML
     
127. [mmc_init] mmc init success
     
128. switch to partitions #0, OK
     
129. mmc1(part 0) is current device
     
130. Device: SDIO Port C
     
131. Manufacturer ID: 88
     
132. OEM: 103
     
133. Name: NCard
     
134. Tran Speed: 52000000
     
135. Rd Block Len: 512
     
136. MMC version 5.1
     
137. High Capacity: Yes
     
138. Capacity: 7.3 GiB
     
139. mmc clock: 40000000
     
140. Bus Width: 8-bit
     
141. [store]amlmmc erase 1emmckey_is_protected : protect
     
142. start = 0,end = 57343
     
143. 
     
144. 
     
145. Caution! Your devices Erase group is 0x400
     
146. The erase range would be change to 0x36000~0xe8ffff
     
147. 
     
148. start = 221184,end = 15269886
     
149. [MSG]usb producing env_relocate
     
150. mmc env offset: 0x27400000
     
151. *** Warning - bad CRC, using default environment
     
152. 
     
153. Saving Environment to aml-storage...
     
154. mmc env offset: 0x27400000
     
155. Writing to MMC(1)... done
     
156.       Amlogic multi-dtb tool
     
157.       Single dtb detected
     
158. [info]success
     
159. 
     
160. ID[16]
     
161. tplcmd[download store _aml_dtb normal 46624]
     
162. [MSG]Down(store) part(_aml_dtb) sz(0xb620) fmt(normal)
     
163. [MSG]totalSlotNum = 0, nextWriteBackSlot 1
     
164. [info]success
     
165. [MSG]Burn Start...
     
166. [MSG]optimus_download_dtb_image:dataSzReceived=0xb620
     
167. start erase dtb......
     
168. start = 81920,end = 82943
     
169. dev # 1,  , several blocks erased OK
     
170. [store]To run cmd[emmc dtb_write 0x0000000007700000 0x40000]
     
171. dtb_write()-1140: valid 0
     
172. dtb_write()-1160: new stamp 0, checksum 0xf01d52fa, version 1, magic A~D
     
173. dtb magic 71b104da
     
174.       Amlogic multi-dtb tool
     
175.       Cannot find legal dtb!
     
176. start dts,buffer=0000000007700000,dt_addr=0000000007700000
     
177. check_valid_dts: FDT_ERR_BADMAGIC
     
178. [MSG]Burn complete
     
179. BULKcmd[download get_status]
     
180. [info]success
     
181. BULKcmd[verify sha1sum a4749b00aad894244fa753c72be0e4a539e40b26]
     
182. [store]To run cmd[emmc dtb_read 0x0000000007700000 0x40000]
     
183. dtb_read_shortcut()-975: short cut in...
     
184. [MSG]VERIFY OK
     
185. [info]success
     
186. 
     
187. ID[16]
     
188. tplcmd[download store boot normal 9976320]
     
189. [MSG]flash LOGIC partCap 0x2000000B
     
190. [MSG]Down(store) part(boot) sz(0x983a00) fmt(normal)
     
191. [MSG]totalSlotNum = 0, nextWriteBackSlot 1
     
192. [info]success
     
193. [MSG]Burn Start...
     
194. [MSG]Burn complete
     
195. BULKcmd[download get_status]
     
196. [info]success
     
197. BULKcmd[verify sha1sum 6fc9cad684b02c0083555bb0637f05f82489de24]
     
198. [MSG]Verify Start...
     
199. [MSG]To verify part boot in fmt normal
     
200. [MSG]Verify End
     
201. [MSG]VERIFY OK
     
202. [info]success
     
203. 
     
204. ID[16]
     
205. tplcmd[download store data sparse 183336060]
     
206. [MSG]flash LOGIC partCap 0x11ac00000B
     
207. [MSG]Down(store) part(data) sz(0xaed7c7c) fmt(sparse)
     
208. [MSG]totalSlotNum = 0, nextWriteBackSlot 1024
     
209. [info]success
     
210. [MSG]Burn Start...
     
211. MMC: block number 0xeba010 exceeds max(0xe90000)
     
212. amlmmc cmd <NULL> failed
     
213. 
     
214. store - STORE sub-system
     
215. 
     
216. Usage:
     
217. store store init flag
     
218. store read name addr off|partition size
     
219.     read 'size' bytes starting at offset 'off'
     
220.     to/from memory address 'addr', skipping bad blocks.
     
221. store write name addr off|partition size
     
222.     write 'size' bytes starting at offset 'off'
     
223.     to/from memory address 'addr', skipping bad blocks.
     
224. store rom_write add off size.
     
225.         write uboot to the boot device
     
226. store erase boot/data:
     
227.         erase the area which is uboot or data
     
228. store erase partition <partition_name>:
     
229.         erase the area which partition in u-boot
     
230. store erase dtb
     
231. store erase key
     
232. store disprotect key
     
233. store rom_protect on/off
     
234. store scrub off|partition size
     
235.         scrub the area from offset and size
     
236. store dtb iread/read/write addr <size>
     
237.         read/write dtb, size is optional
     
238. store key read/write addr <size>
     
239.         read/write key, size is optional
     
240. store mbr addr
     
241.    update mbr/partition table by dtb
     
242. 
     
243. [burnup]Err:store_write_ops,L110:cmd [store  write data 0xa5616e8  0x120000000  0x2000] failed ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_download.c)L239:Fail to write to media, ret = -1
     
244. ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_simg2img.c)L187:Fail to write to flash, want to write 8192B, but 0B
     
245. ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_download.c)L256:Fail in parse simg. src 0x00000000076ff070, size 0x2ed8c0c, unParsedDataLen 0x0, ret -188
     
246. ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_download.c)L575:Fail in optimus_storage_write, data 0x00000000076ff070, wantSz 0x2ed8c0c
     
247. ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_buffer_manager.c)L242:this burn size 0 <= last left size 3984, data 0x00000000076ff070
     
248. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L821:media error 1 at seq 44752
     
249. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 1
     
250. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 2
     
251. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 3
     
252. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 0
     
253. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 1
     
254. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 2
     
255. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 3
     
256. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 0
     
257. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 1
     
258. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 2
     
259. ERR(../drivers/usb/gadget/v2_burning/v2_usb_tool/usb_pcd.c)L797:media error 1 at seq 44752, resend 3
     
260. 
     
261. ID[16]
     
262. BULKcmd[upload mem 0xc8100228 normal 0x4]
     
263. [MSG]Down(mem) part(0xc8100228) sz(0x4) fmt(normal)
     
264. [MSG]totalSlotNum = 0, nextWriteBackSlot 0
     
265. [info]success
     
266. [MSG]Burn Start...
     
267. [MSG]Burn complete
     
268. 
     
269. ID[16]
     
270. tplcmd[    echo 12345]
     
271. 12345
     
272. [MSG]ret = 0
     
273. [info]success
     
274. BULKcmd[    low_power]
     
275. [info]success
     
276. 
     
277. ID[16]
     
278. tplcmd[    download mem dtb normal 89120]
     
279. [MSG]Down(mem) part(dtb) sz(0x15c20) fmt(normal)
     
280. [MSG]totalSlotNum = 0, nextWriteBackSlot 2
     
281. [info]success
     
282. [MSG]Burn Start...
     
283. [MSG]load dt.img to 0x0000000001000000, sz=0x15c20
     
284. [MSG]Burn complete
     
285. BULKcmd[download get_status]
     
286. [info]success
     
287. BULKcmd[disk_initial 0]
     
288. [MSG]Disk inited again.
     
289. [info]success
     
290. 
     
291. ID[16]
     
292. tplcmd[download store _aml_dtb normal 89120]
     
293. [MSG]Down(store) part(_aml_dtb) sz(0x15c20) fmt(normal)
     
294. [MSG]totalSlotNum = 0, nextWriteBackSlot 2
     
295. [info]success
     
296. [MSG]Burn Start...
     
297. [MSG]optimus_download_dtb_image:dataSzReceived=0x15c20
     
298. start erase dtb......
     
299. start = 81920,end = 82943
     
300. dev # 1,  , several blocks erased OK
     
301. [store]To run cmd[emmc dtb_write 0x0000000007700000 0x40000]
     
302. dtb_write()-1140: valid 2
     
303. dtb_write()-1160: new stamp 1, checksum 0x619e8f20, version 1, magic A~D
     
304. dtb magic 71b104da
     
305.       Amlogic multi-dtb tool
     
306.       Cannot find legal dtb!
     
307. start dts,buffer=0000000007700000,dt_addr=0000000007700000
     
308. check_valid_dts: FDT_ERR_BADMAGIC
     
309. [MSG]Burn complete
     
310. BULKcmd[download get_status]
     
311. [info]success
     
312. BULKcmd[verify sha1sum dfc2b2e7a335949facb3b37eef85fb575a654150]
     
313. [store]To run cmd[emmc dtb_read 0x0000000007700000 0x40000]
     
314. dtb_read_shortcut()-975: short cut in...
     
315. [MSG]VERIFY OK
     
316. [info]success
     
317. 
     
318. ID[16]
     
319. tplcmd[download store boot normal 14191104]
     
320. [MSG]flash LOGIC partCap 0x2000000B
     
321. [MSG]Down(store) part(boot) sz(0xd88a00) fmt(normal)
     
322. [MSG]totalSlotNum = 0, nextWriteBackSlot 1
     
323. [info]success
     
324. [MSG]Burn Start...
     
325. [MSG]Burn complete
     
326. BULKcmd[download get_status]
     
327. [info]success
     
328. BULKcmd[verify sha1sum 1a0d04db8fb57f252c72c909a3268b6b2c3bd241]
     
329. [MSG]Verify Start...
     
330. [MSG]To verify part boot in fmt normal
     
331. [MSG]Verify End
     
332. [MSG]VERIFY OK
     
333. [info]success
     
334. 
     
335. ID[16]
     
336. tplcmd[download store logo normal 5048640]
     
337. [MSG]flash LOGIC partCap 0x2000000B
     
338. [MSG]Down(store) part(logo) sz(0x4d0940) fmt(normal)
     
339. [MSG]totalSlotNum = 0, nextWriteBackSlot 1
     
340. [info]success
     
341. [MSG]Burn Start...
     
342. [MSG]Burn complete
     
343. BULKcmd[download get_status]
     
344. [info]success
     
345. BULKcmd[verify sha1sum 0cdb3ab703c402566df2bb945e81a0813d23c35c]
     
346. [MSG]Verify Start...
     
347. [MSG]To verify part logo in fmt normal
     
348. [MSG]Verify End
     
349. [MSG]VERIFY OK
     
350. [info]success
     
351. 
     
352. ID[16]
     
353. tplcmd[download store recovery normal 18295296]
     
354. [MSG]flash LOGIC partCap 0x2000000B
     
355. [MSG]Down(store) part(recovery) sz(0x1172a00) fmt(normal)
     
356. [MSG]totalSlotNum = 0, nextWriteBackSlot 1
     
357. [info]success
     
358. [MSG]Burn Start...
     
359. [MSG]Burn complete
     
360. BULKcmd[download get_status]
     
361. [info]success
     
362. BULKcmd[verify sha1sum b468a3134b376a5295c1fd5857343128d0ac056c]
     
363. [MSG]Verify Start...
     
364. [MSG]To verify part recovery in fmt normal
     
365. [MSG]Verify End
     
366. [MSG]VERIFY OK
     
367. [info]success
     
368. 
     
369. ID[16]
     
370. tplcmd[download store system sparse 951586352]
     
371. [MSG]flash LOGIC partCap 0x80000000B
     
372. [MSG]Down(store) part(system) sz(0x38b80e30) fmt(sparse)
     
373. [MSG]totalSlotNum = 0, nextWriteBackSlot 1024
     
374. [info]success
     
375. [MSG]Burn Start...
     
376. [MSG]CHUNK_TYPE_FILL
     
377. [MSG]Burn complete
     
378. Downloading %100
     
379. BULKcmd[download get_status]
     
380. [info]success
     
381. BULKcmd[verify sha1sum 649d6c0813146b28de91f3a749b1f974518d7b85]
     
382. [MSG]Verify Start...
     
383. [MSG]To verify part system in fmt sparse
     
384. [MSG]Verify End
     
385. [MSG]VERIFY OK
     
386. [info]success
     
387. 
     
388. ID[16]
     
389. tplcmd[download store bootloader normal 672256]
     
390. [MSG]Down(store) part(bootloader) sz(0xa4200) fmt(normal)
     
391. [MSG]totalSlotNum = 0, nextWriteBackSlot 11
     
392. [info]success
     
393. [MSG]Burn Start...
     
394. mmc switch to boot0 success
     
395. mmc switch to boot1 success
     
396. mmc switch to user success
     
397. [MSG]align bootloader sz from 0xa4200 to 0xa8000
     
398. [MSG]Burn complete
     
399. BULKcmd[download get_status]
     
400. [info]success
     
401. BULKcmd[verify sha1sum 3a1ffcadf062748ca1d00eb80e73f2175b160a0d]
     
402. mmc switch to boot0 success
     
403. mmc switch to boot1 success
     
404. mmc switch to user success
     
405. [MSG]VERIFY OK
     
406. [info]success
     
407. BULKcmd[save_setting]
     
408. ## save_setting ##
     
409. [MSG]Set upgrade_step to 2
     
410. Saving Environment to aml-storage...
     
411. mmc env offset: 0x27400000
     
412. Writing to MMC(1)... done
     
413. [info]success
     
414. BULKcmd[burn_complete 3]
     
415. [MSG]Pls un-plug USB line to poweroff

复制代码

然后断电开机，代码又变成这样：

1. GXL:BL1:9ac50e:bb16dc;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;CHK:A7;READ:0;CHK:A7;READ:0;CHK:A7;SD:800;USB:8;LOOP:1;EMMC:0;READ:0;CHK:A7;READ:0;CHK:A7;READ:0;CHK:A7;SD:800;USB:8;LOOP:2;EMMC:0;READ:0;CHK:A7;READ:0;CHK:A7;READ:0;CHK:A7;SD:800;USB:8;LOOP:3;EMMC:0;READ:0;CHK:A7;READ:0;CHK:A7;READ:0

复制代码

砖机一块，希望大神们帮忙看看还能救么？

772787180

你可以找个好的导出然后写入emmc然后在吹上去试试，也可能cpu废了吧

萱和安

我的N1短接强刷识别不到硬件，ttl无反应，无输出，不知道换emmc有没有用啊

萱和安

就只剩一个灯亮了。

cynizy

萱和安 发表于 2020-7-30 08:29
就只剩一个灯亮了。

两个灯都亮

asdde

不懂帮顶。是不是之前固件刷emmc了

cynizy

萱和安 发表于 2020-7-30 08:28
我的N1短接强刷识别不到硬件，ttl无反应，无输出，不知道换emmc有没有用啊

指示灯亮么？

萱和安

cynizy 发表于 2020-8-8 23:30
指示灯亮么？

两个都亮，像你样换了emmc,还是坏的，已经拆件了

cynizy

萱和安 发表于 2020-8-9 12:17
两个都亮，像你样换了emmc,还是坏的，已经拆件了

可能是供电问题啊，没查电路么？

bw0008

搞定了没

coollover999

我CM211-2 朝歌M8335 HI3798MV300H的  明明刷了备份的各分区文件 还是这样

Check Hisilicon_ADVCA ...
Not hisilicon ADVCA image ...
Wrong Image Format for bootm command
ERROR: can't get kernel image!
fastboot# env default -a
Unknown command 'env' - try 'help'
fastboot#

coollover999

哪位大侠看看什么无法加载内核映像的还是啥的？