K2T使用TTL刷机时无法中断自动启动（已解决）

斯巴***

应该是K2T主板上的插针没有焊好，重新焊了一下问题解决了


使用USB TTL连接电脑和K2T，用XShell 连接成功，显示


Connecting to COM5...
Connected.




然后插上K2T电源，不停地按回车键，XShell显示

U-Boot 1.1.4-gbc73b198 (Mar 29 2018 - 15:36:58)

ap152 - Dragonfly 1.0DRAM:  
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0xf, 0xf, 0xf, 0xf)
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 202k for U-Boot at: 83fcc000
Reserving 192k for malloc() at: 83f9c000
Reserving 44 Bytes for Board Info at: 83f9bfd4
Reserving 36 Bytes for Global Data at: 83f9bfb0
Reserving 128k for boot params() at: 83f7bfb0
Stack Pointer at: 83f7bf98
Now running in RAM - U-Boot at: 83fcc000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment

Power up PLL with outdiv = 0 then switch to 3
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x4b962100
Hit any key to stop autoboot:  0
## Booting image at 9f090000 ...
   Image Name:   MIPS OpenWrt Linux-3.3.8
   Created:      2018-06-08   3:53:19 UTC
   Image Type:   MIPS Linux Multi-File Image (lzma compressed)
   Data Size:    1046996 Bytes = 1022.5 kB
   Load Address: 80060000
   Entry Point:  80060000
   Contents:
   Image 0:  1046988 Bytes = 1022.4 kB
   Verifying Checksum at 0x9f090040 ...OK
   Uncompressing Multi-File Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...




看到了Hit any key to stop autoboot:  0 ，拼命按回车键都没有stop autoboot，我还以为我手速太慢，然后用了连发软件，还是没有成功，直到路由器红灯变成黄灯
fast-classifier: starting up
fast-classifier: registered
phicomm id:4(pid:1791) connect ok!


我用putty也试过，同样的问题
求助各位大神，请问出现这种情况是什么原因啊？有什么解决办法啊？

7727***

都忘了。需要了我这有全新135刷好包邮。你也可以邮寄过来30包邮回弄好

九木***

按住回车键再插k2t电源