|
|
2023年5月9号出厂的CMCC A10，无需拆开刷机，只需要用3根缝衣针插入TTL相应孔位即可。
图1图2图3是本论坛其他先行者给出的拆机图，要多看几遍
把路由器底部朝上，用手电筒对准图4图5相应孔位依次插入3根缝衣针
插入后要反复从不同角度检查确认是否正确，以及缝衣针不要互相接触。
然后用TTL的TX接RX,RX接TX,GND接GND。
开机跑码后，按键盘F和回车，会进入failsafe模式，然后按照刷360T7的方式一步一步做，
360T7会看到输出root@(none):/#，而CMCC A10会看到CMCCAdmin@(none):/#
360T7依次输入以下三行代码
fw_setenv bootmenu_delay 3
mount_root
sed -i 's/.*local debug=.*/\tlocal debug=1/' /etc/init.d/telnet
而CMCC A10输入第一行就不太一样，所以接下来的步骤应该没什么作用。俗话说:一步错，步步错。所以请大神看代码后请给出正确的操作步骤。
Xshell 7 (Build 0128)
Copyright (c) 2020 NetSarang Computer, Inc. All rights reserved.
Type `help' to learn how to use Xshell prompt.
[C:\~]$
Connecting to COM3...
Connected.
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024F [010F]
Jump to BL
NOTICE: BL2: v2.7(release):99e2c4319-dirty
NOTICE: BL2: Built : 00:03:22, Feb 17 2023
NOTICE: WDT: disabled
NOTICE: EMI: Using DDR3 settings
dump toprgu registers data:
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000
dump drm registers data:
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a083f1 000003ff 00100000 00000000
1001d040 | 00000000 00000000 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0x8
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0
BYTE_swap:0
Window Sum 572, worse bit 1, min window 68
Window Sum 560, worse bit 8, min window 68
Window Sum 356, worse bit 4, min window 42
Window Sum 316, worse bit 11, min window 34
Window Sum 326, worse bit 11, min window 36
Window Sum 360, worse bit 3, min window 42
Window Sum 332, worse bit 11, min window 36
Window Sum 366, worse bit 1, min window 44
Window Sum 336, worse bit 11, min window 36
Window Sum 372, worse bit 1, min window 44
Window Sum 346, worse bit 11, min window 40
Window Sum 386, worse bit 3, min window 46
Window Sum 352, worse bit 11, min window 40
Window Sum 360, worse bit 11, min window 40
Window Sum 388, worse bit 1, min window 46
Window Sum 360, worse bit 11, min window 42
Window Sum 376, worse bit 11, min window 42
Window Sum 392, worse bit 1, min window 48
Window Sum 374, worse bit 11, min window 44
Window Sum 378, worse bit 11, min window 44
NOTICE: EMI: Detected DRAM size: 256MB
NOTICE: EMI: complex R/W mem test passed
NOTICE: CPU: MT7981 (1300MHz)
NOTICE: SPI_NAND parses attributes from parameter page.
NOTICE: SPI_NAND Detected ID 0xc8
NOTICE: Page size 2048, Block size 131072, size 134217728
NOTICE: Initializing NMBM ...
NOTICE: Signature found at block 1023 [0x07fe0000]
NOTICE: First info table with writecount 0 found in block 960
NOTICE: Second info table with writecount 0 found in block 963
NOTICE: NMBM has been successfully attached in read-only mode
NOTICE: BL2: Booting BL31
NOTICE: BL31: v2.7(release):99e2c4319-dirty
NOTICE: BL31: Built : 00:03:26, Feb 17 2023
NOTICE: Hello BL31!!!
NOTICE: DDR:1866M!!!
U-Boot 2022.07-rc3 (Feb 16 2023 - 23:59:29 +0800)
CPU: MediaTek MT7981
Model: mt7981-rfb
DRAM: 256 MiB
Core: 36 devices, 16 uclasses, devicetree: embed
Initializing NMBM ...
spi-nand: spi_nand spi_nand@0: GigaDevice SPI NAND was found.
spi-nand: spi_nand spi_nand@0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
Could not find a valid device for nmbm0
Signature found at block 1023 [0x07fe0000]
First info table with writecount 0 found in block 960
Second info table with writecount 0 found in block 963
NMBM has been successfully attached
Loading Environment from MTD... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address - aa:90:e7:4d:77:b9
eth0: ethernet@15100000
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
ubi0: attaching mtd6
ubi0: scanning is finished
ubi0: attached mtd6 (name "ubi", size 64 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 1677675094
ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... OK
## Loading kernel from FIT Image at 46000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.4.194
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x460000e8
Data Size: 3341393 Bytes = 3.2 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x48080000
Entry Point: 0x48080000
Hash algo: crc32
Hash value: 621cfd6c
Hash algo: sha1
Hash value: 80aca7f849ae4a53f203052687830c3adc4d766f
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt mt7981-spim-nand-rfb device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x4632fe80
Data Size: 18540 Bytes = 18.1 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: e57822c0
Hash algo: sha1
Hash value: 7a7939c6ac8bfc04d24ccae4c3493fea696146c4
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x4632fe80
Uncompressing Kernel Image
Loading Device Tree to 000000004f7f1000, end 000000004f7f886b ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.4.194 (root@jimmywang) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r0-0e8a77c2)) #0 SMP Wed Apr 26 13:00:20 2023
[ 0.000000] Machine model: MediaTek MT7981 RFB
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] On node 0 totalpages: 64592
[ 0.000000] DMA32 zone: 1024 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 64592 pages, LIFO batch:15
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 20 pages/cpu s43800 r8192 d29928 u81920
[ 0.000000] pcpu-alloc: s43800 r8192 d29928 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 63568
[ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000
[ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack ff, heap allocff, heap freeff
[ 0.000000] Memory: 230784K/258368K available (6846K kernel code, 444K rwdata, 1940K rodata, 448K init, 289K bss, 27584K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] random: get_random_bytes called from start_kernel+0x2d4/0x420 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000003] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.008176] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=52000)
[ 0.018496] pid_max: default: 32768 minimum: 301
[ 0.023212] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.030474] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.039024] ASID allocator initialised with 65536 entries
[ 0.044523] rcu: Hierarchical SRCU implementation.
[ 0.049613] smp: Bringing up secondary CPUs ...
[ 0.054460] Detected VIPT I-cache on CPU1
[ 0.054481] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.054505] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.054569] smp: Brought up 1 node, 2 CPUs
[ 0.076182] SMP: Total of 2 processors activated.
[ 0.080908] CPU features: detected: 32-bit EL0 Support
[ 0.086070] CPU features: detected: CRC32 instructions
[ 0.091340] CPU: All CPU(s) started at EL2
[ 0.095462] alternatives: patching kernel code
[ 0.102252] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.112061] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.118962] pinctrl core: initialized pinctrl subsystem
[ 0.124728] NET: Registered protocol family 16
[ 0.129411] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.150632] SCSI subsystem initialized
[ 0.154574] libata version 3.00 loaded.
[ 0.158680] usbcore: registered new interface driver usbfs
[ 0.164260] usbcore: registered new interface driver hub
[ 0.169635] usbcore: registered new device driver usb
[ 0.175492] Bluetooth: Core ver 2.22
[ 0.179134] NET: Registered protocol family 31
[ 0.183604] Bluetooth: HCI device and connection manager initialized
[ 0.189994] Bluetooth: HCI socket layer initialized
[ 0.194895] Bluetooth: L2CAP socket layer initialized
[ 0.199977] Bluetooth: SCO socket layer initialized
[ 0.205110] rbus 18000000.wbsys: PCI host bridge to bus 0000:00
[ 0.211069] pci_bus 0000:00: root bus resource [mem 0x18000000-0x18ffffff]
[ 0.217980] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.223492] pci_bus 0000:00: scanning bus
[ 0.227532] pci 0000:00:00.0: [14c3:7981] type 00 class 0x000280
[ 0.233577] pci 0000:00:00.0: reg 0x10: [mem 0x18000000-0x1800000f 64bit]
[ 0.240402] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x0000000f]
[ 0.246701] pci 0000:00:00.0: reg 0x1c: [mem 0x00000000-0x0000000f]
[ 0.253000] pci 0000:00:00.0: reg 0x20: [mem 0x00000000-0x0000000f]
[ 0.259299] pci 0000:00:00.0: reg 0x24: [mem 0x00000000-0x0000000f]
[ 0.266429] pci_bus 0000:00: fixups for bus
[ 0.270643] pci_bus 0000:00: bus scan returning with max=00
[ 0.277004] clocksource: Switched to clocksource arch_sys_counter
[ 0.283794] thermal_sys: Registered thermal governor 'fair_share'
[ 0.283799] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.289943] thermal_sys: Registered thermal governor 'step_wise'
[ 0.295981] thermal_sys: Registered thermal governor 'user_space'
[ 0.302016] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.308376] NET: Registered protocol family 2
[ 0.319391] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.326919] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.335328] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.343125] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.350319] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.356763] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.363335] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.370413] NET: Registered protocol family 1
[ 0.374813] PCI: CLS 0 bytes, default 64
[ 0.379535] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[ 0.388946] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.394834] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.417967] phy phy-usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[ 0.433569] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.440656] printk: console [ttyS0] disabled
[ 0.465063] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 12, base_baud = 2500000) is a ST16650V2
[ 0.474274] printk: console [ttyS0] enabled
[ 0.474274] printk: console [ttyS0] enabled
[ 0.482636] printk: bootconsole [uart8250] disabled
[ 0.482636] printk: bootconsole [uart8250] disabled
[ 0.492932] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.501336] loop: module loaded
[ 0.504597] mediatek,mt2701-ice_debug ice_debug: get dbg_sel clock fail: -2
[ 0.511565] mediatek,mt2701-ice_debug: probe of ice_debug failed with error -2
[ 0.519632] mt7981-pinctrl 11d00000.pinctrl: pin_config_set op failed for pin 19
[ 0.527029] mtk-spi 1100a000.spi: Error applying setting, reverse things back
[ 0.534706] spi-nand spi0.0: GigaDevice SPI NAND was found.
[ 0.540304] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.550797] [mtk_hw_init] reset_lock:0, force:0
[ 0.555366] [mtk_hw_init] execute fe cold reset
[ 0.571155] mtk_soc_eth 15100000.ethernet: generated random MAC address 76:24:44:83:0e:b3
[ 0.579628] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc011800000, irq 75
[ 0.588702] mtk_soc_eth 15100000.ethernet: generated random MAC address be:2b:f3:c9:b9:d2
[ 0.597144] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc011800000, irq 75
[ 0.606192] (unnamed net_device) (dummy): netif_napi_add() called with weight 256
[ 0.614008] xhci-mtk 11200000.xhci: 11200000.xhci supply vbus not found, using dummy regulator
[ 0.622655] xhci-mtk 11200000.xhci: 11200000.xhci supply vusb33 not found, using dummy regulator
[ 0.631550] phy phy-usb-phy@11e10000.0: try to get sw efuse
[ 0.637125] phy phy-usb-phy@11e10000.1: try to get sw efuse
[ 0.642688] phy phy-usb-phy@11e10000.1: try to get sw efuse+
[ 0.648361] phy phy-usb-phy@11e10000.1: u3 efuse - intr 2f, rx_imp 12, tx_imp 12
[ 0.655783] phy_efuse_set set efuse, tx_imp 12, rx_imp 12 intr 2f
[ 0.661953] xhci-mtk 11200000.xhci: xHCI Host Controller
[ 0.667321] xhci-mtk 11200000.xhci: new USB bus registered, assigned bus number 1
[ 0.677782] xhci-mtk 11200000.xhci: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000210010
[ 0.687098] xhci-mtk 11200000.xhci: irq 85, io mem 0x11200000
[ 0.693307] hub 1-0:1.0: USB hub found
[ 0.697108] hub 1-0:1.0: 1 port detected
[ 0.701268] xhci-mtk 11200000.xhci: xHCI Host Controller
[ 0.706615] xhci-mtk 11200000.xhci: new USB bus registered, assigned bus number 2
[ 0.714106] xhci-mtk 11200000.xhci: Host supports USB 3.2 Enhanced SuperSpeed
[ 0.721288] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.729710] hub 2-0:1.0: USB hub found
[ 0.733489] hub 2-0:1.0: 1 port detected
[ 0.737846] usbcore: registered new interface driver uas
[ 0.743244] usbcore: registered new interface driver usb-storage
[ 0.749347] i2c /dev entries driver
[ 0.753758] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 0.761743] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com
[ 0.770288] Bluetooth: HCI UART driver ver 2.3
[ 0.774739] Bluetooth: HCI UART protocol H4 registered
[ 0.779875] Bluetooth: HCI UART protocol BCSP registered
[ 0.785263] Bluetooth: HCI UART protocol Broadcom registered
[ 0.790932] Bluetooth: HCI UART protocol QCA registered
[ 0.798253] NET: Registered protocol family 10
[ 0.803341] Segment Routing with IPv6
[ 0.807076] NET: Registered protocol family 17
[ 0.811572] Bridge firewalling registered
[ 0.815703] 8021q: 802.1Q VLAN Support v1.8
[ 0.829070] nmbm nmbm_spim_nand: Signature found at block 1023 [0x07fe0000]
[ 0.836905] nmbm nmbm_spim_nand: First info table with writecount 0 found in block 960
[ 0.847389] nmbm nmbm_spim_nand: Second info table with writecount 0 found in block 963
[ 0.855394] nmbm nmbm_spim_nand: NMBM has been successfully attached
[ 0.861996] 8 fixed-partitions partitions found on MTD device nmbm_spim_nand
[ 0.869041] Creating 8 MTD partitions on "nmbm_spim_nand":
[ 0.874520] 0x000000000000-0x000000100000 : "BL2"
[ 0.879752] 0x000000100000-0x000000180000 : "u-boot-env"
[ 0.885540] 0x000000180000-0x000000380000 : "Factory"
[ 0.891053] 0x000000380000-0x000000580000 : "FIP"
[ 0.896234] 0x000000580000-0x000004580000 : "ubi"
[ 0.901523] 0x000004580000-0x000006580000 : "firmware_backup"
[ 0.907790] 0x000006580000-0x000006680000 : "zrsave"
[ 0.913241] 0x000006680000-0x000006780000 : "config2"
[ 1.477042] mt753x gsw@0: LAN/WAN VLAN setting=llllw
[ 1.482280] mt753x gsw@0: Switch is MediaTek MT7531AE rev 1
[ 1.491707] mt753x gsw@0: HWSTRAP=0xff XTAL=25MHz
[ 5.137642] mt753x gsw@0: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION:
[ 5.145622] mt753x gsw@0: -------- gephy-calbration (port:0) --------
[ 5.160828] CALDLY = 40
[ 5.222870] 0x1e-e0 = 2929
[ 5.227272] 0x1f-115 = 5
[ 5.229798] GE Rext AnaCal Done! (9)(0x29)
[ 5.284771] GE R50 AnaCal Done! (8) (0x35)(0xb5)
[ 5.330590] GE R50 AnaCal Done! (7) (0x37)(0xb7)
[ 5.376410] GE R50 AnaCal Done! (7) (0x37)(0xb7)
[ 5.431340] GE R50 AnaCal Done! (9) (0x34)(0xb4)
[ 5.439103] GE 1e_174(0xb5b7), 1e_175(0xb7b4)
[ 5.480928] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220
[ 5.505796] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2221
[ 5.544330] GE Tx offset AnaCal Done! (pair-2)(5)(0x24) 0x1e_173=0x2420
[ 5.569198] GE Tx offset AnaCal Done! (pair-3)(2)(0x21) 0x1e_173=0x2421
[ 5.672165] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x380e)
[ 5.721458] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1b1b)
[ 5.808171] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x2129)
[ 5.843925] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x151d)
[ 5.890633] PORT 0 RX_DC_OFFSET
[ 5.903301] before pairA output = d
[ 5.908563] after pairA output = ff
[ 5.913745] before pairB output = f
[ 5.919009] after pairB output = ff
[ 5.924191] before pairC output = 1e
[ 5.929541] after pairC output = 1
[ 5.934631] before pairD output = 1d
[ 5.939981] after pairD output = ff
[ 5.943719] mt753x gsw@0: -------- gephy-calbration (port:1) --------
[ 5.958925] CALDLY = 40
[ 6.021048] GE R50 AnaCal Done! (11) (0x31)(0xb1)
[ 6.080618] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 6.140189] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 6.199761] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 6.207611] GE 1e_174(0xb1b2), 1e_175(0xb2b2)
[ 6.258547] GE Tx offset AnaCal Done! (pair-0)(5)(0x24) 0x1e_172=0x2420
[ 6.287969] GE Tx offset AnaCal Done! (pair-1)(3)(0x22) 0x1e_172=0x2422
[ 6.321945] GE Tx offset AnaCal Done! (pair-2)(4)(0x23) 0x1e_173=0x2320
[ 6.365029] GE Tx offset AnaCal Done! (pair-3)(6)(0x25) 0x1e_173=0x2325
[ 6.439693] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5014)
[ 6.522960] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2222)
[ 6.587024] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1e26)
[ 6.622783] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1921)
[ 6.669490] PORT 1 RX_DC_OFFSET
[ 6.682155] before pairA output = f
[ 6.687417] after pairA output = 0
[ 6.692512] before pairB output = e
[ 6.697774] after pairB output = fe
[ 6.702956] before pairC output = f
[ 6.708218] after pairC output = 1
[ 6.713314] before pairD output = e
[ 6.718571] after pairD output = 1
[ 6.722221] mt753x gsw@0: -------- gephy-calbration (port:2) --------
[ 6.737424] CALDLY = 40
[ 6.808646] GE R50 AnaCal Done! (13) (0x26)(0xa6)
[ 6.881888] GE R50 AnaCal Done! (13) (0x26)(0xa6)
[ 6.950570] GE R50 AnaCal Done! (12) (0x30)(0xb0)
[ 7.010142] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 7.017994] GE 1e_174(0xa6a6), 1e_175(0xb0b2)
[ 7.064375] GE Tx offset AnaCal Done! (pair-0)(4)(0x23) 0x1e_172=0x2320
[ 7.107464] GE Tx offset AnaCal Done! (pair-1)(6)(0x25) 0x1e_172=0x2325
[ 7.145996] GE Tx offset AnaCal Done! (pair-2)(5)(0x24) 0x1e_173=0x2420
[ 7.179978] GE Tx offset AnaCal Done! (pair-3)(4)(0x23) 0x1e_173=0x2423
[ 7.282957] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x8020)
[ 7.360562] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2020)
[ 7.481254] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x2931)
[ 7.550979] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1f27)
[ 7.597686] PORT 2 RX_DC_OFFSET
[ 7.610354] before pairA output = e
[ 7.615619] after pairA output = ff
[ 7.620801] before pairB output = 1d
[ 7.626151] after pairB output = fe
[ 7.631333] before pairC output = 1d
[ 7.636682] after pairC output = ff
[ 7.641864] before pairD output = 1e
[ 7.647213] after pairD output = fe
[ 7.650951] mt753x gsw@0: -------- gephy-calbration (port:3) --------
[ 7.666157] CALDLY = 40
[ 7.732836] GE R50 AnaCal Done! (12) (0x30)(0xb0)
[ 7.792409] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 7.856533] GE R50 AnaCal Done! (11) (0x31)(0xb1)
[ 7.920659] GE R50 AnaCal Done! (11) (0x31)(0xb1)
[ 7.928510] GE 1e_174(0xb0b2), 1e_175(0xb1b1)
[ 7.997666] GE Tx offset AnaCal Done! (pair-0)(9)(0x28) 0x1e_172=0x2820
[ 8.017979] GE Tx offset AnaCal Done! (pair-1)(1)(0x1) 0x1e_172=0x2801
[ 8.056423] GE Tx offset AnaCal Done! (pair-2)(5)(0x24) 0x1e_173=0x2420
[ 8.090402] GE Tx offset AnaCal Done! (pair-3)(4)(0x23) 0x1e_173=0x2423
[ 8.165060] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6c1b)
[ 8.203029] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1616)
[ 8.295412] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x242c)
[ 8.336828] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1b23)
[ 8.383534] PORT 3 RX_DC_OFFSET
[ 8.396202] before pairA output = f
[ 8.401464] after pairA output = 1
[ 8.406554] before pairB output = f
[ 8.411819] after pairB output = ff
[ 8.417004] before pairC output = 1d
[ 8.422349] after pairC output = fe
[ 8.427531] before pairD output = 1e
[ 8.432881] after pairD output = fe
[ 8.436617] mt753x gsw@0: -------- gephy-calbration (port:4) --------
[ 8.451819] CALDLY = 40
[ 8.509390] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 8.564410] GE R50 AnaCal Done! (9) (0x34)(0xb4)
[ 8.619339] GE R50 AnaCal Done! (9) (0x34)(0xb4)
[ 8.678823] GE R50 AnaCal Done! (10) (0x32)(0xb2)
[ 8.686673] GE 1e_174(0xb2b4), 1e_175(0xb4b2)
[ 8.728503] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220
[ 8.776147] GE Tx offset AnaCal Done! (pair-1)(7)(0x26) 0x1e_172=0x2226
[ 8.805568] GE Tx offset AnaCal Done! (pair-2)(3)(0x22) 0x1e_173=0x2220
[ 8.839549] GE Tx offset AnaCal Done! (pair-3)(4)(0x23) 0x1e_173=0x2223
[ 8.931190] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x4812)
[ 9.025786] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0xb0b)
[ 9.101089] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0xf17)
[ 9.159408] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x121a)
[ 9.206115] PORT 4 RX_DC_OFFSET
[ 9.218782] before pairA output = e
[ 9.224046] after pairA output = fe
[ 9.229228] before pairB output = 1e
[ 9.234571] after pairB output = 1
[ 9.239666] before pairC output = e
[ 9.244929] after pairC output = 1
[ 9.250024] before pairD output = d
[ 9.255286] after pairD output = 1
[ 9.261264] mt753x gsw@0: Port 2 Link is Up - 100Mbps/Full
[ 9.266967] UBI: auto-attach mtd5
[ 9.270293] ubi0: attaching mtd5
[ 9.274611] random: fast init done
[ 9.481291] ubi0: scanning is finished
[ 9.490226] ubi0: attached mtd5 (name "ubi", size 64 MiB)
[ 9.495628] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 9.502522] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 9.509300] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 9.516250] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[ 9.522245] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 9.529455] ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 1677675094
[ 9.538573] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 19
[ 9.547785] ubi0: background thread "ubi_bgt0d" started, PID 712
[ 9.554371] block ubiblock0_1: created from ubi0:1(rootfs)
[ 9.559876] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 9.566832] hctosys: unable to open rtc device (rtc0)
[ 9.575006] VFS: Mounted root (squashfs filesystem) readonly on device 253:0.
[ 9.582387] Freeing unused kernel memory: 448K
f[ 9.601043] Run /sbin/init as init process
f[ 9.808787] init: Console is alive
[ 9.812327] init: - watchdog -
f
f[ 10.073949] crng init done
f
f[ 10.407326] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 10.430668] conninfra@(mtk_conninfra_drv_init:644) Before platform_driver_register
[ 10.438356] Get Index(0-TOP_MISC_BASE) phy_addr(0x11d10000) vir_addr=(0xffffffc010ae5000) size=(0x1000)
[ 10.447744] Get Index(1-TOPRGU_BASE) phy_addr(0x1001c000) vir_addr=(0xffffffc010aed000) size=(0x1000)
[ 10.456951] Get Index(2-GPIO_BASE) phy_addr(0x11d00000) vir_addr=(0xffffffc010aef000) size=(0x1000)
[ 10.465984] Get Index(3-IOCFG_TR_BASE) phy_addr(0x11f00000) vir_addr=(0xffffffc010af1000) size=(0x1000)
[ 10.475368] Get Index(4-IOCFG_TL_BASE) phy_addr(0x11f10000) vir_addr=(0xffffffc010af3000) size=(0x1000)
[ 10.484752] Get Index(5-INFRACFG_AO_BASE) phy_addr(0x10003000) vir_addr=(0xffffffc010af5000) size=(0x1000)
[ 10.494393] Get Index(6-CONN_INFRA_CFG_BASE) phy_addr(0x18001000) vir_addr=(0xffffffc010afd000) size=(0x1000)
[ 10.504293] Get Index(7-CONN_INFRA_SYSRAM_BASE) phy_addr(0x18050000) vir_addr=(0xffffffc010aff000) size=(0x1000)
[ 10.514453] Get Index(8-CONN_INFRA_CLKGEN_ON_TOP_BASE) phy_addr(0x18009000) vir_addr=(0xffffffc010b01000) size=(0x1000)
[ 10.525220] Get Index(9-CONN_HOST_CSR_TOP_BASE) phy_addr(0x18060000) vir_addr=(0xffffffc010b03000) size=(0x1000)
[ 10.535380] Get Index(10-CONN_INFRA_BUS_CR_BASE) phy_addr(0x1800e000) vir_addr=(0xffffffc010b05000) size=(0x1000)
[ 10.545626] Get Index(11-CONN_INFRA_RGU_BASE) phy_addr(0x18000000) vir_addr=(0xffffffc010b79000) size=(0x1000)
[ 10.555613] Get Index(12-CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18005000) vir_addr=(0xffffffc010b7b000) size=(0x1000)
[ 10.566033] Get Index(13-INST2_CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18085000) vir_addr=(0xffffffc010b7d000) size=(0x1000)
[ 10.576975] Get Index(14-CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18004000) vir_addr=(0xffffffc010b7f000) size=(0x1000)
[ 10.587575] Get Index(15-INST2_CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18084000) vir_addr=(0xffffffc010b81000) size=(0x1000)
f[ 10.598518] Get Index(16-CONN_SEMAPHORE_BASE) phy_addr(0x18070000) vir_addr=(0xffffffc010b90000) size=(0x10000)
[ 10.608677] Get Index(17-CONN_AFE_CTL_BASE) phy_addr(0x18003000) vir_addr=(0xffffffc010b83000) size=(0x1000)
[ 10.618491] Get Index(18-CONN_AFE_CTL_2ND_BASE) phy_addr(0x18083000) vir_addr=(0xffffffc010b85000) size=(0x1000)
[ 10.628652] Get Index(19-WF_TOP_SLPPROT_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010bb0000) size=(0x10000)
[ 10.638986] Get Index(20-WF_TOP_CFG_BASE) phy_addr(0x184b0000) vir_addr=(0xffffffc010b8d000) size=(0x1000)
[ 10.648627] Get Index(21-WF_MCU_CONFIG_LS_BASE) phy_addr(0x184f0000) vir_addr=(0xffffffc010ba1000) size=(0x1000)
[ 10.658790] Get Index(22-WF_MCU_BUS_CR_BASE) phy_addr(0x18400000) vir_addr=(0xffffffc010ba3000) size=(0x1000)
[ 10.668690] Get Index(23-WF_MCUSYS_INFRA_BUS_FULL_U_DEBUG_CTRL_AO_BASE) phy_addr(0x18500000) vir_addr=(0xffffffc010ba5000) size=(0x1000)
[ 10.681103] Get Index(24-WF_TOP_CFG_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010bd0000) size=(0x10000)
[ 10.691090] conninfra@(consys_plt_hw_init:162) adie_cfg_type = 1, one_adie_dbdc = 1
[ 10.698740] [emi_mng_init] gConEmiPhyBase = [0x47c80000] size = [0x100000] fw size = [0x100000] ops=[00000000d0374745]
[ 10.709519] conninfra@(mtk_conninfra_drv_init:650) After platform_driver_register
[ 10.717365] ConnInfra Dev: init (0)
[ 10.722283] conninfra@(_consys_polling_chipid_int:306) Read CONNSYS HW IP version successfully! (0x02090000)
[ 10.732126] conninfra@(connsys_d_die_cfg:365) D-die efuse: 0x00000000
f[ 10.739603] conninfra@(_connsys_a_die_cfg_7976:919) adie_idx[0], A-die CHIP ID = 0x7976, HW Version = 0x8a10
[ 10.750427] conninfra@(consys_spi_write_nolock:501) addr=0x0a00, val=0xffffffff
[ 10.758731] conninfra@(consys_spi_write_nolock:501) addr=0x04ac, val=0x0000001c
[ 10.767035] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x00000002
[ 10.776346] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x00000000
[ 10.785659] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x43a60000
[ 10.798003] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x00000001, 0x00c40000, 0x008800b6, 0x00000000]
[ 10.809517] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x00000002
[ 10.818834] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x23a6003a
[ 10.828145] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x63a7003a
[ 10.841487] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x00000001, 0x00c40000, 0x008800b6, 0x00000000]
[ 10.852999] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x00000002
[ 10.862310] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x23a7003a
[ 10.871621] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x63ac003a
[ 10.884960] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x00000001, 0x00c40000, 0x008800b6, 0x00000000]
[ 10.896479] conninfra@(consys_spi_write_nolock:501) addr=0x0038, val=0x4a563b00
[ 10.904784] conninfra@(consys_spi_write_nolock:501) addr=0x065c, val=0x1d59080f
[ 10.913086] conninfra@(consys_spi_write_nolock:501) addr=0x0664, val=0x34c00fe0
[ 10.921391] conninfra@(consys_spi_write_nolock:501) addr=0x0070, val=0x88888005
f[ 10.930658] conninfra@(consys_spi_write_nolock:501) addr=0x0070, val=0x00000005
[ 10.938893] conninfra@(_consys_polling_chipid_int:306) Read CONNSYS HW IP version successfully! (0x02090000)
[ 10.948712] conninfra@(_consys_hw_conninfra_wakeup:470) conninfra_wakeup refcnt=[0]->[1] wakeup!!
[ 10.957749] conninfra@(_consys_hw_conninfra_sleep:490) conninfra_sleep refcnt=[1]->[0] sleep!!
[ 10.966349] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0] FM=[0] GPS=[0] WF=[0] CONNINFRA=[1]
[ 10.979056] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.986254] ehci-fsl: Freescale EHCI Host controller driver
[ 10.992564] ehci-platform: EHCI generic platform driver
[ 10.999405] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 11.006203] ohci-platform: OHCI generic platform driver
[ 11.014968] mediatek_soc_hnat 15100000.hnat: wan = eth1
[ 11.020223] mediatek_soc_hnat 15100000.hnat: lan = eth0
[ 11.025453] mediatek_soc_hnat 15100000.hnat: ppd = eth0
[ 11.030673] mediatek_soc_hnat 15100000.hnat: gmac num = 2
[ 11.036067] mediatek_soc_hnat 15100000.hnat: ppe num = 1
[ 11.041814] mediatek_soc_hnat 15100000.hnat: PPE0 entry number = 8192
[ 11.058625] mediatek_soc_hnat 15100000.hnat: PPE0 hwnat start
f[ 11.064445] hnat roaming work enable
[ 11.071102] warp_module_init(): module init and register callback for warp
[ 11.078028] create warp_ctrl ok!!!
[ 11.081464] wed_get_slot_map(): assign slot_id:0 for entry: 0!
[ 11.087301] wed_get_slot_map(): assign slot_id:1 for entry: 1!
[ 11.093702] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 11.111184] init: - preinit -
f[ 11.352659] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 11.361014] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- failsafe -
/etc/preinit: line 6: /sbin/mtk_failsafe.sh: not found
f
BusyBox v1.33.2 (2023-04-26 13:00:20 UTC) built-in shell (ash)
ash: can't access tty; job control turned off
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 21.02-SNAPSHOT, r0-0e8a77c2
-----------------------------------------------------
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
https://openwrt.org/docs/guide-user/troubleshooting/
- failsafe_and_factory_reset
- root_password_reset
=======================================================
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/#
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# fff
ash: fff: not found
CMCCAdmin@(none):/# f
ash: f: not found
CMCCAdmin@(none):/# fw_setenv bootmenu_delay 3
Cannot parse config file '/etc/fw_env.config': No such file or directory
Error: environment not initialized
CMCCAdmin@(none):/# mount_root
[ 42.603832] mount_root: loading kmods from internal overlay
[ 42.620824] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 42.629335] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 43.651267] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 43.672616] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 842
[ 43.697755] UBIFS (ubi0:2): recovery needed
[ 43.772646] UBIFS (ubi0:2): recovery completed
[ 43.777175] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 43.785004] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 43.794915] UBIFS (ubi0:2): FS size: 41521152 bytes (39 MiB, 327 LEBs), journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 43.805340] UBIFS (ubi0:2): reserved for root: 1961146 bytes (1915 KiB)
[ 43.811949] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 2C47F697-BBAD-403A-8722-5C2EF1D46952, small LPT model
[ 43.824382] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 43.835345] block: extroot: not configured
[ 43.839574] UBIFS (ubi0:2): un-mount UBI device 0
[ 43.844287] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[ 43.853245] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 43.858979] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 845
[ 43.926144] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 43.933983] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 43.943884] UBIFS (ubi0:2): FS size: 41521152 bytes (39 MiB, 327 LEBs), journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 43.954304] UBIFS (ubi0:2): reserved for root: 1961146 bytes (1915 KiB)
[ 43.960909] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 2C47F697-BBAD-403A-8722-5C2EF1D46952, small LPT model
[ 43.976296] mount_root: loading kmods from internal overlay
[ 43.992558] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 44.001968] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 44.954244] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 44.964387] block: extroot: not configured
[ 44.970118] mount_root: switching to ubifs overlay
CMCCAdmin@(none):/# sed -i 's/.*local debug=.*/\tlocal debug=1/' /etc/init.d/tel
net
sed: /etc/init.d/telnet: No such file or directory
CMCCAdmin@(none):/# passwd root
passwd: unknown user root
CMCCAdmin@(none):/# passwd
passwd: no record of CMCCAdmin in /etc/shadow, using /etc/passwd
Changing password for CMCCAdmin
New password:
Bad password: too weak
Retype password:
passwd: password for CMCCAdmin changed by CMCCAdmin
CMCCAdmin@(none):/#
以上是代码，又翻看了本论坛其他先行者的刷机帖子，又试了几次，和他们一样失败。
请看图
也不知道哪里错了，请大神指导一下。感谢！
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？立即注册
×
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡