|
|
楼主 |
发表于 2012-7-14 22:31
|
显示全部楼层
附上我用超级终端操作时的信息：
U-Boot 1.1.3 (Sep 30 2009 - 21:47:05)
Board: Ralink APSoC DRAM: 16 MB
relocate_code Pointer at: 80fb4000
spi_wait_nsec: 3e
spi deice id: c2 20 16 c2 20 (2016c220)
find flash: mx25l3205d
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.3
--------------------------------------------
ASIC 3052_MP2 (Port5<->Phy)
DRAM component: 128 Mbits SDR
DRAM bus: 16 bit
Total memory: 16 MBytes
Flash component: SPI Flash
Date:Sep 30 2009 Time:21:47:05
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 320 MHZ ####
SDRAM bus set to 16 bit
SDRAM size =16 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 3
0
3: System Boot system code via Flash.
## Booting image at bf050000 ...
raspi_read: from:50000 len:40
Image Name: Linux Kernel Image
Created: 2010-12-13 6:41:15 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 3493824 Bytes = 3.3 MB
Load Address: 80000000
Entry Point: 8023a000
raspi_read: from:50040 len:354fc0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8023a000) ...
## Giving linux memsize in MB, 16
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.21 (jason@CompilerServer.gemtek.com.tw) (gcc version
3.4.2) #5
61 Mon Dec 13 14:40:42 CST 2010
The CPU feqenuce set to 320 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists. Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=1f04
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32
bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 2080000c, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 00138800(1280000)
CPU frequency 320.00 MHz
Using 160.000 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13760k/16384k available (2011k kernel code, 2624k reserved,
264k data, 1
08k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
Load Ralink DFS Timer Module
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Ralink APSoC Hardware Watchdog Timer
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing
disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 254
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
flash0: started
block2mtd: version $Revision: 1.1.1.1 $
deice id : c2 20 16 c2 20 (2016c220)
mx25l3205d(c2 20160000) (4096 Kbytes)
mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000
(64K) .numera
seregions = 0
Creating 6 MTD partitions on "raspi":
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x00140000 : "Kernel"
0x00140000-0x003b0000 : "RootFS"
0x003b0000-0x00400000 : "User_CFG"
nf_conntrack version 0.5.0 (128 buckets, 1024 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00 256 rx/tx
descriptors allocat
ed, mtu = 1500!
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 108k freed
init started: BusyBox v1.12.1 (2010-12-13 14:28:34 CST)
starting pid 11, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
mount: mounting devpts: called with bogus options
none on /sys failed: No such device
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
=System Architecture Department=
[check_jffs]80 : JFFS_OK
Set: phy[0].reg[0] = 3100
Set: phy[1].reg[0] = 3100
Set: phy[2].reg[0] = 3100
Set: phy[3].reg[0] = 3100
Set: phy[4].reg[0] = 3100
nvram_init: INFO=>nvram MAC initialized successfully!
==>shm_init()!!
check_shm_hash: Check shm hash value
nvram_init: INFO=>nvram conf initialized successfully!
nvram_init: INFO=> RAM CONF successful created!
nvram_init: INFO=> RC.CONF successful created!
GDMA1_MAC_ADRH -- : 0x0000106f
GDMA1_MAC_ADRL -- : 0x3f422280
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
phy_tx_ring = 0x00833000, tx_ring = 0xa0833000
phy_rx_ring = 0x00000000, rx_ring = 0x00000000
RT305x_ESW: Link Status Changed
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 710000
vlan0001: Setting MAC address to 10 6f 3f 42 22 80.
VLAN (vlan0001): Underlying device (eth2) has same MAC, not checking
promisciou
s mode.
vlan0002: Setting MAC address to 10 6f 3f 42 22 80.
VLAN (vlan0002): Underlying device (eth2) has same MAC, not checking
promisciou
s mode.
vlan0001: dev_set_promiscuity(master, 1)
device eth2 entered promiscuous mode
device vlan0001 entered promiscuous mode
br0: port 1(vlan0001) entering learning state
Fri Jan 1 00:00:00 GMT 2010
Started WatchDog Timer.
br0: topology change detected, propagating
br0: port 1(vlan0001) entering forwarding state
rt2860v2_ap: module license 'unspecified' taints kernel.
=== pAd = c0072000, size = 494272 ===
<-- RTMPAllocAdapterBlock, Status=0
RX DESC a0adf000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff 00 00 00 00
RT305x_ESW: Link Status Changed
RT305x_ESW: Link Status Changed
Main bssid = 10:6f:3f:42:22:80
<==== rt28xx_init, Status=0
0x1300 = 00064380
device ra4 entered promiscuous mode
br0: port 2(ra4) entering learning state
device ra0 entered promiscuous mode
br0: port 3(ra0) entering learning state
brctl setwlanforward br0 15
ipv6 pass through init OK
libupnp: using UDP SSDP_PORT = 1900
ipv6_passthru_disable
ipv6_passthru_disable
br0: topology change detected, propagating
br0: port 2(ra4) entering forwarding state
br0: topology change detected, propagating
br0: port 3(ra0) entering forwarding state
/usr/shell/dnsmasq.sh stop ok
/usr/shell/dnsmasq.sh start ok
dnsmasq: using nameserver 168.95.1.1#53
/usr/shell/udhcpd.sh config ok
/usr/shell/udhcpd.sh start ok
***** g_wl_interface = ra0 ******
MAX_NUM_SESSIONS : 5; NUM_SEES: 64
starting pid 773, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2010-12-13 14:28:34 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
|
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2012-7-14 22:29
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
