找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 7322|回复: 10

ASUS RT N12-B1 刷最新固件后没有无线怎么破?

[复制链接]
如题 ,ASUS RT N12-B1 刷https://downloads.openwrt.org/ch ... n12-b1-squashfs.trx固件后,没有无线了。同时也无法更新软包。

现在论坛怎么了,上不了图片?表情也加不了?附件都不可以了?

刷机后的启动信息如下:
>>>CFE version 5.100.138.9 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
>>>Build Date: ?  1る 17 16:59:52 CST 2012 (root@myvm1110hdd-vm)
>>>Copyright (C) 2000-2008 Broadcom Corporation.
>>>
>>>Init Arena
>>>Init Devs.
>>>Boot partition size = 131072(0x20000)
>>>Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
>>>et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.9
>>>CPU type 0x19749: 300MHz
>>>Tot mem: 32768 KBytes
>>>
>>>CFE mem:    0x80700000 - 0x80799720 (628512)
>>>Data:       0x8072F560 - 0x80732790 (12848)
>>>BSS:        0x80732790 - 0x80733720 (3984)
>>>Heap:       0x80733720 - 0x80797720 (409600)
>>>Stack:      0x80797720 - 0x80799720 (8192)
>>>Text:       0x80700000 - 0x8072F560 (193888)
>>>
>>>Device eth0:  hwaddr 30-85-A9-8A-70-C0, ipaddr 192.168.1.1, mask 255.255.255.0
>>>        gateway not set, nameserver not set
>>>end of nvram_rescuegpio_init
>>>Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
>>>Loading: CFE works as TFTP Server.
>>>Failed.
>>>Could not load :: Timeout occured
>>>Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
>>>Loading: .. 3712 bytes read
>>>Entry at 0x80001000
>>>Closing network.
>>>Starting program at 0x80001000
>>>   0.000000] Linux version 3.18.20 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46450) ) #1 Fri Sep 4 15:10:42 CEST 2015
>>>[    0.000000] CPU0 revision is: 00019749 (MIPS 74Kc)
>>>[    0.000000] bcm47xx: Using bcma bus
>>>[    0.000000] bcma: bus0: Found chip with id 53572, rev 0x01 and package 0x08
>>>[    0.000000] Determined physical RAM map:
>>>[    0.000000]  memory: 02000000 @ 00000000 (usable)
>>>[    0.000000] Initrd not found or empty - disabling initrd
>>>[    0.000000] Zone ranges:
>>>[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
>>>[    0.000000]   HighMem  empty
>>>[    0.000000] Movable zone start for each node
>>>[    0.000000] Early memory node ranges
>>>[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
>>>[    0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
>>>[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
>>>[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
>>>[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
>>>[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
>>>[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
>>>[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
>>>[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
>>>[    0.000000] Writing ErrCtl register=00000000
>>>[    0.000000] Readback ErrCtl register=00000000
>>>[    0.000000] Memory: 28840K/32768K available (2637K kernel code, 113K rwdata, 328K rodata, 172K init, 288K bss, 3928K reserved, 0K highmem)
>>>[    0.000000] NR_IRQS:128
>>>[    0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0)
>>>[    0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1C, class 0x0)
>>>[    0.000000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x03, class 0x0)
>>>[    0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x05, class 0x0)
>>>[    0.000000] bcma: bus0: Core 4 found: SDR/DDR1 Memory Controller (manuf 0x4BF, id 0x835, rev 0x02, class 0x0)
>>>[    0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0x10000, blocks: 128)
>>>[    0.000000] bcma: bus0: Early bus registered
>>>[    0.000000] MIPS: machine is Asus RT-N12B1
>>>[    0.000000] bcm47xx: Setting up vectored interrupts
>>>[    0.070000] Calibrating delay loop... 149.91 BogoMIPS (lpj=749568)
>>>[    0.070000] pid_max: default: 32768 minimum: 301
>>>[    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
>>>[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
>>>[    0.070000] NET: Registered protocol family 16
>>>[    0.100000] Switched to clocksource MIPS
>>>[    0.100000] NET: Registered protocol family 2
>>>[    0.100000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
>>>[    0.100000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
>>>[    0.100000] TCP: Hash tables configured (established 1024 bind 1024)
>>>[    0.100000] TCP: reno registered
>>>[    0.100000] UDP hash table entries: 256 (order: 0, 4096 bytes)
>>>[    0.100000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
>>>[    0.110000] NET: Registered protocol family 1
>>>[    0.440000] bcma: bus0: Bus registered
>>>[    0.450000] futex hash table entries: 256 (order: -1, 3072 bytes)
>>>[    0.450000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
>>>[    0.450000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
>>>[    0.450000] msgmni has been set to 56
>>>[    0.450000] io scheduler noop registered
>>>[    0.450000] io scheduler deadline registered (default)
>>>[    0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
>>>[    0.460000] console [ttyS0] disabled
>>>[    0.480000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250000) is a U6_16550A
>>>[    0.820000] console [ttyS0] enabled
>>>[    1.000000] 6 bcm47xxpart partitions found on MTD device bcm47xxsflash
>>>[    1.000000] Creating 6 MTD partitions on "bcm47xxsflash":
>>>[    1.010000] 0x000000000000-0x000000020000 : "boot"
>>>[    1.020000] 0x000000020000-0x0000007f0000 : "firmware"
>>>[    1.020000] 0x00000002001c-0x00000002090c : "loader"
>>>[    1.030000] 0x00000002090c-0x00000012b400 : "linux"
>>>[    1.040000] 0x00000012b400-0x0000007f0000 : "rootfs"
>>>[    1.050000] mtd: device 4 (rootfs) set to be root filesystem
>>>[    1.050000] 1 squashfs-split partitions found on MTD device rootfs
>>>[    1.060000] 0x000000350000-0x0000007f0000 : "rootfs_data"
>>>[    1.060000] 0x0000007f0000-0x000000800000 : "nvram"
>>>[    1.070000] bgmac bcma0:2: Found PHY addr: 30 (NOREGS)
>>>[    1.080000] bgmac bcma0:2: Support for Roboswitch not implemented
>>>[    1.130000] libphy: bgmac mii bus: probed
>>>[    1.240000] b53_common: found switch: BCM5325, rev 4
>>>[    1.240000] bgmac: Broadcom 47xx GBit MAC driver loaded
>>>[    1.250000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
>>>[    1.260000] TCP: cubic registered
>>>[    1.260000] NET: Registered protocol family 17
>>>[    1.270000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
>>>[    1.280000] Bridge firewalling registered
>>>[    1.280000] 8021q: 802.1Q VLAN Support v1.8
>>>[    1.300000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
>>>[    1.310000] Freeing unused kernel memory: 172K (80305000 - 80330000)
>>>[    3.660000] init: Console is alive
>>>[    3.660000] init: - watchdog -
>>>[    5.790000] init: - preinit -
>>>[    6.800000] random: mktemp urandom read with 10 bits of entropy available
>>>ress the [f] key and hit [enter] to enter failsafe mode
>>>ress the [1], [2], [3] or [4] key and hit [enter] to select the debug level
>>>[   10.480000] jffs2: notice: (222) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
>>>[   10.500000] mount_root: switching to jffs2 overlay
>>>[   10.570000] procd: - early -
>>>[   10.570000] procd: - watchdog -
>>>[   11.730000] procd: - ubus -
>>>[   12.740000] procd: - init -
>>>lease press Enter to activate this console.
>>>[   15.930000] NET: Registered protocol family 10
>>>[   15.950000] ip6_tables: (C) 2000-2006 Netfilter Core Team
>>>[   15.980000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
>>>[   15.990000] Backport generated by backports.git backports-20150129-0-gdd4a670
>>>[   16.000000] ip_tables: (C) 2000-2006 Netfilter Core Team
>>>[   16.030000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
>>>[   16.110000] xt_time: kernel timezone is -0000
>>>[   16.170000] cfg80211: Calling CRDA to update world regulatory domain
>>>[   16.170000] cfg80211: World regulatory domain updated:
>>>[   16.180000] cfg80211:  DFS Master region: unset
>>>[   16.180000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
>>>[   16.190000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
>>>[   16.200000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
>>>[   16.210000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
>>>[   16.220000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
>>>[   16.220000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
>>>[   16.230000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
>>>[   16.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
>>>[   16.250000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
>>>[   16.410000] PPP generic driver version 2.4.2
>>>[   16.420000] NET: Registered protocol family 24
>>>[   16.460000] b43-phy0: Broadcom 53572 WLAN found (core revision 28)
>>>[   16.470000] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 17
>>>[   16.480000] b43-phy0 ERROR: FOUND UNSUPPORTED RADIO (Manuf 0x17F, ID 0x2057, Revision 13, Version 0)
>>>[   16.490000] b43: probe of bcma0:1 failed with error -122
>>>[   16.490000] Broadcom 43xx driver loaded [ Features: NL ]
>>>[   32.370000] device eth0.1 entered promiscuous mode
>>>[   32.380000] device eth0 entered promiscuous mode
>>>[   32.390000] br-lan: port 1(eth0.1) entered forwarding state
>>>[   32.390000] br-lan: port 1(eth0.1) entered forwarding state
>>>[   34.390000] br-lan: port 1(eth0.1) entered forwarding state
>>>[   75.180000] random: nonblocking pool is initialized


哪位高手帮忙看看怎么搞?


哪位高手帮忙看看怎么搞?
来自手机 | 显示全部楼层
博通芯片本来就没无线  这很正常 5357还是刷其他的固件吧 玩openwrt还是ar 或者 mtk好 固件多!!
回复

使用道具 举报

 楼主| | 显示全部楼层
x1060703191 发表于 2016-5-15 17:53
博通芯片本来就没无线  这很正常 5357还是刷其他的固件吧 玩openwrt还是ar 或者 mtk好 固件多!!

谢谢!
回复

使用道具 举报

 楼主| | 显示全部楼层
x1060703191 发表于 2016-5-15 17:53
博通芯片本来就没无线  这很正常 5357还是刷其他的固件吧 玩openwrt还是ar 或者 mtk好 固件多!!

为死心的我,又看看了看是带无线的呀!有图有真相


本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
回复

使用道具 举报

来自手机 | 显示全部楼层
lms8653 发表于 2016-5-19 13:29
为死心的我,又看看了看是带无线的呀!有图有真相

既然是5357B0 你刷openwrt只是为了多播ss的话刷tomato dualwan 更为稳定 5357B0有dualwan固件!!
回复

使用道具 举报

 楼主| | 显示全部楼层
x1060703191 发表于 2016-5-19 14:53
既然是5357B0 你刷openwrt只是为了多播ss的话刷tomato dualwan 更为稳定 5357B0有dualwan固件!!

谢谢,求科普,大神SS是什么?
回复

使用道具 举报

来自手机 | 显示全部楼层
lms8653 发表于 2016-5-20 11:10
谢谢,求科普,大神SS是什么?

兲朝上网……………  外面的世界很精彩 ………     你的5357b0有专用的dualwan固件 去找找 貌似只能刷那个但是很好用  多拨最好了
回复

使用道具 举报

 楼主| | 显示全部楼层
x1060703191 发表于 2016-5-20 11:33
兲朝上网……………  外面的世界很精彩 ………     你的5357b0有专用的dualwan固件 去找找 貌似只能刷那 ...

好的,多谢
回复

使用道具 举报

我的也是没有无线,53572的CPU 刷不了 DUALWAN
回复

使用道具 举报

出了N12B1的固件,就不能完整的出吗?
回复

使用道具 举报

这个openwrt是编程器固件吗?
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-5-10 01:24

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表