商务领航贝尔RG100E-CA TTL显示信息

安顺电***

这一款配置：CPU：300M
                     内存：32M

[CFE][boot][ST Serial flash offset 00000000 size 128KB]
[CFE][trx0][ST Serial flash offset 00020000 size 1KB]
[CFE][os0][ST Serial flash offset 0002001C size 8832KB]
[CFE][trx1][ST Serial flash offset 008C0000 size 1KB]
[CFE][os1][ST Serial flash offset 008C001C size 7392KB]
[CFE][nvram][ST Serial flash offset 00FF8000 size 32KB]
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.120.9
CPU type 0x19749: 300MHz
Tot mem: 32768 KBytes
CFE mem:    0x80700000 - 0x8079A640 (632384)
Data:       0x80730540 - 0x807336C0 (12672)
BSS:        0x807336C0 - 0x80734640 (3968)
Heap:       0x80734640 - 0x80798640 (409600)
Stack:      0x80798640 - 0x8079A640 (8192)
Text:       0x80700000 - 0x80730534 (197940)
Device eth0:  hwaddr AC-6E-1A-09-53-40, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
cur=
buf=go;
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: Failed.
Could not load :: Timeout occured
Boot from big image !!
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ...... 3352608 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.21.5 (root@localhost) (gcc version 4.2.3) #1 Fri Jun 29 13:55:20 CST 2012
Found a 16MB ST compatible serial flash
Serial flash device: name SFLASH 16384 kB, id 0x0000 size 16384KB
prom init
CPU revision is: 00019749
######## NVRAM INFO ###########
backupPsi:1
wpsDevicePin:1234567
PsiSize:64
SyslogSize:48
ucAuxFSPercent:25
productClass:RG100E-CA
wlSsid:ChinaNet-phLj
wl_wpapsk:kxutuchc
user_pass:waib5
deviceId:47900AC6E1A095340
startFlag:1
factoryData:1
######## NVRAM INFO END ########
Total Flash size: 16384K with 256 sectors
Flash split 25 : AuxFS[4194304]
Blk# BlkOff Blks  MemLen Partition Name
255      0    1   32768 NVRAM
252      0    1   65536 Factory Data
251      0    1   65536 Backup PSI
253      0    1   49152 Syslog
253  57344    1    8192 Scratch PAD
254      0    1   65536 PSI
187      0   64 4194304 JFFS_AUXFS
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 32 pages used for memmap
  Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists.  Total pages: 8128
Kernel command line: root=31:2 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
CPU: BCM5357 rev 2 at 300 MHz
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28932k/32768k available (2522k kernel code, 3836k reserved, 645k data, 104k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80c00000 ... 0x80d00000>
Calibrating delay loop... 297.98 BogoMIPS (lpj=148992)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: no core
PCI: Fixing up bus 0
BLOG v2.1 Initialized
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
鉫rial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
IMQ starting with 2 devices...
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
pflash: found no supported devices
cur_part=0, sAddr=9c020000, mAddr=9c8b0000
Found TRX Magic :0x30524448
sflash: squash filesystem with lzma found at block 1429
Creating 9 MTD partitions on "sflash":
0x00000000-0x00020000 : "boot"
0x00020000-0x00bb0000 : "linux"
0x001654a0-0x00bb0000 : "rootfs"
0x00bb0000-0x00fb0000 : "auxfs"
0x00fb0000-0x00fc0000 : "log"
0x00fc0000-0x00fd0000 : "backpsi"
0x00fd0000-0x00fe0000 : "sp"
0x00fe0000-0x00ff0000 : "psi"
0x00ff0000-0x01000000 : "nvram"
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
brcmboard: brcm_board_init entry
Mirror/redirect action on
u32 classifier
    input device check on
    Actions configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 104k freed
init started:  BusyBox v1.00 (2012.06.29-05:58+0000) multi-call binary

安顺电***

BusyBox v1.00 (2012.06.29-05:58+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Decompressing...done


CFE version 5.60.120.9  based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Wed Jun 29 17:55:17 CST 2011 (root@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found a 16MB ST compatible serial flash
[CFE][boot][ST Serial flash offset 00000000 size 128KB]
[CFE][trx][ST Serial flash offset 00020000 size 1KB]
[CFE][os][ST Serial flash offset 0002001C size 16224KB]
[CFE][nvram][ST Serial flash offset 00FF8000 size 32KB]
[CFE][boot][ST Serial flash offset 00000000 size 128KB]
[CFE][trx0][ST Serial flash offset 00020000 size 1KB]
[CFE][os0][ST Serial flash offset 0002001C size 8832KB]
[CFE][trx1][ST Serial flash offset 008C0000 size 1KB]
[CFE][os1][ST Serial flash offset 008C001C size 7392KB]
[CFE][nvram][ST Serial flash offset 00FF8000 size 32KB]
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.120.9
CPU type 0x19749: 300MHz
Tot mem: 32768 KBytes

CFE mem:    0x80700000 - 0x8079A640 (632384)
Data:       0x80730540 - 0x807336C0 (12672)
BSS:        0x807336C0 - 0x80734640 (3968)
Heap:       0x80734640 - 0x80798640 (409600)
Stack:      0x80798640 - 0x8079A640 (8192)
Text:       0x80700000 - 0x80730534 (197940)

Device eth0:  hwaddr AC-6E-1A-09-53-40, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
cur=
buf=go;
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: Failed.
Could not load :: Timeout occured
Boot from big image !!
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ...... 3352608 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.21.5 (root@localhost) (gcc version 4.2.3) #1 Fri Jun 29 13:55:20 CST 2012
Found a 16MB ST compatible serial flash
Serial flash device: name SFLASH 16384 kB, id 0x0000 size 16384KB
prom init
CPU revision is: 00019749
######## NVRAM INFO ###########
backupPsi:1
wpsDevicePin:1234567
PsiSize:64
SyslogSize:48
ucAuxFSPercent:25
productClass:RG100E-CA
wlSsid:ChinaNet-phLj
wl_wpapsk:kxutuchc
user_pass:waib5
deviceId:47900AC6E1A095340
startFlag:1
factoryData:1
######## NVRAM INFO END ########
Total Flash size: 16384K with 256 sectors
Flash split 25 : AuxFS[4194304]
Blk# BlkOff Blks  MemLen Partition Name
255      0    1   32768 NVRAM
252      0    1   65536 Factory Data
251      0    1   65536 Backup PSI
253      0    1   49152 Syslog
253  57344    1    8192 Scratch PAD
254      0    1   65536 PSI
187      0   64 4194304 JFFS_AUXFS
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 32 pages used for memmap
  Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists.  Total pages: 8128
Kernel command line: root=31:2 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
CPU: BCM5357 rev 2 at 300 MHz
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28932k/32768k available (2522k kernel code, 3836k reserved, 645k data, 104k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80c00000 ... 0x80d00000>
Calibrating delay loop... 297.98 BogoMIPS (lpj=148992)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: no core
PCI: Fixing up bus 0
BLOG v2.1 Initialized
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
IMQ starting with 2 devices...
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
pflash: found no supported devices
cur_part=0, sAddr=9c020000, mAddr=9c8b0000
Found TRX Magic :0x30524448
sflash: squash filesystem with lzma found at block 1429
Creating 9 MTD partitions on "sflash":
0x00000000-0x00020000 : "boot"
0x00020000-0x00bb0000 : "linux"
0x001654a0-0x00bb0000 : "rootfs"
0x00bb0000-0x00fb0000 : "auxfs"
0x00fb0000-0x00fc0000 : "log"
0x00fc0000-0x00fd0000 : "backpsi"
0x00fd0000-0x00fe0000 : "sp"
0x00fe0000-0x00ff0000 : "psi"
0x00ff0000-0x01000000 : "nvram"
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
brcmboard: brcm_board_init entry
Mirror/redirect action on

安顺电***

u32 classifier
    input device check on
    Actions configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 104k freed
init started:  BusyBox v1.00 (2012.06.29-05:58+0000) multi-call binary


BusyBox v1.00 (2012.06.29-05:58+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

[167 3g-mngr-msg.c:490 diald_3g()]:Create diald monitor process with pid of 167.
pktflow: module license 'Proprietary' taints kernel.
size of sk_buff is different. fc  212, kernel 212!!
size of nf_conn is different. fc  244, kernel  244!!
size of net_device is different. fc 792 kernel 792!!
Broadcom Packet Flow Cache  Char Driver v2.1 Apr 26 2012 11:05:34 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Apr 26 2012 11:54:15
Broadcom BCMPROCFS v1.0 initialized
PCI: Setting latency timer of device 0000:00:02.0 to 64
bcmsw: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.120.9
eth0: MAC Address: AC:6E:1A:09:53:40
eth1: MAC Address: AC:6E:1A:09:53:40
eth2: MAC Address: AC:6E:1A:09:53:40
eth3: MAC Address: AC:6E:1A:09:53:40
eth4: MAC Address: AC:6E:1A:09:53:40
KLOB extended to 2 pools
eth4 Link UP 100 mbps full duplex
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl0: Broadcom BCM4329 802.11 Wireless Controller 5.60.120.9  (WLTEST)

===== Release Version 4.02L.03.wp1 (build timestamp 120629_1355) =====

KLOB extended to 3 pools
drivers/usb/serial/usb-serial.c: USB Serial support registered for 3G_USB_modem
[USB MODEM SERIAL modem_usb_init:374] usb_serial_register(3g_modem) success
usbcore: registered new interface driver 3g_modem
[USB MODEM SERIAL modem_usb_init:385] usb_register(3g_modem) success
######### Load CMS_CONFIG_PRIMARY #########
insmod: cannot insert `/lib/modules/2.6.21.5/extra/pktflow.ko': Success (17): Success
ssk:error:15.184:rcl_timeServerCfgObject:43:Add or enable sntp entry: enable = 1, server1=clock.fmt.he.net, server2=(null), server3=(null), server4=(null), server5=(null), currTime=(null), zoneTime=(null), zoneName=Pacific time, Tijuana, dsu=0, dss=2000-01-01T00:06:46+00:00, dse=2000-01-01T00:06:46+00:00
rutSntp_isAllRequiredValuesPresent--tzname=Pacific time, Tijuana--ntp=clock.fmt.he.net--
ssk:error:16.330:rutPMap_associateWanIntfWithBridge:243:could not find network obj of InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1, ret=9804
ssk:error:16.330:rcl_l2BridgingFilterObject:239:could not associate wan intf with bridge, ret=9804
ssk:error:16.330:mdm_activateObjects:1115:rcl handler reports error=9804 on Filter {9}
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_queue: failed to register queue handler
insmod: cannot insert `/lib/modules/2.6.21.5/kernel/net/ipv4/netfilter/ip_queue.ko': Success (16): Success
ip6_tables: (C) 2000-2006 Netfilter Core Team
set a mode, mode=0
iptables: Bad rule (does a matching rule exist in that chain?)
device eth1 is not a slave of br0
device eth1 entered promiscuous mode
br0: port 1(eth1) entering learning state
br0: topology change detected, propagating
br0: port 1(eth1) entering forwarding state
device eth2 is not a slave of br0
device eth2 entered promiscuous mode
br0: port 2(eth2) entering learning state
br0: topology change detected, propagating
br0: port 2(eth2) entering forwarding state
device eth3 is not a slave of br0
device eth3 entered promiscuous mode
br0: port 3(eth3) entering learning state
br0: topology change detected, propagating
br0: port 3(eth3) entering forwarding state
device eth4 is not a slave of br0
device eth4 entered promiscuous mode
br0: port 4(eth4) entering learning state
br0: topology change detected, propagating
br0: port 4(eth4) entering forwarding state
Sorry, rule does not exist.
Sorry, rule does not exist.
wlctl: wl driver adapter not found
wlctl: wl driver adapter not found
wlctl: wl driver adapter not found
ssk:error:22.859:rutWan_startInterface:553:Unable to config WAN interface!
ssk:error:22.859:rutCfg_wanPppConnectionSetup:728:rutWan_startInterface failed. error=9002
ssk:error:22.867:mdm_activateObjects:1115:rcl handler reports error=9002 on WANPPPConnection {2,1,1}
set a mode, mode=0
br0: port 4(eth4) entering disabled state
br0: port 3(eth3) entering disabled state
br0: port 2(eth2) entering disabled state
br0: port 1(eth1) entering disabled state
br0: port 4(eth4) entering learning state
br0: port 3(eth3) entering learning state
br0: port 2(eth2) entering learning state
br0: port 1(eth1) entering learning state
br0: topology change detected, propagating
br0: port 4(eth4) entering forwarding state
br0: topology change detected, propagating
br0: port 3(eth3) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth1) entering forwarding state
br0: port 4(eth4) entering disabled state
br0: port 3(eth3) entering disabled state
br0: port 2(eth2) entering disabled state
br0: port 1(eth1) entering disabled state
br0: port 4(eth4) entering learning state
br0: port 3(eth3) entering learning state
br0: port 2(eth2) entering learning state
br0: port 1(eth1) entering learning state
br0: topology change detected, propagating
br0: port 4(eth4) entering forwarding state
br0: topology change detected, propagating
br0: port 3(eth3) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth1) entering forwarding state
Using pin 21 for reset button input
Using pin 20 for wps button input
Using pin 10 for wlan button input
Massive upgrader start up !
image_crc=0x1c52fa6
udp_send finished
tr69c:error:24.257:xdslCtl_Open:91pen error 6
Digital Media Server Version [1.3 Build Jun 29 2012 14:02:32]
Content Dir Path Set To: /mnt
IP: 192.168.1.1

FriendlyName=ChinaNet Digital Media Server
Udn=uuid:727dd440-1dd2-11b2-a618-b2fdf4d2c378
br0: port 1(eth1) entering disabled state
br0: port 2(eth2) entering disabled state
br0: port 3(eth3) entering disabled state
KLOB extended to 4 pools
iptables: No chain/target/match by that name
httpd:error:29.175:readMessageFromSmd:3452:unrecognized msg 0x10000250
WLmngr Daemon is running
optarg=0 shmId=0
WEBUI Operation WPS Type is NONE, interface number is [1]
WEBUI Operation WPS Type is NONE, interface number is [2]
WEBUI Operation WPS Type is NONE, interface number is [3]
WEBUI Operation WPS Type is NONE, interface number is [4]
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
eth0_1: no IPv6 routers present
Setting SSID: "ChinaNet-phLj"
Setting SSID: "ChinaNet-13"
Setting SSID: "ChinaNet-14"
Setting SSID: "ChinaNet-15"
Massive upgrade timeout.
exit without upgrading !
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
chanspec 0x2b0b selected
device wl0 entered promiscuous mode
device wl0.1 entered promiscuous mode
device wl0.2 entered promiscuous mode
device wl0.3 entered promiscuous mode
br0: port 5(wl0) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0) entering forwarding state
32768500 (0x1f401f4)
ifconfig: br1: error fetching interface information: Device not found

=======> BUPnPControlPoint_AddDevice 652        uuid = d2e22eee-a075-94b5-ec78-3dfaed4f3c4c ,  location =http://192.168.1.1:1780/InternetGatewayDevice.xml  
Reaped 1636
UPnP daemon is ready to run
smd:error:41.380:collectApp:1270:bcmmserver (pid 1056) exited due to uncaught signal number 11
wlctl: Unsupported
KLOB extended to 5 pools
<== rut_modifyNumGeneric 346 ==> ancestorOid =114 , decendentOid=115