TP-LINK WDR 5620 V2.0 有可用的BREED么？

maim***

如题，手里有台中国电信定制给的一台TP-LINK WDR 5620  V2.0，千兆版，内存是64M ，flash 8m ，取下flash用编程器刷入几乎十几款 mtk7620的breed（包括7628和7688的breed）之后，路由都不能正常工作，连breed都启动不了。。。后来ttl搞了些数据出来
看哪个大佬有工夫搞下。。。

                                    

我把贴片给改成直插的了，，刷机方便。。。要不我也不会试了十几个BREED。。。。。

8M的  25Q64


TTL 接口，我自己加的针，，，从左到右依次是VCC   GND     TX    RX


2.4G

螃蟹的RTL8367S

MTK7620DA  处理器，集成64M内存


下面是作了中断之后的，有命令，但没玩过，不会。。。。

U-Boot 1.1.3 (Jun 29 2018 - 18:15:44)

Board: Ralink APSoC 64 MB
relocate_code Pointer at: 83fa8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_ns
[15:03:26.287]发→◇slp
□ec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

Press reset button to enter recovery mode.

Autobooting in 500 mseconds

[15:03:26.395]发→◇slp
□
[15:03:26.398]收←◆============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->GigaSW)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jun 29 2018  Time:18:15:44
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes

[15:03:26.504]发→◇slp
□
[15:03:26.508]收←◆---rtl_init_switch--- done
raspi_read: from:40028 len:6

MT7620 #
MT7620 #

MT7620 #
MT7620 #
[15:10:35.823]发→◇help
□
[15:10:35.828]收←◆help
?       - alias for 'help'
bootm   - boot application image from memory
cp      - memory copy
erase   - erase SPI FLASH memory
go      - start application at address 'addr'
help    - print online help
httpd        - start www server for firmware recovery
loadb   - load binary file over serial line (kermit mode)
md      - memory display
mdio   - Ralink PHY register R/W command !!
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
nm      - memory modify (constant address)
printenv- print environment variables
reset   - Perform RESET of the CPU
rf      - read/write rf register
saveenv - save environment variables to persistent storage
setenv  - set environment variables
tftpboot- boot image via network using TFTP protocol
version - print monitor version
MT7620 #





下面是没作中断

U-Boot 1.1.3 (Jun 29 2018 - 18:21:26)

Board: Ralink APSoC 64 MB
relocate_code Pointer at: 83fbc000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:10000 len:1000
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.3.S.0
--------------------------------------------
ASIC 7620_MP (Port5<->GigaSW)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jun 29 2018  Time:18:21:26
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
---rtl_init_switch--- done
raspi_read: from:20028 len:6

Autobooting in 100 mseconds

[11:04:52.773]收←◆## Booting image at bc040000 ...
   Uncompressing Kernel Image ...
[11:04:59.319]收←◆OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

THIS IS ASIC
[    0.000000] Linux version 3.10.14 (jenkins@Sohocilnx1) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Fri Jun 29 18:29:19 CST 2018
[    0.000000]
[    0.000000]  The CPU feqenuce set to 580 MHz
[    0.000000]  PCIE: bypass PCIe DLL.
[    0.000000]  PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[    0.000000]  disable all power about PCIe
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock6 rootfstype=squashfs,jffs2 noinitrd rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0000a4a1
[    0.000000] Readback ErrCtl register=0000a4a1
[    0.000000] Memory: 60008k/65536k available (3485k kernel code, 5528k reserved, 987k data, 196k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] console [ttyS1] enabled
[    0.108000] Calibrating delay loop...
[11:04:59.713]收←◆385.02 BogoMIPS (lpj=770048)
[    0.148000] pid_max: default: 32768 minimum: 301
[    0.152000] Mount-cache hash table entries: 512
[    0.156000] NET: Registered protocol family 16
[    0.160000] RALINK_GPIOMODE = 1ab01d
[    0.164000] RALINK_GPIOMODE = 18b01d
[    0.168000] PPLL_CFG1=0xe2c000
[    0.172000] MT7620 PPLL lock
[    0.176000] PPLL_DRV =0x80080504
[    0.180000] start PCIe register access

[11:05:00.289]收←◆[    0.680000] RALINK_RSTCTRL = 2400000
[    0.684000] RALINK_CLKCFG1 = 75afffc0
[    0.688000]
[    0.688000] *************** MT7620 PCIe RC mode *************

[11:05:00.817]收←◆[    1.188000] PCIE0 enabled
[    1.192000] Port 0 N_FTS = 1b105000
[    1.196000] init_rt2880pci done
[    1.220000] bio: create slab <bio-0> at 0
[    1.224000] PCI host bridge to bus 0000:00
[    1.228000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.232000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    1.236000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.240000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.244000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[    1.248000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    1.252000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[    1.256000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    1.260000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[    1.264000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[    1.268000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.272000] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    1.276000] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
[    1.280000] BAR0 at slot 0 = 0
[    1.284000] bus=0x0, slot = 0x0
[    1.288000] res[0]->start = 0
[    1.292000] res[0]->end = 0
[    1.296000] res[1]->start = 20200000
[    1.300000] res[1]->end = 2020ffff
[    1.304000] res[2]->start = 0
[    1.308000] res[2]->end = 0
[    1.312000] res[3]->start = 0
[    1.316000] res[3]->end = 0
[    1.320000] res[4]->start = 0
[    1.324000] res[4]->end = 0
[    1.328000] res[5]->start = 0
[    1.332000] res[5]->end = 0
[    1.336000] bus=0x1, slot = 0x0
[    1.340000] res[0]->start = 20000000
[    1.344000] res[0]->end = 200fffff
[    1.348000] res[1]->start = 0
[    1.352000] res[1]->end = 0
[    1.356000] res[2]->start = 0
[    1.360000] res[2]->end = 0
[    1.364000] res[3]->start = 0
[    1.368000] res[3]->end = 0
[    1.372000] res[4]->start = 0
[    1.376000] res[4]->end = 0
[    1.380000] res[5]->start = 0
[    1.384000] res[5]->end = 0
[    1.388000] cfg80211: Calling CRDA to update world regulatory domain
[    1.392000] Switching to clocksource MIPS
[    1.396000] NET: Registered protocol family 2
[    1.408000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    1.420000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    1.432000] TCP: Hash tables configured (established 512 bind 512)
[    1.444000] TCP: reno registered
[    1.452000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.464000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.476000] NET: Registered protocol family 1
[    1.488000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.500000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.520000] msgmni has been set to 117
[    1.528000] io scheduler noop registered (default)
[    1.544000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.560000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[    1.572000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[    1.588000] deice id : ef 40 17 0 0 (40170000)
[    1.596000] W25Q64BV(ef 40170000) (8192 Kbytes)
[    1.604000] mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
[    1.624000] Searching for RedBoot partition table
[    1.636000] 9 RedBoot partitions found on MTD device raspi
[    1.644000] Creating 9 MTD partitions on "raspi":
[    1.656000] 0x000000000000-0x00000001d800 : "factory_boot"           ------------------------------------------------------------------------------------------------------这
[    1.664000] mtd: partition "factory_boot" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only   ------------几
[    1.692000] 0x00000001d800-0x00000001e000 : "factory_info"          -------------------------------------------------------------------------------------------------------个
[    1.704000] 0x00000001e000-0x000000020000 : "art"                      --------------------------------------------------------------------------------------------------------应
[    1.716000] 0x000000020000-0x000000030000 : "config"                 --------------------------------------------------------------------------------------------------------该
[    1.728000] 0x000000030000-0x000000040000 : "normal_boot"        --------------------------------------------------------------------------------------------------------是
[    1.740000] 0x000000040000-0x0000001ccc14 : "kernel"                ---------------------------------------------------------------------------------------------------------做
[    1.752000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only                          备
[    1.776000] 0x0000001ccc14-0x0000006b0000 : "rootfs"                ----------------------------------------------------------------------------------------------------------份
[    1.788000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only                           有
[    1.812000] mtd: device 6 (rootfs) set to be root filesystem                                                                                                                                          用
[    1.824000] 0x0000006b0000-0x000000800000 : "rootfs_data"         ---------------------------------------------------------------------------------------------------------的
[    1.836000] 0x000000040000-0x000000800000 : "firmware"            ---------------------------------------------------------------------------------------------------------吧
[    1.848000] register rt2860
[    1.864000]
[    1.864000]
[    1.864000] === pAd = c0181000, size = 1514000 ===
[    1.864000]
[    1.880000] <-- RTMPAllocTxRxRingMemory, Status=0
[    1.892000] <-- RTMPAllocAdapterBlock, Status=0
[    1.900000] pAd->CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
[    1.912000] device_id =0x7662
[    1.920000] ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
[    1.940000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
[    1.948000] RtmpEepromGetDefault::e2p_dafault=2
[    1.960000] NVM is FLASH mode
[    1.964000] tpsteer_netlink_init
[    1.972000] rdm_major = 253
[    1.976000] netif_napi_add() called with weight 128 on device eth0
[    1.988000] SMACCR1 -- : 0x0000000c
[    1.996000] SMACCR0 -- : 0x432880e6
[    2.004000] Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
[    2.024000] NAPI enable, Tx Ring = 512, Rx Ring = 512
[    2.032000] SMACCR1 -- : 0x0000000c
[    2.040000] SMACCR0 -- : 0x4328809b
[    2.048000] PROC INIT OK!
[    2.052000] u32 classifier
[    2.060000]     Performance counters on
[    2.068000]     input device check on
[    2.072000]     Actions configured
[    2.080000] TCP: cubic registered
[    2.088000] NET: Registered protocol family 17
[    2.096000] 8021q: 802.1Q VLAN Support v1.8
[    2.108000] registered taskstats version 1
[    2.116000] Registered character driver slp_flash_chrdev
[    2.132000] Flash UID signiture check failed.
[    2.144000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    2.160000] Freeing unused kernel memory: 196K (8045f000 - 80490000)

afe***

千兆的版本，交换机应该是RTL8367S的吧，cpu集成64M内存，这个暂时没有breed，拆机了居然不上图

maim***

afeng11 发表于 2019-10-16 16:39
千兆的版本，交换机应该是RTL8367S的吧，cpu集成64M内存，这个暂时没有breed，拆机了居然不上图

哦，，一会儿补图，刚才急着去接孩子放学了。

maim***

afeng11 发表于 2019-10-16 16:39
千兆的版本，交换机应该是RTL8367S的吧，cpu集成64M内存，这个暂时没有breed，拆机了居然不上图

已经上图了。。。。

linksy***

还没有适配MT7620DA的breed。

zjh***

linksys_wifi 发表于 2019-10-16 19:00
还没有适配MT7620DA的breed。

强刷应该可以的。但是没有8367的驱动

maim***

zjh1990 发表于 2019-10-16 19:36
强刷应该可以的。但是没有8367的驱动

怎么强刷？编程器算不算。。我用编程器刷十几个breed都不成。。

LGA***

breed 没有适配 8367S，因此你进不去
你可以参考我的 Archer C5v4 的帖子

maim***

LGA1150 发表于 2019-10-16 22:21
breed 没有适配 8367S，因此你进不去
你可以参考我的 Archer C5v4 的帖子

哦，我去看一下。。。。

maim***

LGA1150 发表于 2019-10-16 22:21
breed 没有适配 8367S，因此你进不去
你可以参考我的 Archer C5v4 的帖子

我手里的这台是电信定制版的，，刷了你Archer的固件无法启动。看来一辈子就一个固件了。。。

tzx***

你把原机备份发我一份我看看给你改改看能不能用！383353895@qq.com

小***

我也是TP5620v2.1版，硬改16m，刷breed启动不了，刷原固件正常

沐***

电信版就这么没救么。感觉5g信号最差

niun***

小二蛋 发表于 2020-1-16 14:31
我也是TP5620v2.1版，硬改16m，刷breed启动不了，刷原固件正常

原版的固件能发个吗，自己的没备份。

shenj***

链接：https://pan.baidu.com/s/1er-0KUJgAXHkHCwWuQo8TA
提取码：fmrg
复制这段内容后打开百度网盘手机App，操作更方便哦

我备份的原厂固件，目前有能刷的UBOOT和第三方固件了吗？早知道这样还不如用不带交换芯片的百兆版