求救求救 新手ttl刷hg255d uboot卡住了

芒果布丁

在输入 tftpboot 0x80100000 u-boot-rom-hg255d.bin后

TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: *
ArpTimeoutCheck

ArpTimeoutCheck
T T T T T T T T T T
Retry count exceeded; starting again

ArpTimeoutCheck

ArpTimeoutCheck

Retry count exceeded; starting again
就一直卡在这里了，怎么解决啊？？

chenqwen

U-Boot 1.1.3 (Aug 20 2010 - 19:54:34)
Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fb0000
config usb..
The Flash ID =0000227E
flash_protect ON: from 0xBF000000 to 0xBF01D47F
protect on 0
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.3
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 128 Mbits
DRAM bus: 32 bit
Total memory: 32 MBytes
Flash component: NOR Flash
Date:Aug 20 2010  Time:19:54:34
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
SDRAM bus set to 32 bit
SDRAM size =32 Mbytes
@Start First PHY modio study cmd.
eth_register
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:00:AA:BB:CCD:10
00:AA:BB:CCD:10:
eth_current->name = Eth0 (10/100-M)

netboot_common, argc= 2
*************buf = 0x81fcd620
**********NexTxPacket = 81fe46c0
NetTxPacket = 0x81FE46C0
NetRxPackets[0] = 0x81FE4CC0
NetRxPackets[1] = 0x81FE52C0
NetRxPackets[2] = 0x81FE58C0
NetRxPackets[3] = 0x81FE5EC0
NetRxPackets[4] = 0x81FE64C0
NetRxPackets[5] = 0x81FE6AC0
NetRxPackets[6] = 0x81FE70C0
NetRxPackets[7] = 0x81FE76C0
NetRxPackets[8] = 0x81FE7CC0
NetRxPackets[9] = 0x81FE82C0
NetRxPackets[10] = 0x81FE88C0
NetRxPackets[11] = 0x81FE8EC0
NetRxPackets[12] = 0x81FE94C0
NetRxPackets[13] = 0x81FE9AC0
NetRxPackets[14] = 0x81FEA0C0
NetRxPackets[15] = 0x81FEA6C0
NetRxPackets[16] = 0x81FEACC0
NetRxPackets[17] = 0x81FEB2C0
NetRxPackets[18] = 0x81FEB8C0
NetRxPackets[19] = 0x81FEBEC0
KSEG1ADDR(NetTxPacket) = 0xA1FE46C0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.
You choosed 4

eth_register
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:00:AA:BB:CCD:10
00:AA:BB:CCD:10:
eth_current->name = Eth0 (10/100-M)

4: System Enter Boot Command Line Interface.
U-Boot 1.1.3 (Aug 20 2010 - 19:54:34)
main_loop !!
RT3052 # setenv serverip 192.168.1.100
RT3052 # tftpboot 0x80100000 u-boot-rom-hg255d_hg256.bin
netboot_common, argc= 3
*************buf = 0x81fcd620
**********NexTxPacket = 81fe46c0
NetTxPacket = 0x81FE46C0
NetRxPackets[0] = 0x81FE4CC0
NetRxPackets[1] = 0x81FE52C0
NetRxPackets[2] = 0x81FE58C0
NetRxPackets[3] = 0x81FE5EC0
NetRxPackets[4] = 0x81FE64C0
NetRxPackets[5] = 0x81FE6AC0
NetRxPackets[6] = 0x81FE70C0
NetRxPackets[7] = 0x81FE76C0
NetRxPackets[8] = 0x81FE7CC0
NetRxPackets[9] = 0x81FE82C0
NetRxPackets[10] = 0x81FE88C0
NetRxPackets[11] = 0x81FE8EC0
NetRxPackets[12] = 0x81FE94C0
NetRxPackets[13] = 0x81FE9AC0
NetRxPackets[14] = 0x81FEA0C0
NetRxPackets[15] = 0x81FEA6C0
NetRxPackets[16] = 0x81FEACC0
NetRxPackets[17] = 0x81FEB2C0
NetRxPackets[18] = 0x81FEB8C0
NetRxPackets[19] = 0x81FEBEC0
KSEG1ADDR(NetTxPacket) = 0xA1FE46C0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'u-boot-rom-hg255d_hg256.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: *
ArpTimeoutCheck
ArpTimeoutCheck

chenqwen

貌似跟你一样的。。。

mxsheng

我也一样

寄生

我的也一样