自编译bin固件，能识别网卡，但貌似还不能radio1

liveup

很艰难，能编译出能识别网卡的bin，运行lsusb正常:

root@OpenWrt:~# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170]
root@OpenWrt:~#

但运行dmesg，貌似没看到正式加载。按照网上的方法，应该这一步就直接能看到加载的，现在没法启动radio1。求高手指教！

root@OpenWrt:~# dmesg
[    0.000000] Linux version 3.3.8 (kingf@kingf_pc) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #3 Wed Dec 25 21:50:19 HKT 2013
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9130 rev 2
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:100.000MHz, Ref:5.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8038f600, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR941ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 60876k/65536k available (2748k kernel code, 4660k reserved, 514k data, 192k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR941ND
[    0.370000] bio: create slab <bio-0> at 0
[    0.370000] SCSI subsystem initialized
[    0.380000] usbcore: registered new interface driver usbfs
[    0.380000] usbcore: registered new interface driver hub
[    0.390000] usbcore: registered new device driver usb
[    0.390000] Switching to clocksource MIPS
[    0.400000] NET: Registered protocol family 2
[    0.400000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.410000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.420000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.420000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.430000] TCP reno registered
[    0.430000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.440000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.450000] NET: Registered protocol family 1
[    0.450000] PCI: CLS 0 bytes, default 32
[    0.470000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.480000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.490000] msgmni has been set to 118
[    0.490000] io scheduler noop registered
[    0.500000] io scheduler deadline registered (default)
[    0.500000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.530000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.540000] console [ttyS0] enabled, bootconsole disabled
[    0.550000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    0.560000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    0.560000] 5 tp-link partitions found on MTD device spi0.0
[    0.570000] Creating 5 MTD partitions on "spi0.0":
[    0.570000] 0x000000000000-0x000000020000 : "u-boot"
[    0.580000] 0x000000020000-0x000000140c00 : "kernel"
[    0.580000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.600000] 0x000000140c00-0x000000ff0000 : "rootfs"
[    0.600000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.620000] mtd: partition "rootfs" set to be root filesystem
[    0.620000] mtd: partition "rootfs_data" created automatically, ofs=380000, len=C70000
[    0.630000] 0x000000380000-0x000000ff0000 : "rootfs_data"
[    0.640000] 0x000000ff0000-0x000001000000 : "art"
[    0.640000] 0x000000020000-0x000000ff0000 : "firmware"
[    0.670000] ag71xx_mdio: probed
[    0.670000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    0.980000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.980000] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
[    0.980000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[    0.990000] drivers/usb/core/inode.c: creating file 'devices'
[    0.990000] drivers/usb/core/inode.c: creating file '001'
[    0.990000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    1.000000] ehci-platform ehci-platform: reset hcs_params 0x10011 dbg=0 ind cc=0 pcc=0 ordered ports=1
[    1.000000] ehci-platform ehci-platform: reset hcc_params 0006 thresh 0 uframes 256/512/1024 park
[    1.000000] ehci-platform ehci-platform: park 0
[    1.000000] ehci-platform ehci-platform: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    1.000000] ehci-platform ehci-platform: ...powerdown ports...
[    1.030000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    1.030000] ehci-platform ehci-platform: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[    1.050000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    1.050000] usb usb1: default language 0x0409
[    1.050000] usb usb1: udev 1, busnum 1, minor = 0
[    1.050000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.060000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.070000] usb usb1: Product: Generic Platform EHCI Controller
[    1.070000] usb usb1: Manufacturer: Linux 3.3.8 ehci_hcd
[    1.080000] usb usb1: SerialNumber: ehci-platform
[    1.080000] usb usb1: usb_probe_device
[    1.080000] usb usb1: configuration #1 chosen from 1 choice
[    1.080000] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    1.080000] hub 1-0:1.0: usb_probe_interface
[    1.080000] hub 1-0:1.0: usb_probe_interface - got id
[    1.080000] hub 1-0:1.0: USB hub found
[    1.090000] hub 1-0:1.0: 1 port detected
[    1.090000] hub 1-0:1.0: standalone hub
[    1.090000] hub 1-0:1.0: individual port power switching
[    1.090000] hub 1-0:1.0: individual port over-current protection
[    1.090000] hub 1-0:1.0: Single TT
[    1.090000] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    1.090000] hub 1-0:1.0: power on to power good time: 20ms
[    1.090000] hub 1-0:1.0: local power source is good
[    1.090000] hub 1-0:1.0: enabling power on all ports
[    1.090000] drivers/usb/core/inode.c: creating file '001'
[    1.090000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.100000] ohci_hcd: block sizes: ed 64 td 64
[    1.100000] usbcore: registered new interface driver cdc_acm
[    1.100000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.110000] usbcore: registered new interface driver usblp
[    1.120000] usbcore: registered new interface driver cdc_wdm
[    1.120000] usbcore: registered new interface driver usbtmc
[    1.130000] Initializing USB Mass Storage driver...
[    1.130000] usbcore: registered new interface driver usb-storage
[    1.140000] USB Mass Storage support registered.
[    1.150000] usbcore: registered new interface driver usbserial
[    1.150000] USB Serial support registered for generic
[    1.160000] usbcore: registered new interface driver usbserial_generic
[    1.160000] usbserial: USB Serial Driver core
[    1.170000] USB Serial support registered for pl2303
[    1.170000] usbcore: registered new interface driver pl2303
[    1.180000] pl2303: Prolific PL2303 USB to serial adaptor driver
[    1.190000] TCP cubic registered
[    1.190000] NET: Registered protocol family 17
[    1.190000] Distributed Switch Architecture driver version 0.1
[    1.200000] eth0[0]: detected a Marvell 88E6060 switch
[    1.210000] ehci-platform ehci-platform: GetStatus port:1 status 001803 0  ACK POWER sig=j CSC CONNECT
[    1.210000] hub 1-0:1.0: port 1: status 0101 change 0001
[    1.230000] dsa slave smi: probed
[    1.240000] 8021q: 802.1Q VLAN Support v1.8
[    1.250000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.260000] Freeing unused kernel memory: 192k freed
[    1.310000] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[    1.310000] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[    1.430000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    1.430000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 1
[    1.440000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 2
[    1.440000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 3
[    1.440000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 4
[    1.440000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 5
[    1.440000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 6
[    1.440000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 7
[    1.440000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 8
[    1.450000] ehci-platform ehci-platform: detected XactErr len 0/64 retry 9
[    1.510000] ehci-platform ehci-platform: port 1 high speed
[    1.510000] ehci-platform ehci-platform: GetStatus port:1 status 8001205 4  ACK POWER sig=se0 LPM PE CONNECT
[    1.570000] ehci-platform ehci-platform: detected XactErr len 0/0 retry 1
[    1.570000] ehci-platform ehci-platform: detected XactErr len 0/0 retry 2
[    1.570000] ehci-platform ehci-platform: detected XactErr len 0/0 retry 3
[    1.570000] ehci-platform ehci-platform: detected XactErr len 0/0 retry 4
[    1.570000] ehci-platform ehci-platform: detected XactErr len 0/0 retry 5
[    1.570000] ehci-platform ehci-platform: detected XactErr len 0/0 retry 6
[    1.570000] ehci-platform ehci-platform: detected XactErr len 0/0 retry 7
[    1.610000] ehci-platform ehci-platform: detected XactErr len 0/18 retry 1
[    1.610000] ehci-platform ehci-platform: detected XactErr len 0/18 retry 2
[    1.620000] ehci-platform ehci-platform: detected XactErr len 0/9 retry 1
[    1.620000] ehci-platform ehci-platform: detected XactErr len 0/9 retry 2
[    1.640000] ehci-platform ehci-platform: detected XactErr len 0/46 retry 1
[    1.640000] ehci-platform ehci-platform: detected XactErr len 0/46 retry 2
[    1.640000] ehci-platform ehci-platform: detected XactErr len 0/46 retry 3
[    1.640000] ehci-platform ehci-platform: detected XactErr len 0/46 retry 4
[    1.640000] ehci-platform ehci-platform: detected XactErr len 0/46 retry 5
[    1.640000] ehci-platform ehci-platform: detected XactErr len 0/46 retry 6
[    1.640000] ehci-platform ehci-platform: detected XactErr len 0/46 retry 7
[    1.640000] ehci-platform ehci-platform: detected XactErr len 0/46 retry 8
[    1.650000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 1
[    1.660000] usb 1-1: default language 0x0409
[    1.670000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 1
[    1.670000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 2
[    1.670000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 3
[    1.670000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 4
[    1.680000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 1
[    1.680000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 2
[    1.690000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 1
[    1.690000] ehci-platform ehci-platform: detected XactErr len 0/255 retry 2
[    1.690000] usb 1-1: udev 2, busnum 1, minor = 1
[    1.690000] usb 1-1: New USB device found, idVendor=0cf3, idProduct=1002
[    1.700000] usb 1-1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
[    1.700000] usb 1-1: Product: USB2.0 WLAN
[    1.710000] usb 1-1: Manufacturer: ATHER
[    1.710000] usb 1-1: SerialNumber: 12345
[    1.850000] usb 1-1: usb_probe_device
[    1.850000] usb 1-1: configuration #1 chosen from 1 choice
[    1.860000] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[    1.870000] usbserial_generic 1-1:1.0: usb_probe_interface
[    1.870000] usbserial_generic 1-1:1.0: usb_probe_interface - got id
[    1.870000] drivers/usb/core/inode.c: creating file '002'
[    1.870000] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[    3.730000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[    3.730000] eth0: link up (100Mbps/Full duplex)
[    3.760000] Registered led device: tp-link:green:system
[    3.760000] Registered led device: tp-link:red:qss
[    3.760000] Registered led device: tp-link:green:qss
[    3.760000] Registered led device: tp-link:green:wlan
[    7.120000] JFFS2 notice: (560) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (0 unchecked, 18 orphan) and 29 of xref (0 dead, 18 orphan) found.
[   28.140000] eth0: link down
[   30.100000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[   30.110000] Backport generated by backports.git backports-20130617-4-ge3220f5
[   30.250000] cfg80211: Calling CRDA to update world regulatory domain
[   30.260000] cfg80211: World regulatory domain updated:
[   30.260000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   30.270000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   30.280000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   30.290000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   30.300000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   30.300000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.160000] usbcore: registered new interface driver rt73usb
[   31.190000] ath: EEPROM regdomain: 0x0
[   31.190000] ath: EEPROM indicates default country code should be used
[   31.190000] ath: doing EEPROM country->regdmn map search
[   31.190000] ath: country maps to regdmn code: 0x3a
[   31.190000] ath: Country alpha2 being used: US
[   31.190000] ath: Regpair used: 0x3a
[   31.200000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   31.200000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
[   31.210000] cfg80211: Calling CRDA for country: US
[   31.220000] cfg80211: Regulatory domain changed to country: US
[   31.220000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   31.230000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   31.240000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   31.250000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.250000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.260000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.270000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   31.290000] usbcore: registered new interface driver rt2800usb
[   31.500000] PPP generic driver version 2.4.2
[   31.550000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   31.660000] NET: Registered protocol family 24
[   31.690000] nf_conntrack version 0.5.0 (954 buckets, 3816 max)
[   36.250000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[   36.260000] eth0: link up (100Mbps/Full duplex)
[   36.260000] device lan1 entered promiscuous mode
[   36.270000] device eth0 entered promiscuous mode
[   36.290000] device lan2 entered promiscuous mode
[   36.320000] device lan3 entered promiscuous mode
[   36.320000] device lan4 entered promiscuous mode
[   37.040000] lan1: link up, 100 Mb/s, full duplex, flow control disabled
[   37.040000] br-lan: port 1(lan1) entered forwarding state
[   37.050000] br-lan: port 1(lan1) entered forwarding state
[   39.050000] br-lan: port 1(lan1) entered forwarding state
[   42.990000] wlan0: authenticate with ec:6c:9f:17:f2:a2
[   43.000000] wlan0: send auth to ec:6c:9f:17:f2:a2 (try 1/3)
[   43.010000] wlan0: authenticated
[   43.030000] wlan0: associate with ec:6c:9f:17:f2:a2 (try 1/3)
[   43.040000] wlan0: RX AssocResp from ec:6c:9f:17:f2:a2 (capab=0x431 status=0 aid=3)
[   43.040000] wlan0: associated

liveup

自己顶一次！

风的幻想

我跟你一样，请问解决了吗

liveup

风的幻想 发表于 2014-1-18 12:26
我跟你一样，请问解决了吗

按照网上的教程，能识别3070网卡，就是没法启动。已经排除了usb供电问题。搞不懂。

风的幻想

liveup 发表于 2014-1-18 16:42
按照网上的教程，能识别3070网卡，就是没法启动。已经排除了usb供电问题。搞不懂。

我好像找到方法了。等我的好消息。

liveup

风的幻想 发表于 2014-1-18 19:50
我好像找到方法了。等我的好消息。

祝你顺利，等你的消息！

风的幻想

liveup 发表于 2014-1-18 21:22
祝你顺利，等你的消息！

网编译了一个固件，刷上去挂AR9271，效果很不错。朋友我成功了
详见我这个贴https://www.right.com.cn/forum/fo ... =1&extra=#pid832842，编译的时候把提到的组件加进去就可以了。
看网上的教程说要修改路由的一些文件，结果不用这样做。