[求助] mt7620a问题

dpps5387690

我使用openwrt14.07自行编译后刷入
但是只有无限的可以使用有线的无法连接
是我设定上有问题还是没有驱动

以下是内核log

[    0.000000] Linux version 3.10.49 (user@user-virtual-machine) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48549) ) #1 Sun Sep 18 23:55:06 CST 2016
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: Ralink MT7620A ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Lenovo Y1S
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802d0990, node_mem_map 810063c0
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0007f08b
[    0.000000] Readback ErrCtl register=0007f08b
[    0.000000] Memory: 61508k/65536k available (2381k kernel code, 4028k reserved, 591k data, 224k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 580MHz
[    0.050000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] pinctrl core: initialized pinctrl subsystem
[    0.080000] NET: Registered protocol family 16
[    0.090000] rt2880-pinmux pinctrl.1: try to register 73 pins ...
[    0.090000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 52 (io52) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 53 (io53) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 54 (io54) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 55 (io55) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 56 (io56) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 57 (io57) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 58 (io58) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 59 (io59) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 60 (io60) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 61 (io61) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 62 (io62) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 63 (io63) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 64 (io64) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 65 (io65) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 66 (io66) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 67 (io67) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 68 (io68) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 69 (io69) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 70 (io70) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 71 (io71) on rt2880-pinmux
[    0.090000] pinctrl core: registered pin 72 (io72) on rt2880-pinmux
[    0.090000] pinctrl core: add 4 pinmux maps
[    0.090000] rt2880-pinmux pinctrl.1: found group selector 1 for uartf
[    0.090000] rt2880-pinmux pinctrl.1: found group selector 11 for wled
[    0.090000] rt2880-pinmux pinctrl.1: found group selector 9 for nd_sd
[    0.090000] rt2880-pinmux pinctrl.1: found group selector 13 for pa
[    0.090000] rt2880-pinmux pinctrl.1: request pin 7 (io7) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 8 (io8) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 9 (io9) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 10 (io10) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 11 (io11) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 12 (io12) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 13 (io13) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 14 (io14) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 72 (io72) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 45 (io45) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 46 (io46) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 47 (io47) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 48 (io48) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 49 (io49) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 50 (io50) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 51 (io51) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 52 (io52) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 53 (io53) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 54 (io54) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 55 (io55) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 56 (io56) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 57 (io57) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 58 (io58) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 59 (io59) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 18 (io18) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 19 (io19) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 20 (io20) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: request pin 21 (io21) for pinctrl.1
[    0.090000] rt2880-pinmux pinctrl.1: failed to lookup the sleep state
[    0.520000] PCIE0 no card, disable it(RST&CLK)
[    0.530000] bio: create slab <bio-0> at 0
[    0.540000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.550000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.560000] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.570000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.580000] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.590000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.600000] PCI host bridge to bus 0000:00
[    0.610000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    0.620000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    0.630000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.640000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.640000] Switching to clocksource MIPS
[    0.650000] NET: Registered protocol family 2
[    0.650000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.660000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.670000] TCP: Hash tables configured (established 512 bind 512)
[    0.690000] TCP: reno registered
[    0.690000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.700000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.720000] NET: Registered protocol family 1
[    0.730000] PCI: CLS 0 bytes, default 32
[    0.730000] rt-timer 10000100.timer: maximum frequncy is 2441Hz
[    0.740000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
[    0.750000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.770000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.790000] msgmni has been set to 120
[    0.790000] io scheduler noop registered
[    0.800000] io scheduler deadline registered (default)
[    0.810000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.830000] serial8250 serial8250: no of_node; not parsing pinctrl DT
[    0.830000] pinctrl core: add 1 pinmux maps
[    0.830000] rt2880-pinmux pinctrl.1: found group selector 3 for uartlite
[    0.830000] rt2880-pinmux pinctrl.1: request pin 15 (io15) for 10000c00.uartlite
[    0.830000] rt2880-pinmux pinctrl.1: request pin 16 (io16) for 10000c00.uartlite
[    0.830000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    0.840000] console [ttyS0] enabled, bootconsole disabled
[    0.860000] pinctrl core: add 1 pinmux maps
[    0.860000] rt2880-pinmux pinctrl.1: found group selector 2 for spi
[    0.860000] rt2880-pinmux pinctrl.1: request pin 3 (io3) for 10000b00.spi
[    0.860000] rt2880-pinmux pinctrl.1: request pin 4 (io4) for 10000b00.spi
[    0.860000] rt2880-pinmux pinctrl.1: request pin 5 (io5) for 10000b00.spi
[    0.860000] rt2880-pinmux pinctrl.1: request pin 6 (io6) for 10000b00.spi
[    0.860000] m25p80 spi32766.0: found mx25l12805d, expected w25q128
[    0.870000] m25p80 spi32766.0: mx25l12805d (16384 Kbytes)
[    0.870000] 4 ofpart partitions found on MTD device spi32766.0
[    0.880000] Creating 4 MTD partitions on "spi32766.0":
[    0.880000] 0x000000000000-0x000000030000 : "u-boot"
[    0.890000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.900000] 0x000000040000-0x000000050000 : "factory"
[    0.900000] 0x000000050000-0x000001000000 : "firmware"
[    0.910000] 0x000000156e78-0x000001000000 : "rootfs"
[    0.920000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.930000] mtd: device 4 (rootfs) set to be root filesystem
[    0.940000] mtd: partition "rootfs_data" created automatically, ofs=0x680000, len=0x980000
[    0.940000] 0x000000680000-0x000001000000 : "rootfs_data"
[    0.950000] pinctrl core: add 1 pinmux maps
[    0.950000] pinctrl core: add 1 pinmux maps
[    0.950000] pinctrl core: add 1 pinmux maps
[    0.950000] rt2880-pinmux pinctrl.1: found group selector 6 for rgmii1
[    0.950000] rt2880-pinmux pinctrl.1: found group selector 10 for rgmii2
[    0.950000] rt2880-pinmux pinctrl.1: found group selector 5 for mdio
[    0.950000] rt2880-pinmux pinctrl.1: request pin 24 (io24) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 25 (io25) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 26 (io26) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 27 (io27) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 28 (io28) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 29 (io29) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 30 (io30) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 31 (io31) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 32 (io32) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 33 (io33) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 34 (io34) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 35 (io35) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 60 (io60) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 61 (io61) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 62 (io62) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 63 (io63) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 64 (io64) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 65 (io65) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 66 (io66) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 67 (io67) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 68 (io68) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 69 (io69) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 70 (io70) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 71 (io71) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 22 (io22) for 10100000.ethernet
[    0.950000] rt2880-pinmux pinctrl.1: request pin 23 (io23) for 10100000.ethernet
[    0.960000] libphy: mdio: probed
[    0.960000] ralink_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=03a2940d, driver=Generic PHY]
[    0.970000] ralink_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=0000ffff, driver=Generic PHY]
[    0.980000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.990000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[    1.000000] rt3xxx-usbphy usbphy.3: loaded
[    1.000000] rt2880_wdt 10000120.watchdog: Initialized
[    1.010000] TCP: cubic registered
[    1.010000] NET: Registered protocol family 17
[    1.020000] 8021q: 802.1Q VLAN Support v1.8
[    1.040000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.040000] Freeing unused kernel memory: 224K (802e8000 - 80320000)
[    6.400000] usbcore: registered new interface driver usbfs
[    6.410000] usbcore: registered new interface driver hub
[    6.410000] usbcore: registered new device driver usb
[    6.420000] Button Hotplug driver version 0.4.1
[    6.460000] rt2880-pinmux pinctrl.1: request pin 11 (io11) for pio:11
[    6.470000] SCSI subsystem initialized
[    6.480000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.480000] ehci-platform: EHCI generic platform driver
[    6.690000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[    6.700000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[    6.700000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    6.710000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    6.720000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    6.740000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    6.740000] usb usb1: no of_node; not parsing pinctrl DT
[    6.740000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
[    6.740000] hub 1-0:1.0: USB hub found
[    6.750000] hub 1-0:1.0: 1 port detected
[    6.750000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.760000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller
[    6.770000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    6.780000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    6.840000] usb usb2: no of_node; not parsing pinctrl DT
[    6.840000] hub 2-0:1.0: no of_node; not parsing pinctrl DT
[    6.840000] hub 2-0:1.0: USB hub found
[    6.840000] hub 2-0:1.0: 1 port detected
[    6.850000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    6.860000] rt2880-pinmux pinctrl.1: request pin 14 (io14) for pio:14
[    6.860000] rt2880-pinmux pinctrl.1: request pin 9 (io9) for pio:9
[    6.860000] rt2880-pinmux pinctrl.1: request pin 72 (io72) for pio:72
[    6.860000] rt2880-pinmux pinctrl.1: request pin 50 (io50) for pio:50
[    6.860000] rt2880-pinmux pinctrl.1: request pin 53 (io53) for pio:53
[    6.860000] rt2880-pinmux pinctrl.1: request pin 52 (io52) for pio:52
[    6.860000] rt2880-pinmux pinctrl.1: request pin 51 (io51) for pio:51
[    6.870000] sdhci: Secure Digital Host Controller Interface driver
[    6.880000] sdhci: Copyright(c) Pierre Ossman
[    6.880000] MTK MSDC device init.
[    6.890000] mtk-sd: MediaTek MT6575 MSDC Driver
[    6.890000] sdhci-pltfm: SDHCI platform and OF driver helper
[    6.900000] usbcore: registered new interface driver usb-storage
[    6.910000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[    6.920000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[    7.780000] 8021q: adding VLAN 0 to HW filter on device eth0
[    8.960000] ralink_soc_eth 10100000.ethernet eth0: port 4 link up (10Mbps/Half duplex)
[    8.970000] ralink_soc_eth 10100000.ethernet eth0: port 5 link up (10Mbps/Half duplex)
[   11.310000] jffs2: notice: (344) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 13 of xref (0 dead, 2 orphan) found.
[   12.020000] ralink_soc_eth 10100000.ethernet eth0: port 4 link down
[   12.020000] ralink_soc_eth 10100000.ethernet eth0: port 5 link down
[   13.520000] NET: Registered protocol family 10
[   13.540000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   13.590000] tun: Universal TUN/TAP device driver, 1.6
[   13.590000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   13.610000] l2tp_core: L2TP core driver, V2.0
[   13.630000] l2tp_netlink: L2TP netlink interface
[   13.630000] gre: GRE over IPv4 demultiplexor driver
[   13.640000] ip_gre: GRE over IPv4 tunneling driver
[   13.670000] ip6_gre: GRE over IPv6 tunneling driver
[   13.690000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[   13.710000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.730000] Netfilter messages via NETLINK v0.30.
[   13.750000] ip_set: protocol 6
[   13.820000] hidraw: raw HID events driver (C) Jiri Kosina
[   13.860000] fuse init (API version 7.22)
[   13.880000] usbcore: registered new interface driver cdc_acm
[   13.880000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   13.910000] usbcore: registered new interface driver cdc_wdm
[   13.920000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   13.930000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   13.940000] Error: Driver 'gpio-keys' is already registered, aborting...
[   13.950000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[   13.960000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.010000] usbcore: registered new interface driver usbserial
[   14.020000] usbcore: registered new interface driver usbserial_generic
[   14.020000] usbserial: USB Serial support registered for generic
[   14.070000] xt_time: kernel timezone is -0000
[   14.080000] usbcore: registered new interface driver asix
[   14.090000] usbcore: registered new interface driver cdc_ether
[   14.100000] usbcore: registered new interface driver cdc_ncm
[   14.110000] usbcore: registered new interface driver cdc_subset
[   14.150000] cfg80211: Calling CRDA to update world regulatory domain
[   14.150000] cfg80211: World regulatory domain updated:
[   14.160000] cfg80211:  DFS Master region: unset
[   14.160000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   14.170000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.180000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.190000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   14.200000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   14.200000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   14.210000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   14.220000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.230000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   14.240000] usbcore: registered new interface driver ftdi_sio
[   14.260000] usbserial: USB Serial support registered for FTDI USB Serial Device
[   14.270000] Error: Driver 'gpio-keys' is already registered, aborting...
[   14.280000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[   14.340000] PPP generic driver version 2.4.2
[   14.350000] PPP MPPE Compression module registered
[   14.360000] NET: Registered protocol family 24
[   14.360000] PPTP driver version 0.8.5
[   14.370000] usbcore: registered new interface driver qmi_wwan
[   14.380000] usbcore: registered new interface driver rndis_host
[   14.410000] usbcore: registered new interface driver sierra_net
[   14.420000] Error: Driver 'gpio-keys' is already registered, aborting...
[   14.430000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[   14.450000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   14.450000] usbcore: registered new interface driver option
[   14.460000] usbserial: USB Serial support registered for GSM modem (1-port)
[   14.470000] usbcore: registered new interface driver qcserial
[   14.480000] usbserial: USB Serial support registered for Qualcomm USB modem
[   14.510000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
[   14.520000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   14.530000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   14.550000] Error: Driver 'gpio-keys' is already registered, aborting...
[   14.570000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[   22.950000] 8021q: adding VLAN 0 to HW filter on device eth0
[   22.950000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.980000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[   22.980000] device eth0.1 entered promiscuous mode
[   22.990000] device eth0 entered promiscuous mode
[   23.000000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   23.160000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   23.380000] ralink_soc_eth 10100000.ethernet eth0: port 4 link up (10Mbps/Half duplex)
[   23.390000] ralink_soc_eth 10100000.ethernet eth0: port 5 link up (10Mbps/Half duplex)
[   25.380000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.380000] br-lan: port 1(eth0.1) entered forwarding state
[   25.390000] br-lan: port 1(eth0.1) entered forwarding state
[   25.390000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   25.400000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   25.430000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   25.720000] nodogsplash uses obsolete (PF_INET,SOCK_PACKET)
[   25.740000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   25.750000] device wlan0 entered promiscuous mode
[   25.750000] br-lan: port 2(wlan0) entered forwarding state
[   25.760000] br-lan: port 2(wlan0) entered forwarding state
[   25.850000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   27.390000] br-lan: port 1(eth0.1) entered forwarding state
[   27.760000] br-lan: port 2(wlan0) entered forwarding state