找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 3583|回复: 16

请 恩山无线 及各位网友帮忙看看 wbr2-g54

[复制链接]
发表于 2008-12-27 23:39 | 显示全部楼层 |阅读模式
请 恩山无线 及各位网友帮忙看看 wbr2-g54
我的wbr2-g54 现在无法ping通 但是通过ttl线看到cfe正常启动。请各位帮忙解决,万分感谢!!


CFE version 1.0.37-1.00.0.02 for BCM947XX (32bit,SP,LE)
Build Date: Tue, 16 Nov 2004 18:56:26 +0900 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena.
Initializing Devices.
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.60.9.0
* memc_config: (00048000) -> [00048540]
CPU type 0x29007: 200MHz
Total memory: 0x1000000 bytes (16MB)

Total memory used by CFE:  0x80400000 - 0x8053CD30 (1297712)
Initialized Data:          0x80436E50 - 0x80439580 (10032)
BSS Area:                  0x80439580 - 0x8043AD30 (6064)
Local Heap:                0x8043AD30 - 0x8053AD30 (1048576)
Stack Area:                0x8053AD30 - 0x8053CD30 (8192)
Text (code) segment:       0x80400000 - 0x80436E50 (224848)
Boot area (physical):      0x0053D000 - 0x0057D000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-0D-0B-6D-2B-62, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
Invalid boot block on disk
Reading :: et0: link up (interface up)
Failed.: Timeout occured
Reading :: Failed.: Timeout occured
Reading :: Failed.: Timeout occured
Reading :: Failed.: Timeout occured
Reading :: Failed.: Timeout occured
Reading :: Failed.: Timeout occured
Reading :: Failed.: Timeout occured
Reading :: Failed.: Timeout occured
Reading :: Failed.: Timeout occured
Reading ::

[ 本帖最后由 eason123456 于 2009-3-25 22:42 编辑 ]
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2008-12-27 23:44 | 显示全部楼层
自己顶一顶!!朋友们快来帮帮我!!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2008-12-28 01:43 | 显示全部楼层
你ping哪个ip,wbr2-g54的ip是192.168.11.1
从你上面的信息看,你的路由没固件,tftp个固件问题就解决了。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2008-12-29 18:08 | 显示全部楼层
谢谢你的指点,但是我现在无法ping通 192.168.11.1

我用jtag 写 kernel (wbr2-g54 2.32 firmware)后变成这样

CFE version 1.0.37-1.00.0.02 for BCM947XX (32bit,SP,LE)
Build Date: Tue, 16 Nov 2004 18:56:26 +0900 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena.
Initializing Devices.
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.60.9.0
* memc_config: (00048000) -> [00048540]
CPU type 0x29007: 200MHz
Total memory: 0x1000000 bytes (16MB)

Total memory used by CFE:  0x80400000 - 0x8053CD30 (1297712)
Initialized Data:          0x80436E50 - 0x80439580 (10032)
BSS Area:                  0x80439580 - 0x8043AD30 (6064)
Local Heap:                0x8043AD30 - 0x8053AD30 (1048576)
Stack Area:                0x8053AD30 - 0x8053CD30 (8192)
Text (code) segment:       0x80400000 - 0x80436E50 (224848)
Boot area (physical):      0x0053D000 - 0x0057D000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-0D-0B-6D-2B-62, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
Reading :: et0: link up (interface up)
Failed.: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ...... 1564672 bytes read
Entry at 0x80001000
Closing network.
et0: link down (interface down)
Starting program at 0x80001000
CPU revision is: 00029007
Primary instruction cache 8kb, linesize 16 bytes (2 ways)
Primary data cache 4kb, linesize 16 bytes (2 ways)
Linux version 2.4.20 (root@fc9vm) (gcc version 3.2.3 with Broadcom modifications) #1 Sun Dec 21 19:29:17 CST 2008
Setting the PFC value as 0x15
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
CPU: BCM4712 rev 1 at 200 MHz
Calibrating delay loop... 199.47 BogoMIPS
Memory: 14464k/16384k available (1336k kernel code, 1920k reserved, 108k data, 64k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Disabled
PCI: Fixing up bus 0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 0) is a 16550A
HDLC line discipline: version $Revision: 1.1.1.4 $, maxframe=4096
N_HDLC line discipline registered.
PPP generic driver version 2.4.2
Support for command set 0006 not present
cfi_probe: No supported Vendor Command Set found
pflash: cfi_probe failed
sflash: found no supported devices
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (8092 buckets, 4096 max) - 368 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "mtdblock2" or 1f:02
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on 1f:02
<0>Rebooting in 3 seconds..Please stand by while rebooting the system...
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2008-12-29 18:20 | 显示全部楼层
这是原始没有弄过的时候,启动的cfe
CFE version 1.0.37-1.00.0.02 for BCM947XX (32bit,SP,LE)
Build Date: Tue, 16 Nov 2004 18:56:26 +0900 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena.
Initializing Devices.
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.60.9.0
* memc_config: (00048000) -> [00048540]
CPU type 0x29007: 200MHz
Total memory: 0x1000000 bytes (16MB)

Total memory used by CFE:  0x80400000 - 0x8053CD30 (1297712)
Initialized Data:          0x80436E50 - 0x80439580 (10032)
BSS Area:                  0x80439580 - 0x8043AD30 (6064)
Local Heap:                0x8043AD30 - 0x8053AD30 (1048576)
Stack Area:                0x8053AD30 - 0x8053CD30 (8192)
Text (code) segment:       0x80400000 - 0x80436E50 (224848)
Boot area (physical):      0x0053D000 - 0x0057D000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-0D-0B-6D-2B-62, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
Reading :: et0: link up (interface up)
Failed.: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ..... 1503232 bytes read
Entry at 0x80001000
Closing network.
et0: link down (interface down)
Starting program at 0x80001000
CPU revision is: 00029007
Primary instruction cache 8kb, linesize 16 bytes (2 ways)
Primary data cache 4kb, linesize 16 bytes (2 ways)
Linux version 2.4.20 (root@localhost.localdomain) (gcc version 3.0 20010422 (prerelease) with bcm4710a0 modifications) #37 Fri Sep 24 16:36:34 JST 2004
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
CPU: BCM4712 rev 1 at 200 MHz
Calibrating delay loop... 199.47 BogoMIPS
Memory: 14400k/16384k available (1269k kernel code, 1984k reserved, 108k data, 68k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
BUFFALO WBR-B11 INIT SWICH DRIVER ver 1.00
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 0) is a 16550A
PPP generic driver version 2.4.2
Support for command set 0006 not present
cfi_probe: No supported Vendor Command Set found
pflash: cfi_probe failed
sflash: found no supported devices
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 344 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
*** #define HZ is (100).
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "mtdblock2" or 1f:02
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on 1f:02
<0>Rebooting in 3 seconds..
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2008-12-29 18:21 | 显示全部楼层
这我发现的,应该算是错误吧

Device eth0:  hwaddr 00-0D-0B-6D-2B-62, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
Reading :: et0: link up (interface up)
Failed.: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)

请给位高手帮忙解决
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2008-12-29 22:18 | 显示全部楼层
上面那没什么错误,这类路由器启动基本都这个状态。
你加电后按ctrl+c进入cfe环境,用nvram erase命令清一下nvram试试。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2009-1-1 18:55 | 显示全部楼层
CFE> nvram erase
*** command status = 0


执行以后还是一样
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2009-1-1 19:03 | 显示全部楼层
论坛内有,自己搜索一下
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2009-1-9 21:56 | 显示全部楼层
找不到啊,知道的请说一声!!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2009-1-9 22:04 | 显示全部楼层
我的机器是WBR2-G54S,我也需要。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2009-1-9 23:15 | 显示全部楼层
唉,真懒

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2009-1-10 21:56 | 显示全部楼层
谢谢老大
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2009-1-31 23:20 | 显示全部楼层
刷了之后还是这样啊

reboot


CFE version 1.0.37-1.00.0.02 for BCM947XX (32bit,SP,LE)
Build Date: Tue, 16 Nov 2004 18:56:26 +0900 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena.
Initializing Devices.
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.60.9.0
* memc_config: (00048000) -> [00048540]
CPU type 0x29007: 200MHz
Total memory: 0x1000000 bytes (16MB)

Total memory used by CFE:  0x80400000 - 0x8053CD30 (1297712)
Initialized Data:          0x80436E50 - 0x80439580 (10032)
BSS Area:                  0x80439580 - 0x8043AD30 (6064)
Local Heap:                0x8043AD30 - 0x8053AD30 (1048576)
Stack Area:                0x8053AD30 - 0x8053CD30 (8192)
Text (code) segment:       0x80400000 - 0x80436E50 (224848)
Boot area (physical):      0x0053D000 - 0x0057D000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-0D-0B-55-E4-C2, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
Reading :: et0: link up (interface up)
Failed.: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ...... 1564672 bytes read
Entry at 0x80001000
Closing network.
et0: link down (interface down)
Starting program at 0x80001000
CPU revision is: 00029007
Primary instruction cache 8kb, linesize 16 bytes (2 ways)
Primary data cache 4kb, linesize 16 bytes (2 ways)
Linux version 2.4.20 (root@fc9vm) (gcc version 3.2.3 with Broadcom modifications) #1 Sun Dec 21 19:29:17 CST 2008
Setting the PFC value as 0x15
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
CPU: BCM4712 rev 1 at 200 MHz
Calibrating delay loop... 199.47 BogoMIPS
Memory: 14464k/16384k available (1336k kernel code, 1920k reserved, 108k data, 64k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Disabled
PCI: Fixing up bus 0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 0) is a 16550A
HDLC line discipline: version $Revision: 1.1.1.4 $, maxframe=4096
N_HDLC line discipline registered.
PPP generic driver version 2.4.2
Support for command set 0006 not present
cfi_probe: No supported Vendor Command Set found
pflash: cfi_probe failed
sflash: found no supported devices
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (8092 buckets, 4096 max) - 368 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "mtdblock2" or 1f:02
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on 1f:02
<0>Rebooting in 3 seconds..Please stand by while rebooting the system...


CFE version 1.0.37-1.00.0.02 for BCM947XX (32bit,SP,LE)
Build Date: Tue, 16 Nov 2004 18:56:26 +0900 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena.
Initializing Devices.
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
* cmdset: unknown (0006)
-> use AMD Standard
* Insaner_1 = (0x2a)
* flashutl_cmd: type (0004), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0003), read_id (0090)
-> vendid (00DA), devid (222A), devid2 (0000)
* flashutl_cmd: type (0002), read_id (0090)
-> vendid (0019), devid (1000), devid2 (0000)
* Flash Info. -> manufacturer (FF), device (FF)
* Flash Info. -> manufacturer2 (0000), device2 (0000)
* Insaner_2 = (0x2a)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.60.9.0
* memc_config: (00048000) -> [00048540]
CPU type 0x29007: 200MHz
Total memory: 0x1000000 bytes (16MB)

Total memory used by CFE:  0x80400000 - 0x8053CD30 (1297712)
Initialized Data:          0x80436E50 - 0x80439580 (10032)
BSS Area:                  0x80439580 - 0x8043AD30 (6064)
Local Heap:                0x8043AD30 - 0x8053AD30 (1048576)
Stack Area:                0x8053AD30 - 0x8053CD30 (8192)
Text (code) segment:       0x80400000 - 0x80436E50 (224848)
Boot area (physical):      0x0053D000 - 0x0057D000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-0D-0B-55-E4-C2, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
Automatic startup canceled via Ctrl-C
CFE> et0: link up (interface up)
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2009-3-25 13:25 | 显示全部楼层
自己顶,请各位高手帮帮忙
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 06:38

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表