n1刷原厂变砖ttl进去u盘的文件写不进去-头大-大佬帮忙看看啥原因

poy***

GXL:BL1:9ac50e:bb16dc;FEAT:BDFC31BC:0OC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 308363

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R2048 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R2048 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R2048 check pass!
Load bl33 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00053400
aml log : R2048 check pass!
NOTICE:  BL3-1: v1.0(release):a625749
NOTICE:  BL3-1: Built : 11:25:15, Aug 25 2017
[BL31]: GXL CPU setup!
NOTICE:  BL31: BL33 decompress pass
mpu_config_enablek
[Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
OPS=0x04
d1 80 59 4 cf 8a 8 bc 68 ed 59 c3 [0.896365 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01-00010-gfe36fb9 (Mar 02 2018 - 19:00:28)

DRAM:  2 GiB
Relocation Offset is: 76ed9000
register usb cfg[0][1] = 0000000077f5d330
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
MMC:   aml_priv->desc_buf = 0x0000000073ed9640
aml_priv->desc_buf = 0x0000000073edb960
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
dtb magic 71b104da
aml log : R2048 check pass!
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p230 variant: 2g
        dtb 0 soc: gxl   plat: p230   vari: 1g
        dtb 1 soc: gxl   plat: p230   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073ede1b0,dt_addr=0000000073ee91b0
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p230 variant: 2g
        dtb 0 soc: gxl   plat: p230   vari: 1g
        dtb 1 soc: gxl   plat: p230   vari: 2g
      Find match dtb: 1
parts: 10
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06:      boot   0000000002000000 1
07:    system   0000000050000000 1
08:     cache   0000000020000000 2
09:      data   ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 6, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-917: calc 619e8f20, store 619e8f20
_verify_dtb_checksum()-917: calc 619e8f20, store 619e8f20
dtb_read()-1039: total valid 2
dtb_read()-1106: do nothing
aml log : R2048 check pass!
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p230 variant: 2g
        dtb 0 soc: gxl   plat: p230   vari: 1g
        dtb 1 soc: gxl   plat: p230   vari: 2g
      Find match dtb: 1
vpp: vpp_pq_load pq val error !!!
Net:   Phy 0 not found
dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0

Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[CANVAS]addr=0x7f851000 width=3840, height=2160
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac_wifi] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
InUsbBurn
noSof
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0

poy***

gxl_p230_v1#usb_update bootloader bootloader.img
usb_start_count 0
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... init_part() 278: PART_TYPE_DOS
1 Storage Device(s) found
** Partition 1 not valid on device 0 **

** Unable to use usb 0:1 for device probe **
[FAT_ERR]L747,Error: broken fs_type sign
[FAT_ERR]L954,Error: reading boot sector
Fail to open file (bootloader.img)
ERR(../drivers/usb/gadget/v2_burning/v2_usb_burn/optimus_usb_update.c)L92:Fail when parse file format

poy***

poyang 发表于 2020-8-20 07:42
gxl_p230_v1#usb_update bootloader bootloader.img
usb_start_count 0
(Re)start USB...

这是刷u盘文件报错