请问FW150R如何中断启动？？

wl***

TTL启动信息如下，请问如何中断UBOOT启动？？？

U-Boot 1.1.4 (Dec  3 2009 - 10:03:23)

AP91 (ar7240) U-boot
DRAM:  
sri
#### TAP VALUE 1 = a, 2 = a
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 2.6.34.7-svn15928 (root@dd-wrt) (gcc version 4.3.3 (GCC) ) #2414 Sat Dec 18 09:36:59 CET 2010
[    0.000000] flash_size passed from bootloader = 4
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Booting AR7240(Python)...
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29696k/32768k available (1999k kernel code, 3072k reserved, 336k data, 144k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 232.65 BogoMIPS (lpj=1163264)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] NET: Registered protocol family 16
[    0.240000] PCI init:ar7240_pcibios_init
[    0.240000] registering PCI controller with io_map_base unset
[    0.250000] bio: create slab <bio-0> at 0
[    0.260000] PCI: fixup device 0000:00:00.0
[    0.270000] found calibration data for slot 0 on 0xBF3F1000
[    0.280000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    0.290000] pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff 64bit] (PCI address [0x10000000-0x1000ffff]
[    0.300000] Returning IRQ 48
[    0.300000] fixup irq: got 48
[    0.300000] Switching to clocksource MIPS
[    0.310000] NET: Registered protocol family 2
[    0.310000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.320000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.330000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.330000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.340000] TCP reno registered
[    0.340000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.350000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.350000] NET: Registered protocol family 1
[    0.360000] gpio_proc: module loaded and /proc/gpio/ created
[    0.370000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[    0.370000] init_vdso successfull
[    0.380000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[    0.380000] msgmni has been set to 58
[    0.390000] io scheduler noop registered
[    0.390000] io scheduler deadline registered (default)
[    0.400000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.410000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
[    0.410000] console [ttyS0] enabled, bootconsole disabled
[    0.410000] console [ttyS0] enabled, bootconsole disabled
[    0.420000] guessed flashsize = 4M
[    0.430000] scanning for root partition
[    0.430000] tplink uboot detected
[    0.440000] guessed bootloader size = 20000
[    0.440000]
[    0.440000] found squashfs at 160000
[    0.450000] Creating 8 MTD partitions on "ar7240-nor0":
[    0.460000] 0x000000000000-0x000000020000 : "RedBoot"
[    0.460000] 0x000000020000-0x0000003e0000 : "linux"
[    0.470000] 0x000000160000-0x0000003d0000 : "rootfs"
[    0.470000] mtd: partition "rootfs" set to be root filesystem
[    0.480000] 0x0000003d0000-0x0000003e0000 : "ddwrt"
[    0.490000] 0x0000003e0000-0x0000003f0000 : "nvram"
[    0.490000] 0x0000003f0000-0x000000400000 : "board_config"
[    0.500000] 0x000000000000-0x000000400000 : "fullflash"
[    0.500000] 0x000000000000-0x000000020000 : "fullboot"
[    0.510000] PPP generic driver version 2.4.2
[    0.520000] PPP Deflate Compression module registered
[    0.520000] PPP BSD Compression module registered
[    0.530000] PPP MPPE Compression module registered
[    0.530000] NET: Registered protocol family 24
[    0.540000] PPPoL2TP kernel driver, V1.0
[    0.540000] IMQ driver loaded successfully.
[    0.550000]  Hooking IMQ before NAT on PREROUTING.
[    0.550000]  Hooking IMQ after NAT on POSTROUTING.
[    0.560000] tun: Universal TUN/TAP device driver, 1.6
[    0.560000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.570000] AG7240: Length per segment 1544
[    0.570000] AG7240: Max segments per packet 1
[    0.580000] AG7240: Max tx descriptor count    80
[    0.580000] AG7240: Max rx descriptor count    252
[    0.580000] AG7240: fifo cfg 3 01f00140
[    0.590000] AG7240CHH: Mac address for unit 0
[    0.590000] AG7240CHH: ff:ff:ff:ff:ff:ff
[    0.800000] AG7240CHH: Mac address for unit 1
[    0.800000] AG7240CHH: ff:ff:ff:ff:ff:ff
[    1.010000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[    1.020000] u32 classifier
[    1.020000]     input device check on
[    1.020000]     Actions configured
[    1.030000] Netfilter messages via NETLINK v0.30.
[    1.030000] nf_conntrack version 0.5.0 (464 buckets, 1856 max)
[    1.040000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    1.040000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    1.050000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    1.060000] nf_conntrack_rtsp v0.6.21 loading
[    1.060000] nf_nat_rtsp v0.6.21 loading
[    1.070000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.070000] IPP2P v0.8.2 loading
[    1.080000] TCP westwood registered
[    1.080000] TCP hybla registered
[    1.080000] TCP vegas registered
[    1.090000] NET: Registered protocol family 17
[    1.090000] Bridge firewalling registered
[    1.100000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    1.100000] All bugs added by David S. Miller <davem@redhat.com>
[    1.150000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.150000] Freeing unused kernel memory: 144k freed
start service
starting Architecture code for wr741
Jan  1 00:00:02 udevtrigger[161]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
load ATH Ethernet Driver
configure eth0 to e0:05:c5:65:47:3c
configure eth1 to E0:05:C5:65:47:3D
[    3.590000] ag7240_ring_alloc Allocated 1280 at 0x818b9800
[    3.590000] ag7240_ring_alloc Allocated 4032 at 0x81a09000
[    3.600000] Setting PHY...
[    6.600000] ag7240_ring_alloc Allocated 1280 at 0x81979000
[    6.610000] ag7240_ring_alloc Allocated 4032 at 0x81b45000
[    6.610000] ATHRS26: resetting s26
[    6.720000] ATHRS26: s26 reset done
[    6.720000] Setting PHY...

wl***

load ATH 802.11 a/b/g Driver
load ATH 802.11n Driver
[    7.980000] ath_mimo_hal: module license 'Proprietary' taints kernel.
[    7.980000] Disabling lock debugging due to kernel taint
[    8.010000] ath_mimo_hal: 0.9.17.1 (AR5416, REGOPS_FUNC)
[    8.530000] ath_mimo_pci: 0.9.4.5 (Atheros/multi-bss)
[    8.540000] ath_mimo_pci: CR-LSDK-1.4.0.144
[    8.540000] ath_dfs: Version 2.0.0
[    8.540000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
[    8.550000] wlan: 0.8.4.2 (Atheros/multi-bss)
[    8.560000] wlan: mac acl policy registered
[    8.560000] ath_rate_atheros: Version 2.0.1
[    8.560000] Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
[    8.580000] IRQ 48/wifi%d: IRQF_DISABLED is not guaranteed on shared IRQs
[    8.580000] device id 2B
[    8.600000] 1Mbps 2Mbps 5.5Mbps 11Mbps
[    8.610000] 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[    8.610000] 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[    8.620000]  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[    8.630000] 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[    8.640000]  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[    8.640000] 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[    8.650000]  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[    8.650000] wifi0: mac 192.2 phy 14.0 radio 12.0
[    8.660000] wifi0: Use hw queue 1 for WME_AC_BE traffic
[    8.660000] wifi0: Use hw queue 0 for WME_AC_BK traffic
[    8.670000] wifi0: Use hw queue 2 for WME_AC_VI traffic
[    8.680000] wifi0: Use hw queue 3 for WME_AC_VO traffic
[    8.700000] AG7240: enet unit:1 phy:2 is up...Mii 100Mbps full duplex
[    8.710000] AG7240: done cfg2 0x7215 ifctl 0x0 miictrl  
[    8.710000] wifi0: Use hw queue 8 for CAB traffic
[    8.720000] wifi0: Use hw queue 9 for beacons
[    8.720000] wifi0: Use hw queue 7 for UAPSD
[    8.730000] wifi0: Atheros 9285: mem=0x10000000, irq=48 hw_base=0xb0000000
configure wifi0 to E0:05:C5:65:47:3C
[   10.430000] device br0 entered promiscuous mode
[   10.460000] ag7240_ring_free Freeing at 0x818b9800
[   10.460000] ag7240_ring_free Freeing at 0x81a09000
[   10.480000] ag7240_ring_alloc Allocated 1280 at 0x81979800
[   10.490000] ag7240_ring_alloc Allocated 4032 at 0x81a09000
[   10.500000] Setting PHY...
[   13.510000] ag7240_ring_free Freeing at 0x81979800
[   13.510000] ag7240_ring_free Freeing at 0x81a09000
[   13.530000] ag7240_ring_alloc Allocated 1280 at 0x81b6e000
[   13.530000] ag7240_ring_alloc Allocated 4032 at 0x81a09000
[   13.540000] Setting PHY...
[   16.560000] device eth0 entered promiscuous mode
[   16.570000] ag7240_ring_free Freeing at 0x81979000
[   16.570000] ag7240_ring_free Freeing at 0x81b45000
[   16.590000] ag7240_ring_alloc Allocated 1280 at 0x81b67000
[   16.590000] ag7240_ring_alloc Allocated 4032 at 0x81b45000
[   16.600000] Setting PHY...
[   17.620000] ag7240_ring_free Freeing at 0x81b67000
[   17.620000] ag7240_ring_free Freeing at 0x81b45000
[   17.640000] ag7240_ring_alloc Allocated 1280 at 0x81a57000
[   17.640000] ag7240_ring_alloc Allocated 4032 at 0x81b45000
[   17.650000] Setting PHY...
[   18.660000] device eth1 entered promiscuous mode
sh: can't create /proc/sys/dev/wifi0/pollingmode: nonexistent directory
sh: can't create /proc/sys/dev/wifi0/maxvaps: nonexistent directory
[   18.840000]
[   18.840000]  ath_numswbaperbc = 8(1)adj=76800
ath0
Invalid command : wdssep
[   19.220000] AG7240: enet unit:1 phy:2 is up...Mii 100Mbps full duplex
[   19.230000] AG7240: done cfg2 0x7215 ifctl 0x0 miictrl  
[   22.120000] Data bus error, epc == 80c8d210, ra == 80c8d1fc
[   22.120000] Oops[#1]:
[   22.120000] Cpu 0
[   22.120000] $ 0   : 00000000 00000000 deadc0de ffff3fff
[   22.120000] $ 4   : 80c38000 0000a258 00004000 0000000c
[   22.120000] $ 8   : ffffffff 00000006 00000002 0000001c
[   22.120000] $12   : 80c386cf 0000096c 00000015 80c03a88
[   22.120000] $16   : 0000000c 80c385a8 00000000 80c38000
[   22.120000] $20   : 80c03b10 00000002 818f0078 00000003
[   22.120000] $24   : 0000000c 80c03b16                  
[   22.120000] $28   : 80c02000 80c03a68 80c03ac8 80c8d1fc
[   22.120000] Hi    : 00000020
[   22.120000] Lo    : ba840000
[   22.120000] epc   : 80c8d210 0x80c8d210
[   22.120000]     Tainted: P         
[   22.120000] ra    : 80c8d1fc 0x80c8d1fc
[   22.120000] Status: 1000f402    KERNEL EXL
[   22.120000] Cause : 5080801c
[   22.120000] PrId  : 00019374 (MIPS 24Kc)
[   22.120000] Modules linked in: ath_mimo_pci ath_mimo_hal(P)
[   22.120000] Process ifconfig (pid: 606, threadinfo=80c02000, task=81b2f6c0, tls=00000000)
[   22.120000] Stack : 00000000 00000000 00000000 00000000 80c03ab0 00000008 00000000 00000000
[   22.120000]         00030002 1c000000 70222222 22803f00 00000000 00000001 096c096c 096c98a0
[   22.120000]         00000000 00000001 701a1a1a 1a1a1a1a 1a000000 00000000 00000000 00803f00
[   22.120000]         001c001c 001c001c 001c001c 001c001c 00220022 00220022 00220022 0022001c
[   22.120000]         001a001a 001a001a 001a001a 001a001a 00000000 00000000 00000000 00000000
[   22.120000]         ...
[   22.120000] Call Trace:[<80020007>] 0x80020007
[   22.120000] [<800f2c6c>] 0x800f2c6c
[   22.120000] [<800f2cc8>] 0x800f2cc8
[   22.120000] [<80052fcc>] 0x80052fcc
[   22.120000] [<800f2c6c>] 0x800f2c6c
[   22.120000] [<800f2d28>] 0x800f2d28
[   22.120000] [<8015b8c8>] 0x8015b8c8
[   22.120000] [<80c9ce48>] 0x80c9ce48
[   22.120000] [<80c966e8>] 0x80c966e8
[   22.120000] [<80c9dc3c>] 0x80c9dc3c
[   22.120000] [<8015b09c>] 0x8015b09c
[   22.120000] [<80d08304>] 0x80d08304
[   22.120000] [<801515b0>] 0x801515b0
[   22.120000] [<80151f5c>] 0x80151f5c
[   22.120000] [<80d33d24>] 0x80d33d24
[   22.120000] [<80037e4c>] 0x80037e4c
[   22.120000] [<801515b0>] 0x801515b0
[   22.120000] [<8014d6ac>] 0x8014d6ac
[   22.120000] [<8014d8dc>] 0x8014d8dc
[   22.120000] [<80151490>] 0x80151490
[   22.120000] [<80152278>] 0x80152278
[   22.120000] [<801c5a8c>] 0x801c5a8c
[   22.120000] [<80152d7c>] 0x80152d7c
[   22.120000] [<8013eba8>] 0x8013eba8
[   22.120000] [<8007ffb4>] 0x8007ffb4
[   22.120000] [<801402c0>] 0x801402c0
[   22.120000] [<800806b4>] 0x800806b4
[   22.120000] [<80140354>] 0x80140354
[   22.120000] [<80073e14>] 0x80073e14
[   22.120000] [<80080758>] 0x80080758
[   22.120000] [<80070768>] 0x80070768
[   22.120000] [<80004144>] 0x80004144
[   22.120000]
[   22.120000]
[   22.120000] Code: 00033380  3c03ffff  34633fff <00431024> 30c6ffff  00c23025  3405a258  0c32942c  02602021
Segmentation fault

max***

Autobooting in 1 seconds
按tpl

wl***

Autobooting in 1 seconds
按tpl
maxneo 发表于 2010-12-30 00:15

请问您是看了别人的帖子，还是亲身体验的？我tp和tpl都试过，都没有中断过，如果您操作成功了，是不是有什么别的窍门？请楼上明示？

7296***

在出现提示后再按
我840n和941n都试过

wl***

在出现提示后再按
我840n和941n都试过
729650915 发表于 2010-12-30 08:20

那FW150R有没有试过呢？
搜遍帖子，FW150R究竟有没有人TTL成功过啊？还望有经验的不吝赐教，谢谢！

wl***

最新战况，在试过无数次后终于通过按“tpl”中断了启动(其实我估计也有可能是只需要“TP”两个，因为中断后提示符后面出现输入“LLLLL”估计是tp已经中断了，“l”当做命令被输入进去，只是猜测，无论怎样总算是成功了，离成功又迈进一大步了，值得庆幸！！！)但是随之而来的是另一个问题，命令“flash -noheader : flash1.trx”不被识别，显示如下：
U-Boot 1.1.4 (Dec  3 2009 - 10:03:23)

AP91 (ar7240) U-boot
DRAM:  
sri
#### TAP VALUE 1 = a, 2 = b
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 2.6.34.7-svn15928 (root@dd-wrt) (gcc version 4.3.3 (GCC) ) #2414 Sat Dec 18 09:36:59 CET 2010
[    0.000000] flash_size passed from bootloader = 4
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Booting AR7240(Python)...
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29696k/32768k available (1999k kernel code, 3072k reserved, 336k data, 144k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 232.65 BogoMIPS (lpj=1163264)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] NET: Registered protocol family 16
[    0.240000] PCI init:ar7240_pcibios_init
[    0.240000] registering PCI controller with io_map_base unset
[    0.250000] bio: create slab <bio-0> at 0
[    0.260000] PCI: fixup device 0000:00:00.0
[    0.270000] found calibration data for slot 0 on 0xBF3F1000
[    0.280000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    0.290000] pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff 64bit] (PCI address [0x10000000-0x1000ffff]
[    0.300000] Returning IRQ 48
[    0.300000] fixup irq: got 48
[    0.300000] Switching to clocksource MIPS
[    0.310000] NET: Registered protocol family 2
[    0.310000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.320000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.330000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.330000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.340000] TCP reno registered
[    0.340000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.350000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.350000] NET: Registered protocol family 1
[    0.360000] gpio_proc: module loaded and /proc/gpio/ created
[    0.370000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[    0.370000] init_vdso successfull
[    0.380000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[    0.380000] msgmni has been set to 58
[    0.390000] io scheduler noop registered
[    0.390000] io scheduler deadline registered (default)
[    0.400000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.410000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
[    0.410000] console [ttyS0] enabled, bootconsole disabled
[    0.410000] console [ttyS0] enabled, bootconsole disabled
[    0.420000] guessed flashsize = 4M
[    0.430000] scanning for root partition
[    0.430000] tplink uboot detected
[    0.440000] guessed bootloader size = 20000
[    0.440000]
[    0.440000] found squashfs at 160000
[    0.450000] Creating 8 MTD partitions on "ar7240-nor0":
[    0.450000] 0x000000000000-0x000000020000 : "RedBoot"
[    0.460000] 0x000000020000-0x0000003e0000 : "linux"
[    0.470000] 0x000000160000-0x0000003d0000 : "rootfs"
[    0.470000] mtd: partition "rootfs" set to be root filesystem
[    0.480000] 0x0000003d0000-0x0000003e0000 : "ddwrt"
[    0.480000] 0x0000003e0000-0x0000003f0000 : "nvram"
[    0.490000] 0x0000003f0000-0x000000400000 : "board_config"
[    0.500000] 0x000000000000-0x000000400000 : "fullflash"
[    0.500000] 0x000000000000-0x000000020000 : "fullboot"
[    0.510000] PPP generic driver version 2.4.2
[    0.520000] PPP Deflate Compression module registered
[    0.520000] PPP BSD Compression module registered
[    0.530000] PPP MPPE Compression module registered
[    0.530000] NET: Registered protocol family 24
[    0.540000] PPPoL2TP kernel driver, V1.0
[    0.540000] IMQ driver loaded successfully.
[    0.540000]  Hooking IMQ before NAT on PREROUTING.
[    0.550000]  Hooking IMQ after NAT on POSTROUTING.
[    0.550000] tun: Universal TUN/TAP device driver, 1.6
[    0.560000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.570000] AG7240: Length per segment 1544
[    0.570000] AG7240: Max segments per packet 1
[    0.570000] AG7240: Max tx descriptor count    80
[    0.580000] AG7240: Max rx descriptor count    252
[    0.580000] AG7240: fifo cfg 3 01f00140
[    0.590000] AG7240CHH: Mac address for unit 0
[    0.590000] AG7240CHH: ff:ff:ff:ff:ff:ff
[    0.800000] AG7240CHH: Mac address for unit 1
[    0.800000] AG7240CHH: ff:ff:ff:ff:ff:ff
[    1.010000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[    1.020000] u32 classifier
[    1.020000]     input device check on
[    1.020000]     Actions configured
[    1.030000] Netfilter messages via NETLINK v0.30.
[    1.030000] nf_conntrack version 0.5.0 (464 buckets, 1856 max)
[    1.040000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    1.040000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    1.050000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    1.060000] nf_conntrack_rtsp v0.6.21 loading
[    1.060000] nf_nat_rtsp v0.6.21 loading
[    1.070000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.070000] IPP2P v0.8.2 loading
[    1.080000] TCP westwood registered
[    1.080000] TCP hybla registered
[    1.080000] TCP vegas registered
[    1.090000] NET: Registered protocol family 17
[    1.090000] Bridge firewalling registered
[    1.100000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    1.100000] All bugs added by David S. Miller <davem@redhat.com>
[    1.150000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.150000] Freeing unused kernel memory: 144k freed
start service
starting Architecture code for wr741
Jan  1 00:00:02 udevtrigger[161]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory


U-Boot 1.1.4 (Dec  3 2009 - 10:03:23)

AP91 (ar7240) U-boot
DRAM:  
sri
#### TAP VALUE 1 = a, 2 = b
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
ar7240> flash -noheader : flash1.trx
Unknown command 'flash' - try 'help'
ar7240>

tuo***

等高人回帖学习

max***

兄弟你看到“Autobooting in 1 seconds”快速按“tpl”，就可以
中断，我的就是FW150R跟你的一样的，这２天在搞UBNT，信号好点，改了天线，总的来说80元比较值。

天***

终于知道是什么问题了..原来要去掉那个电阻的.后来我把电阻去掉是去掉了.只是又直接把两个点给连接起来了.哎..理解错误..误事呀...