高手帮我分析一下FW150 WAN口故障 附PUUTY会话

gw***

是这样的  
我的FW150R刷了DD后变砖  
然后我按照tuoniao的帖子https://www.right.com.cn/forum/thread-45494-1-1.html
用TTL线修复成功,
现在出现WAN口只出不进,
不管是PPPOE还是动态IP  
都是只发送  
无法获取IP
刷FW150原厂固件  741固件  DD固件均无法解决...  
帮我分析一下把 我很菜



=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.03.07 02:14:29 =~=~=~=~=~=~=~=~=~=~=~=


U-Boot 1.1.4 (Dec 11 2010 - 01:32:26)

AP91 (ar7240) U-boot mod by AVBIOS
DRAM:  
sri
#### TAP VALUE 1 = 8, 2 = 8
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Booting AR7240(Python)...

Linux version 2.6.15--LSDK-7.3.0.300 gcc version 3.4.4 #18 Wed Feb 10 10:33:56 CST 2010

flash_size passed from bootloader = 4

CPU revision is: 00019374

Determined physical RAM map:

memory: 02000000 @ 00000000 (usable)

User-defined physical RAM map:

memory: 02000000 @ 00000000 (usable)

Built 1 zonelists

Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/sbin/init mtdparts=ar7100-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art) mem=32M

Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

PID hash table entries: 256 (order: 8, 4096 bytes)

Using 200.000 MHz high precision timer.

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 30548k/32768k available (1368k kernel code, 2204k reserved, 292k data, 128k init, 0k highmem)

Mount-cache hash table entries: 512

Checking for 'wait' instruction...  available.

NET: Registered protocol family 16

Reset button pressed.

Returning IRQ 48

AR7240 GPIOC major 0

squashfs: version 3.3 (2007/10/31) Phillip Lougher

squashfs: LZMA suppport for slax.org by jro

Initializing Cryptographic API

io scheduler noop registered

io scheduler deadline registered

Serial: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A

RAMDISK driver initialized: 1 RAM disks of 8192K size 1024 blocksize

PPP generic driver version 2.4.2

NET: Registered protocol family 24

cmdlinepart partition parsing not available

Searching for RedBoot partition table

5 RedBoot partitions found on MTD device ar7240-nor0

Creating 5 MTD partitions on "ar7240-nor0":

0x00000000-0x00020000 : "boot"

0x00020000-0x00120000 : "kernel"

0x00120000-0x003e0000 : "rootfs"

0x003e0000-0x003f0000 : "config"

0x003f0000-0x00400000 : "art"

->Oops: flash id 0x1c3116 .

NET: Registered protocol family 2

IP route cache hash table entries: 512 (order: -1, 2048 bytes)

TCP established hash table entries: 2048 (order: 1, 8192 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

TCP bic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (squashfs filesystem) readonly.

Freeing unused kernel memory: 128k freed


init started:  BusyBox v1.01 (2009.12.10-12:12+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5

ip_conntrack version 2.4 (256 buckets, 5120 max) - 244 bytes per conntrack

insmod: cannot open module `/lib/modules/2.6.15/kernel/flashid.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.15/kernel/harmony.ko': No such file or directory
Now flash open!

Now flash open!

sys_mode=0 mac:8106c000 ag7240_macs[0]:00000000 ag7240_macs[1]:8106c000

2

sys_mode=0 mac:81c10000 ag7240_macs[0]:81c10000 ag7240_macs[1]:8106c000

1


(none) mips #18 Wed Feb 10 10:33:56 CST 2010 (none)

(none) login: sys_mode 0 PHY4 auto-negotiation enable

Attention: PHY4  Class A setting in debug 5 register which is not described in DS

phy_setup ethUnit:0 phyUnit:4

Port 4, Neg Success

++++ phy_up is 1, fdx is 1, speed is 1

ATHRS26: resetting s26

ATHRS26: s26 reset done

sys_mode 0 PHY0 auto-negotiation enable

Attention: PHY 0 Class A setting in debug 5 register which is not described in DS

sys_mode 0 PHY1 auto-negotiation enable

Attention: PHY 1 Class A setting in debug 5 register which is not described in DS

sys_mode 0 PHY2 auto-negotiation enable

Attention: PHY 2 Class A setting in debug 5 register which is not described in DS

sys_mode 0 PHY3 auto-negotiation enable

Attention: PHY 3 Class A setting in debug 5 register which is not described in DS

phy_setup ethUnit:1 phyUnit:0

phy_setup ethUnit:1 phyUnit:1

phy_setup ethUnit:1 phyUnit:2

phy_setup ethUnit:1 phyUnit:3

Port 0, Neg Success

Port 1, Neg Success

Port 2, Neg Success

Port 3, Neg Success

++++ phy_up is 0, fdx is 0, speed is 0

device eth0 entered promiscuous mode

phy_setup ethUnit:1 phyUnit:0

phy_setup ethUnit:1 phyUnit:1

phy_setup ethUnit:1 phyUnit:2

phy_setup ethUnit:1 phyUnit:3

Port 0, Neg Success

Port 1, Neg Success

Port 2, Neg Success

Port 3, Neg Success

++++ phy_up is 1, fdx is 0, speed is 0

AG7240: enet unit:0 phy:4 is up...Mii 10Mbps half duplex

AG7240: enet unit 0 phy 4 mode 0x4c04

++++ phy_up is 1, fdx is 1, speed is 1

AG7240: enet unit:1 phy:3 is up...Mii 100Mbps full duplex

AG7240: enet unit 1 phy 3 mode 0x4c04

br0: port 1(eth0) entering learning state

br0: topology change detected, propagating

br0: port 1(eth0) entering forwarding state

++++ phy_up is 0, fdx is 0, speed is 0

AG7240: unit 1: phy 3 not up carrier 1

br0: port 1(eth0) entering disabled state

ath_hal: module license 'Proprietary' taints kernel.

ath_hal: 0.9.17.1 (AR5416, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)

wlan: 0.8.4.2 (Atheros/multi-bss)

ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved

ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved

ath_pci: 0.9.4.5 (Atheros/multi-bss)

wifi0: Atheros 9285: mem=0x10000000, irq=48 hw_base=0xb0000000

wlan_me: Version 0.1

Copyright (c) 2008 Atheros Communications, Inc. All Rights Reserved

wlan: mac acl policy registered

++++ phy_up is 1, fdx is 1, speed is 1

AG7240: enet unit:1 phy:3 is up...Mii 100Mbps full duplex

AG7240: enet unit 1 phy 3 mode 0x4c04

br0: port 1(eth0) entering learning state

br0: topology change detected, propagating

br0: port 1(eth0) entering forwarding state


TP_Flags:6****

ap_start_405:Test by Songwei!


++++ phy_up is 0, fdx is 0, speed is 0

AG7240: unit 1: phy 3 not up carrier 1

br0: port 1(eth0) entering disabled state

++++ phy_up is 1, fdx is 1, speed is 1

AG7240: enet unit:1 phy:3 is up...Mii 100Mbps full duplex

AG7240: enet unit 1 phy 3 mode 0x4c04

br0: port 1(eth0) entering learning state

br0: topology change detected, propagating

br0: port 1(eth0) entering forwarding state

++++ phy_up is 0, fdx is 0, speed is 0

AG7240: unit 1: phy 3 not up carrier 1

br0: port 1(eth0) entering disabled state

++++ phy_up is 1, fdx is 1, speed is 0

AG7240: enet unit:1 phy:3 is up...Mii 10Mbps full duplex

AG7240: enet unit 1 phy 3 mode 0x4c04

br0: port 1(eth0) entering learning state

br0: topology change detected, propagating

br0: port 1(eth0) entering forwarding state

The selected channel is 1

Country ie is CN

Country ie is CN

maxrate = 150000

Country ie is CN

br0: port 1(eth0) entering disabled state

phy_setup ethUnit:1 phyUnit:0

phy_setup ethUnit:1 phyUnit:1

phy_setup ethUnit:1 phyUnit:2

phy_setup ethUnit:1 phyUnit:3

Port 0, Neg Success

Port 1, Neg Success

Port 2, Neg Success

Port 3, Neg Success

device ath0 entered promiscuous mode

br0: port 2(ath0) entering learning state

br0: topology change detected, propagating

br0: port 2(ath0) entering forwarding state

br0: port 2(ath0) entering disabled state

Country ie is CN

br0: port 2(ath0) entering learning state

br0: topology change detected, propagating

br0: port 2(ath0) entering forwarding state

++++ phy_up is 1, fdx is 1, speed is 1

AG7240: enet unit:1 phy:3 is up...Mii 100Mbps full duplex

AG7240: enet unit 1 phy 3 mode 0x4c04

br0: port 1(eth0) entering learning state

br0: topology change detected, propagating

br0: port 1(eth0) entering forwarding state

br0: port 2(ath0) entering disabled state


TP_Flags:6****


TP_Flags:0****

Country ie is CN

br0: port 2(ath0) entering learning state

br0: topology change detected, propagating

br0: port 2(ath0) entering forwarding state

+++ GE0 RX DMA ENABLE

Inteference detected

rx_clear=100, rx_frame=0, tx_frame=0


TL-WR741N/742N mips #18 Wed Feb 10 10:33:56 CST 2010 (none)

TL-WR741N/742N login: admin
Password:
Login incorrect
TL-WR741N/742N login:

tuo***

你的问题我没碰到，所以帮不到你，觉的你可以刷回厂固件后，用reset一下试试。

bs***

用无线联接试下，刷回厂固件试下

是不是线断了一根呢。

gw***

3# bsctv

谢谢楼上几位的回答 好几天没管他了   今天插电测试发现  奇迹般的复活了 哈哈