哪位精通编译的能将OSCAM运行到tomato下！

sa***

转帖：

Binaries Asus WL500gP OlegFirmware (mipsel)

Here we go!

I dont know which libs are really needed, but i set on depends: libusb openssl pcsclite ccid

libusb and openssl should download ipkg automatically (maybe run ipkg update first).

Then first install pcsc-lite_155_thE29.ipk at cmd line with:
Zitat:
ipkg install pcsc-lite_155_thE29.ipk

then install ccid_1311_thE29.ipk:
Zitat:
ipkg install ccid_1311_thE29.ipk


And then you could install oscam-*-oleg-thE29.ipk
It should install libusb and openssl from the internet!

To remove older versions just say:
Zitat:
ipkg remove oscam

and install the newer package (or just install it again, normaly the oscam.conf should not be overwritten, as it is not a part of the ipk)

The configuration files are located in
Zitat:
/opt/etc/oscam

I also putted the doc into the folder with the examples and in text version!

Because i just can upload zipped files, i tar-ed the files!
When you download the files, upload it to your router and say:
Zitat:
tar -xf file.tar

Or unzip it with windows/linux/mac and upload it as .ipk

The pcsc-lite and ccid packages are just in the first post, because the will not need an upgrade so early (IMHO  )


Please test the version and report the bugs, because i just tested oscam as remote server.
So the oscam on my Asus connected to my dreambox oscam (with camd3 line) and shared it with camd3. It worked with my tested card (SD & HD channels) on kathrein 910 with camd3.902.
But I didnt test any usb reader. I will get a smargo next week so i can test it then.


Edit: To run Omnikey 3121 (and maybe 3021) you NEED pcsc-lite_155!
Normaly when you install like the instruction above you should have the pcsclite and ccid installed.
Problem is that the depends entry in the ipkg file doesnt work. Normaly you cannot install oscam without this 2 libs.
And BEFORE you plug in the Omnikey run the program: pcscd to enable communication with cardreader and oscam!

I will test smargo when i get mine (next week).[

Attachments:
pcsc-lite_155_thE29.ipk.tar (260 KB, 441 downloads)
ccid_1311_thE29.ipk.tar (100 KB, 359 downloads)
oscam-0.99.4svn620-oleg-thE29.ipk.tar (190 KB, 184 downloads)
oscam-0.99.4svn620_reader-oleg-thE29.ipk.tar (190 KB, 177 downloads)
oscam-0.99.4svn820-oleg-thE29.ipk.tar (200 KB, 172 downloads)  下载地址：  http://satku.qupan.cc/6951865.html

sa***

参考

文件“oscam-svn4670-light-Distribution.tar”上传成功，下载地址：http://satku.qupan.cc/6951875.html

hous***

我成功了，路由器是H618B，就是启动太慢了。其中走了不少弯路，最早用的是中文的Daul WAN版本，没成功，换成最新Beta英文原版USB的Tomato就可以，USB口插一个8G的普通U盘做交换分区和数据/opt分区使用。目前还有一些小问题，继续折腾。

myfr***

openwrt最简单 直接上传就可以 运行速度很快 不用u盘 不用任何程序 直接就支持 还支持usb的读卡器 很简单 很方便 需要程序联系我 都是自己编译的 官方编译的不能用

myfr***

rg100a  db120  都没问题的 速度很快 开机自己启动 路由超级便宜 呵呵

sa***

我成功了，路由器是H618B，就是启动太慢了。其中走了不少弯路，最早用的是中文的Daul WAN版本，没成功，换成最新Beta英文原版USB的Tomato就可以，USB口插一个8G的普通U盘做交换分区和数据/opt分区使用。目前还有一些 ...
housecall 发表于 2011-2-3 11:27

我用中文的Daul WAN版本转发账号也可以啊！

lu***

我用中文的Daul WAN版本转发账号也可以啊！
satku 发表于 2011-2-4 19:36

偶水平太次，还在学习中，能否分享一下你的oscam.conf和oscam.server，谢谢！

sa***

openwrt最简单 直接上传就可以 运行速度很快 不用u盘 不用任何程序 直接就支持 还支持usb的读卡器 很简单 很方便 需要程序联系我 都是自己编译的 官方编译的不能用
myfriends 发表于 2011-2-3 19:57

openwrt我玩不定啊！嫩否来个详细点的教程，造福大家啊

sa***

偶水平太次，还在学习中，能否分享一下你的oscam.conf和oscam.server，谢谢！
luojx 发表于 2011-2-4 20:18

账号转发标准配置，没读卡器，读卡没法试

hous***

这两天折腾了一下，同时请教了luojx,终于搞定了DD-WRT、Openwrt、Tomato三个系统下OSCAM的标准帐号转发。
所用的设备：DB120 标准版安装的Openwrt；H618b标准版安装的Tomato，Linksys WRT54G安装的DD-WRT，全部都不使用USB口接存储或USB驱动。
以上纯粹是学习，不是为了去转发购买的帐号，严重BS私自转发帐号行为。

sa***

文件下载：
http://bbs.satku.com/bbs/forum.p ... mp;tid=7&extra=

myfr***

呵呵 安装openwrt教程等我的机器来了给大家做个 呵呵

lw***

呵呵 安装openwrt教程等我的机器来了给大家做个 呵呵
myfriends 发表于 2011-2-8 23:23

期待学习下，DD-WRT、Tomato下的安装也做个教程吧。

myfr***

https://www.right.com.cn/forum/thread-45436-1-1.html
这里有 呵呵