|
|
本帖最后由 wpzin 于 2016-2-24 14:21 编辑
刷楼主的Breed后无法支持TP-link 原厂固件？ 如果这是这样我没有问题了，原先我以为刷了Breed后可以支持TP国内固件，即vxworks!
我的路由是WR840N V2,和841N v8是一样的配置。R883 breed,先刷的843ND固件可以正常启动，然后刷840N V2 原厂固件 无法启动，换R717breed同样的结果。刷编程器固件也无法启动（保留 breed）
TP-LINK布局，刷原厂固件后，TTL信息如下：
breed>
breed> Upgrade completed.
Rebooting in 2 seconds ...
Resetting ...
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2016 HackPascal <hackpascal@gmail.com>
Build date 2016-01-23 [git-0053995]
Version 1.0 (r833)
DRAM: 16MB
Platform: Atheros AR9341 rev 1
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: EON EN25Q32 (4MB) on ath79-spi
ag71xx-eth: Using MAC address 8c:21:6a:4e:64:1c
eth0: Atheros AR8228/AR8229 rev 1
Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Press any key to interrupt autoboot ... 0
Unable to locate firmware.
Starting breed built-in shell
breed>
刷843ND可以正常启动，TP-LINK布局，TTL信息如下：
breed> Upgrade completed.
Rebooting in 2 seconds ...
Resetting ...
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2016 HackPascal <hackpascal@gmail.com>
Build date 2016-01-23 [git-0053995]
Version 1.0 (r833)
DRAM: 16MB
Platform: Atheros AR9341 rev 1
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: EON EN25Q32 (4MB) on ath79-spi
ag71xx-eth: Using MAC address 8c:21:6a:4e:64:1c
eth0: Atheros AR8228/AR8229 rev 1
Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Press any key to interrupt autoboot ... 0
Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
Image Name: 08430001
Data Size: 812380 Bytes
Load Address: 80002000
Entry Point: 801a9c60
Uncompressing data (LZMA) ... done.
Flushing cache ... done.
Starting kernel at 0x801a9c60...
Booting Atheros AR934x
榠nux version 2.6.31--LSDK-9.2.0_U5.508 (zhongjin@rd3linux.tplink) (gcc version 4.3.3 (GCC) ) #64 Mon Jul 23 17:26:00 CST 2012
flash_size passed from bootloader = 4
Ram size passed from bootloader =16777216
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 400 ahb 200
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 13888k/16384k available (1723k kernel code, 2496k reserved, 426k data, 112k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 27
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "art"
->Oops: flash id 0x1c3016 .
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 112k freed
init started: BusyBox v1.01 (2012.07.19-00:43+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (256 buckets, 5120 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
(none) mips #64 Mon Jul 23 17:26:00 CST 2012 (none)
(none) login: Now flash open!
Now flash open!
Now flash open!
Now flash open!
Now flash open!
Now flash open!
Now flash open!
Now flash open!
Now flash open!
Now flash open!
Now flash open!
Now flash open!
Erase from 0X3E0000 to 0X3EC804:.
Program from 0X3E0000 to 0X3EC804:
write successfully
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:1 Registering S27....
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 40
ATHR_GMAC: Max rx descriptor count : 128
ATHR_GMAC: Mac capability flags : 2D82
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:0 Registering S27....
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 40
ATHR_GMAC: Max rx descriptor count : 128
ATHR_GMAC: Mac capability flags : 2582
athr_gmac_ring_alloc Allocated 640 at 0x80b8ec00
athr_gmac_ring_alloc Allocated 2048 at 0x80cce000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at 0x80b8e800
athr_gmac_ring_alloc Allocated 2048 at 0x80bc2800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
ATHRS27: resetting s27
ATHRS27: s27 reset done
++++ athrs27_igmp_setup once
port0 vid is 0xb000b
port1 vid is 0x30003
port2 vid is 0x50005
port3 vid is 0x70007
port4 vid is 0x90009
++ PVID: 0x0000000b, bitmap: 0x0000001f
++ PVID: 0x00000003, bitmap: 0x0000001f
++ PVID: 0x00000005, bitmap: 0x0000001f
++ PVID: 0x00000007, bitmap: 0x0000001f
++ PVID: 0x00000009, bitmap: 0x0000001f
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
Setting PHY...
device eth0 entered promiscuous mode
Now flash open!
athr_gmac_ring_free Freeing at 0x80b8e800
athr_gmac_ring_free Freeing at 0x80bc2800
athr_gmac_ring_alloc Allocated 640 at 0x80b8e800
athr_gmac_ring_alloc Allocated 2048 at 0x80bc2000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
enet1 port2 up
ATHR_GMAC: Enet Unit:1 PHY:2 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
====>>>>DHCP start.dhcpc.c,dhcpcStart,914
====>>>>dhcpcStart: dhcpcInterfaceName(ath7) does not exsit, start false!
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
ath_get_caps[5105] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5080] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
====>>>>SystemMode : APC Router
wlan_vap_create : enter. devhandle=0x806e02c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x806e02c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created
====>>>>wlan: rand channel 7
DES SSID SET=TP-LINK_4E641C
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
Free buffer count 256
sc_txq[0] :
sc_txq[0] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[1] :
sc_txq[1] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[2] :
sc_txq[2] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[3] :
sc_txq[3] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[6] :
sc_txq[6] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[7] :
sc_txq[7] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[8] :
sc_txq[8] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
***********************************
athr_gmac_ring_free Freeing at 0x80b8e800
athr_gmac_ring_free Freeing at 0x80bc2000
br0: port 1(eth0) entering disabled state
athr_gmac_ring_alloc Allocated 640 at 0x80b8e800
athr_gmac_ring_alloc Allocated 2048 at 0x80bc4800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Free buffer count 256
sc_txq[0] :
sc_txq[0] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[1] :
sc_txq[1] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[2] :
sc_txq[2] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[3] :
sc_txq[3] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[6] :
sc_txq[6] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[7] :
sc_txq[7] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[8] :
sc_txq[8] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
***********************************
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
br0: port 2(ath0) entering disabled state
DES SSID SET=TP-LINK_4E641C
Free buffer count 256
sc_txq[0] :
sc_txq[0] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[1] :
sc_txq[1] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[2] :
sc_txq[2] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[3] :
sc_txq[3] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[6] :
sc_txq[6] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[7] :
sc_txq[7] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
sc_txq[8] :
sc_txq[8] : depth is 0
aggr_depth is 0 tidBufCount 0 bufQCount 0 axq_cnt 0
***********************************
br0: port 2(ath0) entering forwarding state
enet1 port2 up
ATHR_GMAC: Enet Unit:1 PHY:2 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
====>>>>cmdCtrl open success
====>>>>eventCtrl open success
====>>>>eventCtrl attach success
VAP device ath7 created
device ath7 entered promiscuous mode
br0: port 3(ath7) entering forwarding state
br0: port 3(ath7) entering disabled state
device ath7 left promiscuous mode
br0: port 3(ath7) entering disabled state
device eth1 entered promiscuous mode
====>>>>root_ap's BSSID is 0, down ath7
====>>>>ATH0 MAC: 8C:21:6A:4E:64:1C
====>>>>Cloned MAC: 8C:21:6A:4E:64:1D
====>>>>MAC MASK: FF:FF:FF:FF:FF:FE
====>>>>STOPPED == info.status.dhcpcSendMsg,995
====>>>>DHCP start.dhcpc.c,dhcpcStart,914
====>>>>DHCP end.dhcpc.c,dhcpcStart,974
====>>>>Clone Wan Mac for APC Router
ATHR_GMAC: GE0 RX DMA ENABLE
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2016-2-16 10:46
显身卡