|
本帖最后由 fuger 于 2013-8-13 00:43 编辑
TTL信息:(能看到,但是无法输入,波特率57600)
U-Boot 1.1.3 (Jun 9 2013 - 13:49:24)
Board: Ralink APSoC DRAM: 8 MB
relocate_code Pointer at: 807b4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 42
spi device id: 1c 70 15 1c 70 (70151c70)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 64 Mbits SDR
DRAM bus: 16 bit
Total memory: 8 MBytes
Flash component: SPI Flash
Date:Jun 9 2013 Time:13:49:24
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 600 MHZ ####
estimate memory size =8 Mbytes
raspi_read: from:1f0000 len:10000
Readstrval:751(4)
cccc:l
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 3
0
3: System Boot system code via Flash.
aa7c7f85,ff8079,1a319d
update kernel image
the image is bad,into emgry image!
cccccccccccccccccccccccccccccccc
bbbbbbbbbb
## Booting image at bc180000 ...
raspi_read: from:180000 len:40
Image Name: zxrouter
Image Type: MIPS Linux Standalone Program (uncompressed)
Data Size: 279008 Bytes = 272.5 kB
Load Address: 80500000
Entry Point: 80500000
raspi_read: from:180040 len:441e0
load_addr:80500000,data_addr:180040,len:441e0,data:bc180040
Verifying Checksum ... OK
OK
cccccccccccccccccccccccccccc1
cccccccccccccccccccccccccccc2:80500000
ZzOK
ifra305x eth0: init pnde=800af7d0, sc=800af1dc, ifp=800af3ac
ifra305x: driver init
ifra305x: init numtxd=128 txd-base=800 at a00d2ea0
ifra305x: init num_rxd=64 rxd_base=900 at a00d36a0
ifra305x eth1: init pnde=800af7e0, sc=800af2ac, ifp=800af3f4
netcore_process:147
not find ok flash,use default 0
asdfaaaaaa
aaaa:l
wan:l
vvvvvvvvvvvvv:f,1
vvvvvvvvvvvvv:10,2
netcore_process:172
module:NW710
main_loop:424 *****************
________________Interface_Lan_Num_tm=0______________________
Interface_Num:-2146341280
kuaiwan ad:1
prep_ifaces:ifaces_found:0, dev->irq1:15
prep_ifaces:ifaces_found:1, dev->irq1:9
prep_ifaces:ifaces_found:2, dev->irq1:0
prep_ifaces:ifaces_found:3, dev->irq1:0
prep_ifaces:ifaces_found:4, dev->irq1:0
all pkt ________________________ 181
revcq init
if_start 294 iface:0
if_start 294 iface:1
flashenhanced/src/ver1/flash_up_function_read.cpp:31 pFlashAddress:1d0000,pRamAddress:80116c98,Length:54
flashenhanced/src/ver1/flash_sst_read.cpp:105
flashenhanced/src/ver1/flash_up_function_read.cpp:31 pFlashAddress:1e0000,pRamAddress:80116c98,Length:54
flashenhanced/src/ver1/flash_sst_read.cpp:105
LAN_IP=192.168.1.1,unusemem=4096KB
reg:baddbadd baddbadd baddbadd baddbadd baddbadd baddbadd
CFG_load: flash offset=0000, len=1058
cfg_parse: add cfg item=313 (4184 bytes)
CFG_load: flash read 313 items(4184 bytes) into ram
cfg_parse: null config!
CFG_load: read-only 2 items(48 bytes) into ram
CFG_load: total 315 items(4232 bytes)
cfg_parse_wlan: parse 3028 bytes!
Parsing WIFI configuration succeeds
amain:210
Operation Mode: Gateway
bug:ifr_link_cmd:1157
interface eth0 init_net successed!
eth0_1_com_ioctl:1512 Init device 'ra305x_eth0'
eth0_1_com_ioctl:1512 Init device 'ra305x_eth0'
ifra305x0: start
bug:ifr_link_cmd:1157
eth0_1_com_ioctl:1512 Init device 'ra305x_eth0'
eth0_1_com_ioctl:1512 Init device 'ra305x_eth0'
ifra305x1: start
main:241
led light error |
|