JCG Q10Pro/Q20 可用的breed和pb boot，breed可刷的老毛子和op

ada***

由于部分用户反馈刷过度固件变砖。建议不要从过渡固件刷bootloader（breed或pb boot），直接官方固件下刷bootloader。
先备份，然后ssh刷入。ssh备份参考如下
https://www.right.com.cn/forum/thread-5556381-1-1.html


……………………………………………………………………………………………………………………………………………………………………
本方法已经过时，不怕变砖的可以试试，因为官方固件升级了。以下方法，很可能会导致变砖。我之前老固件是没问题的，但很多新固件的朋友用了直接变砖。
一. 从官方固件刷breed（如果是很老的固件，应该没问题。新固件会变砖头。具体版本我也不清楚，最好别刷）

1. 1.刷解锁bootloader的op过渡固件
   
2.    openwrt-ramips-mt7621-jcg_q20-squashfs-factory.bin
   
3. 2.putty mtd命令写入 小米r3g的breed：
   
4.    mtd write /tmp/breed-mt7621-xiaomi-r3g.bin Bootloader

复制代码

二.从官方固件刷pb boot（如果是很老的固件，应该没问题。新固件会变砖头。具体版本我也不清楚，最好别刷。）

1. 1.刷解锁bootloader的op过渡固件
   
2.    openwrt-ramips-mt7621-jcg_q20-squashfs-factory.bin
   
3. 2.putty mtd命令写入 cr6606的pb boot：
   
4.    mtd write /tmp/pb-boot.img Bootloader
   

复制代码

三.从breed到pb boot


四.从pb boot到breed，直接pb boot页面下刷入breed      


……………………………………………………………………………………………………………………………………………………………………………………………………
个人体验：breed能刷的固件很少，群友的openwrt和padavan可以刷（亲测，wifi能跑800m，也可以pb boot下刷入，灯和wan完美适配），还有集客ap 246nd（亲测）。
链接：https://pan.baidu.com/s/18zQoIH24Ayv3TgnvcEPKrw
提取码：91ho
感谢群友Victor大佬提供的固件
………………………………………………………
下面来看看我体验过的padavan:以下都是pb boot刷入。
——————————————————————————————————————————————————————————————————————————
固件个人推荐：1.dajie125的pandavan（电梯直达）

1. 特性：无任何插件纯净版，完美适配灯和wan, 无线500M左右。开启hw nat后，有800m左右。

复制代码

——————————————————————————————————————————————————————————————————————————

2.yuyangyu755 的 padavan（电梯直达）

1. 特性：比较精简，只有学西上网和内网穿透。, 无线500M左右
   
2. 刷入：我从dajie125的老毛子，web下刷入的。也可以从刷了cr6608的pb boot，直接刷入。
   
3. 1.wan和灯在0729版本已经修复了
   
4. 网关：192.168.2.1
   
5. https://www.right.com.cn/FORUM/thread-4153232-1-2.html
   

复制代码

——————————————————————————————————————————————————————————————————————————
3. 刷hiboy的 cr660x padavan (电梯直达)

1. 特性：功能齐全，更新很快，无线400M左右
   
2. 网关：192.168.123.1

复制代码

4. 刷237176253的 cr660x padavan (电梯直达)

1. 特性：功能够用，wifi调校很棒，无线800M左右

复制代码

嘿***

支持！可以刷breed了

ada***

嘿嘿 发表于 2021-7-29 13:22
支持！可以刷breed了

breed能刷的固件很少，群友的openwrt可以刷（亲测），还有集客ap 246nd（本人未测，机友说可以）。适配breed的固件很少。

飞炫***

发现了，用cr660x的pbboot，可以刷很多cr660x的固件，就是会网口反向和led灯不正常

ada***

飞炫冰火 发表于 2021-7-29 15:53
发现了，用cr660x的pbboot，可以刷很多cr660x的固件，就是会网口反向和led灯不正常

这个问题不大，习惯就好

gui***

请问一下，jcg q20刷了集客ap的固件，可以直接刷老毛子固件吗？

ada***

guigeng 发表于 2021-7-29 17:55
请问一下，jcg q20刷了集客ap的固件，可以直接刷老毛子固件吗？

不清楚。
ttl刷机可以，其他不清楚。

cc08***

刷了集客经常掉线，烦死了

ke***

0729版本在那下？原作者网盘没有。

ada***

keben 发表于 2021-7-30 20:34
0729版本在那下？原作者网盘没有。

我网盘里面有，百度网盘

ke***

adagiov 发表于 2021-7-30 21:21
我网盘里面有，百度网盘

多谢，正在下。

ko***

楼主您好，我用pd的网页刷入了hiboy的固件后不能用了，现在putty显示如下：
MT7530 set LAN/WAN LLLLW                                                      0
Booting from Flash...
Booting image from bc200000 ...
   Image Name:   JCG-Q20
   Image Type:   MIPS Linux Kernel Image (uncompressed)
   Data Size:    18225195 Bytes = 17.4 MB
   Load Address: 80001000
   Entry Point:  805e5e00
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
   Flushing cache from 0x80001000 size 18225195 ... OK

INUX started...
Linux version 3.4.113 (root@hiboy-VirtualBox) (gcc version 4.4.7 (GCC) ) #4 SMP Mon Aug 2 02:20:00 CST 2021

MediaTek SoC: MT7621A, RevID: 0103, RAM: DDR3, XTAL: 40MHz
CPU/OCP/SYS frequency: 880/293/220 MHz
CONFIG_RALINK_RAM_SIZE:256MB
prom get memory:256MB
CPU revision is: 0001992f (MIPS 1004Kc)
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00010000
Movable zone start PFN for each node
Early memory PFN ranges
    0: 0x00000000 -> 0x00010000
Detected 3 available secondary CPU(s)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
PERCPU: Embedded 7 pages/cpu @81203000 s5984 r8192 d14496 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock5 rootfstype=squashfs
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Writing ErrCtl register=0000026e
Readback ErrCtl register=0000026e
Memory: 248360k/262144k available (6071k kernel code, 13784k reserved, 4975k data, 212k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:72
MIPS GIC RevID: 3.0
Setting up vectored interrupts
console [ttyS0] enabled
Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 1: done.
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 2: done.
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 3: done.
Brought up 4 CPUs
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref]
pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x603fffff pref]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref]
pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [mem 0x60000000-0x601fffff pref]
pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit pref]
pci 0000:02:00.0: BAR 2: assigned [mem 0x60300000-0x60303fff 64bit pref]
pci 0000:02:00.0: BAR 4: assigned [mem 0x60304000-0x60304fff 64bit pref]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0:   bridge window [mem 0x60200000-0x603fffff pref]
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay (lpj = 1167360)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 485
io scheduler noop registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000c00 (irq = 34) is a 16550A
Ralink GPIO driver initialized. Number of GPIO: 64, GPIO mode: 000A85A8
loop: module loaded
MediaTek NAND driver init, version v2.1
MTK NFI: NAND ID [C8 D1, 80 95 40 7F]
MTK NFI: NAND chip found in MTK table: F59L1G81MB
NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (ESMT NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
Scanning device for bad blocks
MTK NFI: success load FACT_BBT from block 1023
Creating 10 MTD partitions on "MT7621-NAND":
0x000000000000-0x000000040000 : "Bootloader"
0x000000040000-0x000000080000 : "BootEnv"
0x000000080000-0x000000100000 : "Config"
0x000000100000-0x000000180000 : "Factory"
0x000000180000-0x000000380000 : "Kernel"
0x000000380000-0x000001980000 : "RootFS"
0x000001980000-0x000001d80000 : "Storage"
0x000001d80000-0x000007f80000 : "RWFS"
0x000000180000-0x000001980000 : "Firmware_Stub"
0x000000000000-0x000007f80000 : "ALL"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Ralink APSoC Ethernet Driver v3.2.4 (raeth)
raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536
raeth: NAPI & GRO support, weight 64
raeth: Byte Queue Limits (BQL) support
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
p p t p driver version 0.8.5
register mt_drv
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
<--mt7916_hif_init()
Rx[0] Ring: total 24576 bytes allocated
Rx[1] Ring: total 16384 bytes allocated
<-- pci_alloc_tx_rx_ring_mem, Status=0
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)


=== pAd = c0301000, size = 11497216 ===

<-- RTMPAllocAdapterBlock, Status=0
PCI CSRBaseAddress =0xc0200000, csr_addr=0xc0200000!
RTMPInitPCIeDevice():device_id=0x7915
mt7915_init()-->
Use the default iPAiLNA bin image!
<--mt7915_init()
RtmpOSFileOpen(): Error 2 opening /etc_ro/Wireless/l1profile.dat
Rx[0] Ring: total 24576 bytes allocated
Rx[1] Ring: total 24576 bytes allocated
Rx[2] Ring: total 8192 bytes allocated
Rx[3] Ring: total 16384 bytes allocated
Rx[4] Ring: total 8192 bytes allocated
<-- pci_alloc_tx_rx_ring_mem, Status=0
nf_conntrack version 0.5.0 (32768 buckets, 32768 max)
xt_time: kernel timezone is -0000
Bridge firewalling registered
gre: GRE over IPv4 demultiplexor driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
ASUS NVRAM, v0.08. Available space: 131072. Integrity: Signature FAILED!
List of all partitions:
1f00             256 mtdblock0  (driver?)
1f01             256 mtdblock1  (driver?)
1f02             512 mtdblock2  (driver?)
1f03             512 mtdblock3  (driver?)
1f04            2048 mtdblock4  (driver?)
1f05           22528 mtdblock5  (driver?)
1f06            4096 mtdblock6  (driver?)
1f07          100352 mtdblock7  (driver?)
1f08           24576 mtdblock8  (driver?)
1f09          130560 mtdblock9  (driver?)
No filesystem could mount root, tried:  squashfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)




请问有什么办法处理吗？

SZh***

楼主

1. openwrt-ramips-mt7621-jcg_q20-squashfs-factory.bin

复制代码

和

1. openwrt-ramips-mt7621-jcg_q10p-Q20-breed-squashfs-factory.bin

复制代码

这两个命名上很像啊，看上边的说明

1. openwrt-ramips-mt7621-jcg_q10p-Q20-breed-squashfs-factory.bin

复制代码

这个是网友定制的完美openwrt，意思是不是如果不想刷CR660X的pb-boot，那么直接

1.     1.刷解锁bootloader的op过渡固件
   
2.        openwrt-ramips-mt7621-jcg_q20-squashfs-factory.bin
   
3.     2.putty mtd命令写入 小米r3g的breed：
   
4.        mtd write /tmp/breed-mt7621-xiaomi-r3g.bin Bootloader
   
5.     3.重启后进入breed，刷网友定制的完美openwrt
   
6.     openwrt-ramips-mt7621-jcg_q10p-Q20-breed-squashfs-factory.bin

复制代码

这样就好了？
那你分享的百度网盘里“JCG Q20 unlock bootloader openwrt firmware”文件夹里的

1. openwrt-ramips-mt7621-jcg_q20-squashfs-sysupgrade.bin

复制代码

是干嘛用的呀

SZh***

SZhen邦 发表于 2021-8-2 22:35
楼主

和

哦哦  对于

1. openwrt-ramips-mt7621-jcg_q20-squashfs-sysupgrade.bin

复制代码

从“【2021-7-29】捷稀JCG Q20|Q10pro OpenWrt/Padavan固件|支持wifi6|”这个帖子里看到了------“直接原厂固件Web页面升级factory.bin即可，已刷OP固件的直接web界面更新sysupgrade.bin即可（不要保存配置）”，脑子有点懵了，打扰了

ada***

kofz 发表于 2021-8-2 16:48
楼主您好，我用pd的网页刷入了hiboy的固件后不能用了，现在putty显示如下：
MT7530 set LAN/WAN LLLLW     ...

pb boot其实是有用了。如果你进不起pb boot。先试试清浏览器换成，或者换成无痕模式。还不行，就路由器和电脑都重启了。