找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 532|回复: 6

WNDR4700 刷openwrt报错重启,求助!

[复制链接]
WNDR4700 刷openwrt报错重启


TTL 启动代码如下:

131072 bytes read: OK
Net:   ppc_4xx_eth0
AR8327 GigaSW initialize...done
ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0)

Client starts...[Listening] for ADVERTISE...TTT
Retry count exceeded; boot the image as usual

nmrp server is stopped or failed !

Type run flash_nfs to mount root filesystem over NFS

Hit any key to stop autoboot:  0

Loading from device 0: NAND 128MiB 3,3V 8-bit (offset 0x180000)
Skipping bad block 0x00240000

** check device-tree image **
   Verifying Checksum ... OK

** check kernel image **
   Verifying Checksum ... OK

** check rootfs image **
   Verifying Checksum ... OK

NAND read: device 0 offset 0x180000, size 0x20000
131072 bytes read: OK
## Booting kernel from Legacy Image at 00500000 ...
   Image Name:   POWERPC OpenWrt Linux-4.14.275
   Image Type:   PowerPC Linux Kernel Image (lzma compressed)
   Data Size:    1956316 Bytes =  1.9 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 00800040
   Booting using the fdt blob at 0x800040
   Uncompressing Kernel Image ... OK
[    0.000000] Linux version 4.14.275 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11427-9ce6aa9d8d)) #0 Sat Apr 16 13:13:32 2022
[    0.000000] Using WNDR4700 Platform machine description
[    0.000000] -----------------------------------------------------
[    0.000000] phys_mem_size     = 0x10000000
[    0.000000] dcache_bsize      = 0x20
[    0.000000] icache_bsize      = 0x20
[    0.000000] cpu_features      = 0x0000000010100040
[    0.000000]   possible        = 0x0000000030100040
[    0.000000]   always          = 0x0000000010100040
[    0.000000] cpu_user_features = 0x8c008000 0x00000000
[    0.000000] mmu_features      = 0x00000008
[    0.000000] -----------------------------------------------------
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 253904K/262144K available (4608K kernel code, 196K rwdata, 604K rodata, 180K init, 241K bss, 8240K reserved, 0K cma-reserved)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xfffdf000..0xfffff000  : fixmap
[    0.000000]   * 0xfde00000..0xfe000000  : consistent mem
[    0.000000]   * 0xfde00000..0xfde00000  : early ioremap
[    0.000000]   * 0xd1000000..0xfde00000  : vmalloc & ioremap
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[    0.000000] UIC0 (32 IRQ sources) at DCR 0xc0
[    0.000000] UIC1 (32 IRQ sources) at DCR 0xd0
[    0.000000] UIC2 (32 IRQ sources) at DCR 0xe0
[    0.000000] UIC3 (32 IRQ sources) at DCR 0xf0
[    0.000015] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    0.000025] clocksource: timebase mult[800000] shift[23] registered
[    0.000089] pid_max: default: 32768 minimum: 301
[    0.000203] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000218] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.003324] random: get_random_u32 called from 0xc01eef3c with crng_init=0
[    0.003567] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.003591] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.004058] NET: Registered protocol family 16
[    0.004989] PPC4XX OCM1: 32768 Bytes (enabled)
[    0.005008] PPC4XX OCM1: 32768 Bytes (non-cached)
[    0.005013] PPC4XX OCM1: 0 Bytes (cached)
[    0.005064] debugfs ppc4xx ocm: failed to create file
[    0.005238] 256k L2-cache enabled
[    0.005341] PCIE0: Checking link...
[    0.005347] PCIE0: Device detected, waiting for link...
[    0.005352] PCIE0: link is up !
[    0.113711] PCI host bridge /plb/pciex@d00000000 (primary) ranges:
[    0.113738]  MEM 0x0000000e00000000..0x0000000e7fffffff -> 0x0000000080000000
[    0.113748]  MEM 0x0000000f00000000..0x0000000f000fffff -> 0x0000000000000000
[    0.113756]   IO 0x0000000f80000000..0x0000000f8000ffff -> 0x0000000000000000
[    0.113775] 4xx PCI DMA offset set to 0x00000000
[    0.113779] 4xx PCI DMA window base to 0x0000000000000000
[    0.113784] DMA window size 0x0000000080000000
[    0.113807] PCIE0: successfully set as root-complex
[    0.114382] PCI: Probing PCI hardware
[    0.114515] PCI host bridge to bus 0000:40
[    0.114533] pci_bus 0000:40: root bus resource [io  0x0000-0xffff]
[    0.114543] pci_bus 0000:40: root bus resource [mem 0xe00000000-0xe7fffffff] (bus address [0x80000000-0xffffffff])
[    0.114554] pci_bus 0000:40: root bus resource [mem 0xf00000000-0xf000fffff] (bus address [0x00000000-0x000fffff])
[    0.114564] pci_bus 0000:40: root bus resource [bus 40-ff]
[    0.114672] PCI: Hiding 4xx host bridge resources 0000:40:00.0
[    0.115030] pci 0000:41:00.0: enabling Extended Tags
[    0.115237] pci 0000:40:00.0: PCI bridge to [bus 41-7f]
[    0.115278] pci 0000:41:00.0: bridge configuration invalid ([bus 02-05]), reconfiguring
[    0.115493] pci 0000:42:02.0: enabling Extended Tags
[    0.115805] pci 0000:42:03.0: enabling Extended Tags
[    0.116095] pci 0000:42:04.0: enabling Extended Tags
[    0.116356] pci 0000:41:00.0: PCI bridge to [bus 42-7f]
[    0.116403] pci 0000:42:02.0: bridge configuration invalid ([bus 03-03]), reconfiguring
[    0.116417] pci 0000:42:03.0: bridge configuration invalid ([bus 04-04]), reconfiguring
[    0.116430] pci 0000:42:04.0: bridge configuration invalid ([bus 05-05]), reconfiguring
[    0.116941] pci 0000:42:02.0: PCI bridge to [bus 43-7f]
[    0.117589] pci 0000:42:03.0: PCI bridge to [bus 44-7f]
[    0.118207] pci 0000:42:04.0: PCI bridge to [bus 45-7f]
[    0.118343] pci 0000:40:00.0: Max Payload Size set to  128/ 256 (was  256), Max Read Rq  256
[    0.118361] pci 0000:41:00.0: Max Payload Size set to  128/ 256 (was  128), Max Read Rq  128
[    0.118377] pci 0000:42:02.0: Max Payload Size set to  128/ 256 (was  128), Max Read Rq  128
[    0.118395] pci 0000:43:00.0: Max Payload Size set to  128/ 128 (was  128), Max Read Rq  512
[    0.118410] pci 0000:42:03.0: Max Payload Size set to  128/ 256 (was  128), Max Read Rq  128
[    0.118427] pci 0000:44:00.0: Max Payload Size set to  128/ 128 (was  128), Max Read Rq  512
[    0.118443] pci 0000:42:04.0: Max Payload Size set to  128/ 256 (was  128), Max Read Rq  128
[    0.118462] pci 0000:45:00.0: Max Payload Size set to  128/ 128 (was  128), Max Read Rq  512
[    0.118571] pci 0000:40:00.0: disabling bridge window [io  0x0000-0xffffffffffffffff] to [bus 41-7f] (unused)
[    0.118597] pci 0000:40:00.0: BAR 8: assigned [mem 0xe00000000-0xe002fffff]
[    0.118610] pci 0000:41:00.0: BAR 8: assigned [mem 0xe00000000-0xe002fffff]
[    0.118622] pci 0000:42:02.0: BAR 8: assigned [mem 0xe00000000-0xe000fffff]
[    0.118631] pci 0000:42:03.0: BAR 8: assigned [mem 0xe00100000-0xe001fffff]
[    0.118640] pci 0000:42:04.0: BAR 8: assigned [mem 0xe00200000-0xe002fffff]
[    0.118653] pci 0000:43:00.0: BAR 0: assigned [mem 0xe00000000-0xe0001ffff 64bit]
[    0.118674] pci 0000:43:00.0: BAR 6: assigned [mem 0xe00020000-0xe0002ffff pref]
[    0.118682] pci 0000:42:02.0: PCI bridge to [bus 43]
[    0.118694] pci 0000:42:02.0:   bridge window [mem 0xe00000000-0xe000fffff]
[    0.118709] pci 0000:44:00.0: BAR 0: assigned [mem 0xe00100000-0xe0011ffff 64bit]
[    0.118728] pci 0000:44:00.0: BAR 6: assigned [mem 0xe00120000-0xe0012ffff pref]
[    0.118736] pci 0000:42:03.0: PCI bridge to [bus 44]
[    0.118746] pci 0000:42:03.0:   bridge window [mem 0xe00100000-0xe001fffff]
[    0.118761] pci 0000:45:00.0: BAR 0: assigned [mem 0xe00200000-0xe00201fff 64bit]
[    0.118780] pci 0000:42:04.0: PCI bridge to [bus 45]
[    0.118790] pci 0000:42:04.0:   bridge window [mem 0xe00200000-0xe002fffff]
[    0.118801] pci 0000:41:00.0: PCI bridge to [bus 42-45]
[    0.118811] pci 0000:41:00.0:   bridge window [mem 0xe00000000-0xe002fffff]
[    0.118823] pci 0000:40:00.0: PCI bridge to [bus 41-7f]
[    0.118832] pci 0000:40:00.0:   bridge window [mem 0xe00000000-0xe002fffff]
[    0.127489] SCSI subsystem initialized
[    0.129382] clocksource: Switched to clocksource timebase
[    0.130291] NET: Registered protocol family 2
[    0.130419] IP idents hash table entries: 4096 (order: 3, 32768 bytes)
[    0.130842] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.130868] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.130889] TCP: Hash tables configured (established 2048 bind 2048)
[    0.130971] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.130989] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.131095] NET: Registered protocol family 1
[    5.979250] pci 0000:45:00.0: xHCI HW not ready after 5 sec (HC bug?) status = 0x801
[    5.982939] OF: /plb/opb/gpio@ef600b00: could not find phandle
[    5.984191] dw_dmac 4bffd0800.dma: DesignWare DMA Controller, 2 channels
[    5.987936] Crashlog allocated RAM at address 0x3f00000
[    5.988651] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    5.991562] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    6.000181] io scheduler noop registered
[    6.000196] io scheduler deadline registered (default)
[    6.001742] aer: probe of 0000:40:00.0:pcie002 failed with error -22
[    6.001806] pcie_pme: probe of 0000:40:00.0:pcie001 failed with error -22
[    6.001910] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    6.003641] console [ttyS0] disabled
[    6.003693] 4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 37, base_baud = 347222) is a TI16750
[    6.818296] console [ttyS0] enabled
[    6.822333] sata-dwc 4bffd1800.sata: id 0, controller version 1.91
[    6.829778] scsi host0: sata-dwc
[    6.833190] ata1: SATA max UDMA/133 irq 46
[    6.838438] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    6.844775] nand: Hynix H27U1G8F2BTR-BC
[    6.848600] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    6.856158] Scanning device for bad blocks
[    6.861382] Bad eraseblock 18 at 0x000000240000
[    6.926984] 12 fixed-partitions partitions found on MTD device 4e4000000.ndfc.nand
[    6.934535] Creating 12 MTD partitions on "4e4000000.ndfc.nand":
[    6.940525] 0x000000000000-0x000008000000 : "NAND 128MiB 3,3V 8-bit"
[    6.948142] 0x000000000000-0x000000180000 : "uboot"
[    6.953448] 0x000000180000-0x0000001a0000 : "device-tree"
[    6.959246] 0x000000180000-0x000000500000 : "kernel"
[    6.964670] 0x000000500000-0x0000019e0000 : "ubi"
[    6.969910] 0x0000019e0000-0x000001a60000 : "config"
[    6.975287] 0x000001a60000-0x000001ae0000 : "pot"
[    6.980421] 0x000001ae0000-0x000001de0000 : "traffic_meter"
[    6.986436] 0x000001de0000-0x000001fa0000 : "language"
[    6.991981] 0x000001fa0000-0x000007fc0000 : "ecos"
[    6.997774] 0x000007fc0000-0x000008000000 : "wifi_data"
[    7.003444] 0x000000180000-0x0000019e0000 : "firmware"
[    7.009603] PPC 4xx OCP EMAC driver, version 3.54
[    7.014617] MAL v2 /plb/mcmal, 1 TX channels, 1 RX channels
[    7.020342] RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support
[    7.027499] TAH /plb/opb/emac-tah@ef601350 initialized
[    7.032901] /plb/opb/emac-rgmii@ef601500: input 0 in rgmii mode
[    7.045172] switch0: Atheros AR8327 rev. 4 switch registered on 4ef600c00.ethernet
[    7.166453] ata1: SATA link down (SStatus 0 SControl 300)
[    7.606016] eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 20:e5:2a:68:c8:15
[    7.612885] eth0: found Atheros AR8216/AR8236/AR8316 PHY (0x00)
[    7.618972] i2c /dev entries driver
[    7.622881] ibm-iic 4ef600700.i2c: using standard (100 kHz) mode
[    7.649596] booke_wdt: powerpc book-e watchdog driver loaded
[    7.658069] NET: Registered protocol family 10
[    7.663992] Segment Routing with IPv6
[    7.667730] NET: Registered protocol family 17
[    7.672200] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    7.685109] 8021q: 802.1Q VLAN Support v1.8
[    7.691475] UBI error: no valid UBI magic found inside mtd4
[    7.697054] hctosys: unable to open rtc device (rtc0)
[    7.702735] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    7.710203] Please append a correct "root=" boot option; here are the available partitions:
[    7.718524] 1f00          131072 mtdblock0
[    7.718527]  (driver?)
[    7.725050] 1f01            1536 mtdblock1
[    7.725052]  (driver?)
[    7.731573] 1f02             128 mtdblock2
[    7.731575]  (driver?)
[    7.738096] 1f03            3584 mtdblock3
[    7.738098]  (driver?)
[    7.744619] 1f04           21376 mtdblock4
[    7.744621]  (driver?)
[    7.751142] 1f05             512 mtdblock5
[    7.751144]  (driver?)
[    7.757666] 1f06             512 mtdblock6
[    7.757668]  (driver?)
[    7.764188] 1f07            3072 mtdblock7
[    7.764190]  (driver?)
[    7.770712] 1f08            1792 mtdblock8
[    7.770714]  (driver?)
[    7.777235] 1f09           98432 mtdblock9
[    7.777237]  (driver?)
[    7.783758] 1f0a             256 mtdblock10
[    7.783760]  (driver?)
[    7.790371] 1f0b           24960 mtdblock11
[    7.790373]  (driver?)
[    7.796978] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    7.806324] Rebooting in 1 seconds..
Auto calibration ---


我的恩山、我的无线 The best wifi forum is right here.
昨天刷的,没问题。
按住4700复位键开机,直到绿灯闪白色,松手。

点评

你刷的哪个固件??  详情 回复 发表于 2024-4-22 19:17
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

刷的新版本?
ttl
4. in the Prompt enter the following commands (copy & paste)

setenv bootcmd "if loadn_dniimg 0 0x180000 0xae0000 && chk_dniimg 0xae0000; then bootm 0xb00000 - 0xae0040;else fw_recovery; fi"
saveenv
run bootcmd


TTL


setenv bootcmd "if loadn_dniimg 0 0x180000 0xae0000 && chk_dniimg 0xae0000; then bootm 0xb00000 - 0xae0040;else fw_recovery; fi"
saveenv
run bootcmd
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

w7x8x 发表于 2023-6-30 13:26
昨天刷的,没问题。
按住4700复位键开机,直到绿灯闪白色,松手。

你刷的哪个固件??

点评

这个路由器就那么两个固件,好像是论坛里解决扩容的那个固件。  详情 回复 发表于 2024-4-25 09:11
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

rivale 发表于 2024-4-22 19:17
你刷的哪个固件??

这个路由器就那么两个固件,好像是论坛里解决扩容的那个固件。

点评

4700 刷机后 用起来怎么样? 5g,2.4g都稳定吗?会不会断流,掉线?  详情 回复 发表于 2024-4-26 12:36
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

w7x8x 发表于 2024-4-25 09:11
这个路由器就那么两个固件,好像是论坛里解决扩容的那个固件。

4700 刷机后 用起来怎么样?   5g,2.4g都稳定吗?会不会断流,掉线?

点评

没怎么用,记得当时正常。  详情 回复 发表于 2024-4-26 19:10
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

rivale 发表于 2024-4-26 12:36
4700 刷机后 用起来怎么样?   5g,2.4g都稳定吗?会不会断流,掉线?

没怎么用,记得当时正常。不是主路由器。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-29 00:16

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表