中兴ZTE E8820V1/E8821刷第三方固件研究

afeng11

1、E8820v1可以刷breed，但32M闪存刷任何固件都无法启动；
2、E8821因为双闪存缘故，breed并不支持，需拆机通过ttl刷机；
3、E8820v1可实现免拆刷第三方uboot或者breed；
4、E8820v1和E8821免拆不死uboot均已适配。


[    0.000000] Linux version 5.10.221 (xuzhun@afeng11) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 8.4.0 r20413-d9d9e37e34) 8.4.0, GNU ld (GNU Binutils) 2.37)
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is ZTE E8821
[    0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 288 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stackff, heap allocff, heap freeff
[    0.000000] Memory: 120324K/131072K available (6092K kernel code, 589K rwdata, 1312K rodata, 1212K init, 205K bss, 10748K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 775.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[    0.000008] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[    0.008898] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.075943] pid_max: default: 32768 minimum: 301
[    0.081312] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.089621] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.100468] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.111844] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.123043] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.130865] pinctrl core: initialized pinctrl subsystem
[    0.138190] NET: Registered protocol family 16
[    0.198489] clocksource: Switched to clocksource MIPS
[    0.205408] NET: Registered protocol family 2
[    0.210652] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.219487] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.229079] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.237783] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.245822] TCP: Hash tables configured (established 1024 bind 1024)
[    0.253163] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.260635] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.268841] NET: Registered protocol family 1
[    0.273822] PCI: CLS 0 bytes, default 32
[    0.287420] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.298385] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.305064] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.320028] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.327591] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.335535] printk: console [ttyS0] disabled
[    0.340520] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[    0.350337] printk: console [ttyS0] enabled
[    0.359403] printk: bootconsole [early0] disabled
[    0.380944] spi-nand spi0.1: Winbond SPI NAND was found.
[    0.386446] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[    0.397341] 3 fixed-partitions partitions found on MTD device (null)
[    0.403959] Creating 3 MTD partitions on "(null)":
[    0.408946] 0x000000000000-0x000000400000 : "kernel"
[    0.419053] 0x000000400000-0x000001a00000 : "ubi"
[    0.447250] 0x000001a00000-0x000008000000 : "reserved"
[    0.558948] spi-nor spi0.0: s25fl008k (1024 Kbytes)
[    0.564042] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.570703] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.577560] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.585265] Creating 4 MTD partitions on "spi0.0":
[    0.590271] 0x000000000000-0x000000040000 : "u-boot"
[    0.598374] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.604941] 0x000000050000-0x000000060000 : "art"
[    0.612362] 0x000000060000-0x000000100000 : "config"
[    1.312538] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[    1.970023] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    1.981323] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[    1.990195] NET: Registered protocol family 10
[    2.002998] Segment Routing with IPv6
[    2.006895] NET: Registered protocol family 17
[    2.011643] 8021q: 802.1Q VLAN Support v1.8
[    2.020026] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[    2.026350]  MEM 0x0000000012000000..0x0000000013ffffff
[    2.031801]   IO 0x0000000000000000..0x0000000000000000
[    2.037376] PCI host bridge to bus 0000:00
[    2.041659] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    2.048780] pci_bus 0000:00: root bus resource [io  0x0000]
[    2.054534] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.061554] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.069797] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[    2.076033] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    2.083112] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    2.090122] pci 0000:00:00.0: supports D1
[    2.094262] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    2.101425] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    2.108284] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    2.115895] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[    2.128046] UBI: auto-attach mtd1
[    2.131547] ubi0: attaching mtd1
[    2.650645] ubi0: scanning is finished
[    2.689418] ubi0: attached mtd1 (name "ubi", size 22 MiB)
[    2.695005] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.702145] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.709176] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.716361] ubi0: good PEBs: 176, bad PEBs: 0, corrupted PEBs: 0
[    2.722576] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    2.730048] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1738844539
[    2.739497] ubi0: available PEBs: 0, total reserved PEBs: 176, PEBs reserved for bad PEB handling: 20
[    2.749145] ubi0: background thread "ubi_bgt0d" started, PID 297
[    2.758284] block ubiblock0_0: created from ubi0:0(rootfs)
[    2.764012] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    2.771437] clk: Disabling unused clocks
[    2.797707] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.811761] Freeing unused kernel memory: 1212K
[    2.816445] This architecture does not have kernel memory protection.
[    2.823131] Run /sbin/init as init process
[    2.827355]   with arguments:
[    2.827360]     /sbin/init
[    2.827363]   with environment:
[    2.827367]     HOME=/
[    2.827371]     TERM=linux
[    3.666531] init: Console is alive
[    3.670570] init: - watchdog -
[    6.735507] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.972512] usbcore: registered new interface driver usbfs
[    6.978250] usbcore: registered new interface driver hub
[    6.983885] usbcore: registered new device driver usb
[    6.998112] Button Hotplug driver version 0.4.1
[    7.008027] raid6: skip pq benchmark and using algorithm int32x8
[    7.014312] raid6: using intx1 recovery algorithm
[    7.020908] xor: measuring software checksum speed
[    7.042324]    8regs           :   601 MB/sec
[    7.063255]    8regs_prefetch  :   599 MB/sec
[    7.078631]    32regs          :   906 MB/sec
[    7.095238]    32regs_prefetch :   813 MB/sec
[    7.099748] xor: using function: 32regs (906 MB/sec)
[    7.572396] Btrfs loaded, crc32c=crc32c-generic
[    7.617977] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.634749] SCSI subsystem initialized
[    7.644893] fsl-ehci: Freescale EHCI Host controller driver
[    7.653663] ehci-platform: EHCI generic platform driver
[    7.659491] ehci-platform 1b000000.usb: EHCI Host Controller
[    7.665396] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[    7.673645] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[    7.708513] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[    7.715757] hub 1-0:1.0: USB hub found
[    7.720411] hub 1-0:1.0: 1 port detected
[    7.725327] ehci-platform 1b400000.usb: EHCI Host Controller
[    7.731263] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
[    7.739528] ehci-platform 1b400000.usb: irq 14, io mem 0x1b400000
[    7.768514] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[    7.775732] hub 2-0:1.0: USB hub found
[    7.780453] hub 2-0:1.0: 1 port detected
[    7.793721] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.802197] ohci-platform: OHCI generic platform driver
[    7.811015] uhci_hcd: USB Universal Host Controller Interface driver
[    7.823126] usbcore: registered new interface driver usb-storage
[    7.830611] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    7.848629] init: - preinit -
[    8.269375] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    8.584025] usb-storage 2-1:1.0: USB Mass Storage device detected
[    8.599737] scsi host0: usb-storage 2-1:1.0
[    8.971633] random: procd: uninitialized urandom read (4 bytes read)
[    9.620780] scsi 0:0:0:0: Direct-Access     Generic  Flash Disk       8.07 PQ: 0 ANSI: 4
[    9.645338] sd 0:0:0:0: [sda] 1966080 512-byte logical blocks: (1.01 GB/960 MiB)
[    9.658274] sd 0:0:0:0: [sda] Write Protect is off
[    9.663292] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[    9.671853] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    9.719836]  sda: sda1
[    9.729304] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   10.203857] random: jshn: uninitialized urandom read (4 bytes read)
[   10.287881] random: jshn: uninitialized urandom read (4 bytes read)
[   10.564649] random: jshn: uninitialized urandom read (4 bytes read)
[   12.048685] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 3 is up
[   12.055217] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 5 is up
[   12.075311] eth0: link up (1000Mbps/Full duplex)
[   12.089173] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   12.096061] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   16.501636] mount_root: loading kmods from internal overlay
[   16.558659] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   16.572678] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   17.474198] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   17.489197] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 501
[   17.673025] UBIFS (ubi0:1): recovery needed
[   18.099430] UBIFS (ubi0:1): recovery completed
[   18.104129] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   18.112254] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   18.122510] UBIFS (ubi0:1): FS size: 6602752 bytes (6 MiB, 52 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[   18.132937] UBIFS (ubi0:1): reserved for root: 311863 bytes (304 KiB)
[   18.139614] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID D2A31A38-52AB-4ECA-90BF-504E1FEF0FFB, small LPT model
[   18.158314] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   18.187421] block: extroot: not configured
[   18.192001] UBIFS (ubi0:1): un-mount UBI device 0
[   18.196901] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   18.213889] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   18.228820] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 504
[   18.626370] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   18.634512] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   18.644770] UBIFS (ubi0:1): FS size: 6602752 bytes (6 MiB, 52 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[   18.655194] UBIFS (ubi0:1): reserved for root: 311863 bytes (304 KiB)
[   18.661865] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID D2A31A38-52AB-4ECA-90BF-504E1FEF0FFB, small LPT model
[   18.690223] mount_root: loading kmods from internal overlay
[   18.744305] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   18.761030] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   19.357564] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   19.383833] block: extroot: not configured
[   19.396592] mount_root: switching to ubifs overlay
[   19.447150] urandom-seed: Seeding with /etc/urandom.seed
[   24.954169] eth0: link down
[   24.976646] procd: - early -
[   24.980591] procd: - watchdog -
[   25.854243] procd: - watchdog -
[   26.133711] procd: - ubus -
[   26.440781] random: ubusd: uninitialized urandom read (4 bytes read)
[   26.449829] random: ubusd: uninitialized urandom read (4 bytes read)
[   26.457298] random: ubusd: uninitialized urandom read (4 bytes read)
[   26.473525] procd: - init -
[   28.943459] random: jshn: uninitialized urandom read (4 bytes read)
[   29.187615] random: ubusd: uninitialized urandom read (4 bytes read)
[   29.200874] random: ubus: uninitialized urandom read (4 bytes read)
[   30.287268] kmodloader: loading kernel modules from /etc/modules.d/*
[   31.406246] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[   31.635820] fuse: init (API version 7.32)
[   31.694030] Loading modules backported from Linux version v5.15.162-0-gf45bea23c39cb
[   31.702086] Backport generated by backports.git v5.15.162-1-0-g9fa1c65c
[   31.884458] usbcore: registered new interface driver ums-alauda
[   31.912281] usbcore: registered new interface driver ums-cypress
[   31.935970] usbcore: registered new interface driver ums-datafab
[   31.963167] usbcore: registered new interface driver ums-freecom
[   31.986821] usbcore: registered new interface driver ums-isd200
[   32.013704] usbcore: registered new interface driver ums-jumpshot
[   32.040804] usbcore: registered new interface driver ums-karma
[   32.063162] usbcore: registered new interface driver ums-sddr09
[   32.090320] usbcore: registered new interface driver ums-sddr55
[   32.114683] usbcore: registered new interface driver ums-usbat
[   32.142643] usbcore: registered new interface driver usblp
[   32.222801] xt_time: kernel timezone is -0000
[   32.877779] urngd: v1.0.2 started.
[   33.611927] PPP generic driver version 2.4.2
[   33.642592] PPP MPPE Compression module registered
[   33.664489] NET: Registered protocol family 24
[   33.818282] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x3c.
[   33.860107] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[   33.868892] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   34.986059] random: crng init done
[   34.989646] random: 25 urandom warning(s) missed due to ratelimiting
[   35.936541] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   39.866887] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[   39.876471] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   39.888704] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[   40.013312] ath10k_pci 0000:00:00.0: Loading BDF type 0
[   40.793116] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   40.884683] ath10k_pci 0000:00:00.0: failed to get board id: -122
[   41.710322] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   41.728253] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[   41.734560] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   41.742855] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[   41.799504] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[   41.814698] ath10k_pci 0000:00:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   41.950012] ath: EEPROM regdomain: 0x0
[   41.950023] ath: EEPROM indicates default country code should be used
[   41.950028] ath: doing EEPROM country->regdmn map search
[   41.950042] ath: country maps to regdmn code: 0x3a
[   41.950048] ath: Country alpha2 being used: US
[   41.950052] ath: Regpair used: 0x3a
[   42.055762] ath: EEPROM regdomain: 0x0
[   42.055774] ath: EEPROM indicates default country code should be used
[   42.055779] ath: doing EEPROM country->regdmn map search
[   42.055793] ath: country maps to regdmn code: 0x3a
[   42.055799] ath: Country alpha2 being used: US
[   42.055803] ath: Regpair used: 0x3a
[   42.066980] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   42.068992] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0x73ba8648, irq=2
[   42.099163] kmodloader: done loading kernel modules from /etc/modules.d/*
[   60.623858] eth0: link up (1000Mbps/Full duplex)
[   60.644166] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   60.652425] device eth0 entered promiscuous mode
[   60.689010] br-lan: port 1(eth0.1) entered blocking state
[   60.694598] br-lan: port 1(eth0.1) entered disabled state
[   60.700524] device eth0.1 entered promiscuous mode
[   60.759281] br-lan: port 1(eth0.1) entered blocking state
[   60.764873] br-lan: port 1(eth0.1) entered forwarding state
[   62.317770] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   68.515229] br-lan: port 2(wlan1) entered blocking state
[   68.520780] br-lan: port 2(wlan1) entered disabled state
[   68.526581] device wlan1 entered promiscuous mode
[   68.714566] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   68.721377] br-lan: port 2(wlan1) entered blocking state
[   68.726885] br-lan: port 2(wlan1) entered forwarding state
[   69.341555] ath10k_pci 0000:00:00.0: failed to get board id: -122
[   70.698380] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   70.716408] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[   70.728553] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   70.736835] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[   70.858536] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[   70.924116] ath10k_pci 0000:00:00.0: rts threshold -1
[   70.944275] br-lan: port 3(wlan0) entered blocking state
[   70.949844] br-lan: port 3(wlan0) entered disabled state
[   70.955655] device wlan0 entered promiscuous mode
[   70.960800] br-lan: port 3(wlan0) entered blocking state
[   70.966310] br-lan: port 3(wlan0) entered forwarding state
[   71.089460] br-lan: port 3(wlan0) entered disabled state
[   74.211420] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   74.218277] br-lan: port 3(wlan0) entered blocking state
[   74.223832] br-lan: port 3(wlan0) entered forwarding state
[  100.099820] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 5 is down
[  101.139491] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 3 is down
[  105.299171] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 3 is up
[  125.059456] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 3 is down
[  130.259171] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 3 is up
[  135.459482] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 5 is up

nianqing126

这路由不错，尽管天线内置，家里用起来信号还是挺好的

afeng11

nianqing126 发表于 2019-5-22 22:20
这路由不错，尽管天线内置，家里用起来信号还是挺好的

已经自己编译固件了，越来越完善了

nianqing126

afeng11 发表于 2019-5-23 15:02
已经自己编译固件了，越来越完善了

就是内存紧张，不适合运行其他插件     

afeng11

nianqing126 发表于 2019-5-23 15:06
就是内存紧张，不适合运行其他插件

是的，内存64有点紧张

corundum

谢谢楼主分享，高通的无线稳定啊。可否提供稳定openwrt固件？

corundum

afeng11 发表于 2019-5-23 15:02
已经自己编译固件了，越来越完善了

我的E8821，是2根天线的。
刷了楼主的提供的breed，再刷一楼固件，提示无法识别固件类型啊。

afeng11

corundum 发表于 2019-5-23 19:38
我的E8821，是2根天线的。
刷了楼主的提供的breed，再刷一楼固件，提示无法识别固件类型啊。

固件在128 nand里面，需要特殊手段才能读取出来

afeng11

corundum 发表于 2019-5-23 19:38
我的E8821，是2根天线的。
刷了楼主的提供的breed，再刷一楼固件，提示无法识别固件类型啊。

要XD3200的固件选择内存布局
刷PandoraBox-ar71xx-generic-jcg-jhr-848q-2019-04-05-git-b4ae2c0bd-squashfs-sysupgrade.bin不用选择内存布局，比较完美

crush

这个和我的MF286基本是一个解决方案,就是MF286多了MINIPCIE 和4G模块

编译个实用点的固件吧, pandora比较臃肿~~ 还有没有流行的去广告和酸酸乳等等功能...

dbwing520

编程器型号 紫薯布丁

mengxgh

这是高手 ，这是高手，你们都是大神，思考了

xinyu1727

afeng11 发表于 2019-5-23 20:06
要XD3200的固件选择内存布局
刷PandoraBox-ar71xx-generic-jcg-jhr-848q-2019-04-05-git-b4ae2c0bd-squa ...

官方固件可以128内存，我改了，只是那个时候还没有办法刷breed ，也没有三方固件用，现在可以了我试试op，

chjw

usb口是usb3.0吗？

nc13177771891

刷不进去   高手看一下